| DTC P0097 | Intake air temperature (IAT) sensor No.2 circuit low input |
|---|---|
|
DETECTION CONDITION
|
• The PCM monitors the IAT sensor No.2 signal. If the voltage at PCM terminal 242 remains low, the PCM determines that there is an IAT sensor No.2 circuit problem.
|
|
POSSIBLE CAUSE
|
• IAT sensor NO.2 malfunction
• Connector or terminal malfunction
• Short to ground in the wiring harness between IAT sensor NO.2 terminal B and PCM terminal 242
• PCM malfunction
|
 |
|
Diagnostic procedure
| STEP | INSPECTION | ACTION | |
|---|---|---|---|
|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has the FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
|
||
|
2
|
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
• Verify related service repair information availability.
• Is any related repair information available?
|
Yes
|
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to the next step.
|
|
No
|
Go to the next step.
|
||
|
3
|
VERIFY CURRENT SIGNAL STATUS: IS CONCERN INTERMITTENT OR CONSTANT?
• Connect the M-MDS to the DLC-2.
• Clear the DTC from the PCM memory using the M-MDS.
• Run the vehicle under the FREEZE FRAME DATA stored condition.
• Is the same DTC present?
|
Yes
|
Go to the next step.
|
|
No
|
Intermittent concern exists.
Perform the “INTERMITTENT CONCERNS TROUBLESHOOTING”.
|
||
|
4
|
CLASSIFY MALFUNCTION AS IAT SENSOR NO.2 MALFUNCTION OR IAT SENSOR SIGNAL CIRCUIT MALFUNCTION
• Connect the M-MDS to DLC-2.
• Access the IAT PID.
• Does the IAT PID indicates 140 °C {284 °F} to -40 °C{-40 °F} after when disconnect the IAT sensor NO.2 connector is disconnected?
|
Yes
|
Go to Step 7.
|
|
No
|
Go to the next step.
|
||
|
5
|
INSPECT IAT SENSOR NO.2
• Inspect the IAT sensor No.2.
• Is there any malfunction?
|
Yes
|
Replace the IAT sensor No.2, then go to Step 10.
|
|
No
|
Go to the next step.
|
||
|
6
|
INSPECT IAT SENSOR NO.2 CONNECTOR FOR POOR CONNECTION
• Turn the engine switch off.
• Disconnect the IAT sensor No.2 connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the terminal, then go to Step 10.
|
|
No
|
Go to Step 10.
|
||
|
7
|
INSPECT IAT SENSOR NO.2 SIGNAL CIRCUIT FOR SHORT TO GROUND
• Turn the engine switch off.
• Inspect for continuity between IAT sensor No.2 terminal B (wiring harness-side) and body ground.
• Is there continuity?
|
Yes
|
Go to the next step.
|
|
No
|
Go to Step 10.
|
||
|
8
|
INSPECT IAT SENSOR NO.2 SIGNAL CIRCUIT FOR SHORT TO GROUND
• Turn the engine switch off.
• Disconnect the PCM connector and the IAT sensor No.2 connector.
• Inspect for continuity between PCM terminal 242 and body ground.
• Is there continuity?
|
Yes
|
Repair or replace the wiring harness for a short to ground between IAT sensor No.2 terminal B and PCM terminal 242, than go to Step 10.
|
|
No
|
Go to the next step.
|
||
|
9
|
INSPECT PCM CONNECTOR FOR POOR CONNECTION
• Turn the engine switch off.
• Disconnect the PCM connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the terminal, then go to the next step.
|
|
No
|
Go to the next step.
|
||
|
10
|
VERIFY THAT DTC P0097 TROUBLESHOOTING IS COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Run the vehicle under the FREEZE FRAME DATA stored condition.
• Is the same DTC present?
|
Yes
|
Replace the PCM, then go to the next step.
|
|
No
|
Go to the next step.
|
||
|
11
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the after repair procedure.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
|
|
No
|
DTC troubleshooting completed.
|
||