P0175 · نشرات الشركة المصنعة

DODGE · 2026-10-03

Flash: Powertrain Control Module (PCM) Updates PCR9A Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P032F-00 - Combustion Engine Producing Insufficient Torque. ● P2D28-00 - Cold Start Propulsion Torque Performance. ● U0075-00 - Control Module Communication Bus "C" Off. ● P0610-00 - Control Module Vehicle Options Error. ● P0630-00 - VIN Not Programmed or Incompatible - ECM/PCM. ● P0607-00 - Control Module Performance. ● P0513-00 - Incorrect Immobilizer Key. ● C0501-00 - Left Front Wheel Speed Sensor "A" Range/Performance. ● C0507-00 - Right Front Wheel Speed Sensor "A" Range/Performance. ● C050D-00 - Left Rear Wheel Speed Sensor "A" Range/Performance. ●…

RAM · 2025-07-04

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0420 - Catalyst System Efficiency Below Threshold Bank 1. ● P0430 - Catalyst System Efficiency Below Threshold Bank 2. ● P0456 - EVAP System Small Leak. ● P06EF - Engine Restart Performance. ● P0175 - Fuel System 2/1 Rich. ● P258B - Electronic Vacuum Pump Performance. ● P0128 - Thermostat Rationality. ● C0062 - Longitudinal Acceleration Sensor. In addition, the customer may experience one or more of the following: ● Vehicle fails emissions inspection testing due to OBD catalyst monitor readiness. ● Engine RPM erratic and or bucking, when accelerating after slowing down. ●…

RAM · 2025-06-25

Flash: Powertrain Control Module (PCM) Updates *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0420 - Catalyst System Efficiency Below Threshold Bank 1. ● P0430 - Catalyst System Efficiency Below Threshold Bank 2.** ● P0456 - EVAP System Small Leak. ● P06EF - Engine Restart Performance. ● P0175 - Fuel System 2/1 Rich. ● P258B - Electronic Vacuum Pump Performance. ● P0128 - Thermostat Rationality. ● C0062 - Longitudinal Acceleration Sensor. In addition, the customer may experience one or more of the following: ● **Vehicle fails emissions inspection testing due to OBD catalyst monitor readiness.** ● Engine RPM erratic and or bucking, when accelerating after slowing…

FORD · 2022-10-19

Some 2019-2021 F-150 vehicles built on or before 04-Mar-2021 and equipped with a 5.0L engine may experience an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTC) P0171, P0172, P0174, P0175, P0364, P060B, P062B, P1104, P164C, P2601, P2BEC, P2BED, P2BEE, P2BEF, P2BF0, P2BF1, P2BF2 and/or P2BF3 stored in the powertrain control module (PCM). This may be due to various software parameters within the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM and reset the keep alive memory (KAM).

RAM · 2022-04-02

Flash: Powertrain Control Module (PCM) Updates RAM 1500 PickupThis bulletin applies to vehicles within the following markets/countries: North America, APAC, EMEA and LATAM. This bulletin applies to vehicles equipped with a 3.6L V6 24V VVT Etorque Engine Upgrade I (Sales Code ERG). Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs have been set: P0607 - ECU Internal Performance. P04FC - Crankcase ventilation system performance. U1817 - Lost Communication With Hybrid Powertrain Control Module On D-PT. U0074 - Dedicated Powertrain D-PT Can Bus Off. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine ifa leak is present…

FORD · 2021-12-14

Some 2019-2020 F-150 vehicles equipped with a 5.0L flex fuel engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0171, P0172, P0174 and/or P0175. This may be due to software parameters in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.

RAM · 2021-08-05

Customer complaint may include the transmission going into neutral on its own. A Mil-on/check engine lamp-on condition may also be present. Upon further investigation, one or more of the following DTCs may be set in the powertrain control module (PCM): P219A-Bank 1 Air-Fuel Ratio Imbalance P219B-Bank 2 Air-Fuel Ratio Imbalance P2173-High Airflow/Vacuum Leak Detected (Slow Accumulation) P2172-High Airflow/Vacuum Leak Detected (Instantaneous Accumulation) P0172-Fuel System 1/1 Rich P0175-Fuel System 2/1 Rich (Incorrect "July 2021" on document)

FORD · 2021-05-18

Some 2021 F-150 vehicles equipped with a 5.0L engine and built on or before 04-Mar-2021 may experience an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTC) P0364, P060B, P062B, P164C, P2601, P0171, P0172, P0174, P0175 and/or P1104 stored in the powertrain control module (PCM). This may be due to various software parameters within the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM and reset the keep alive memory (KAM).

FORD · 2021-03-22

Some 2021 F-150 vehicles equipped with a 5.0L engine and built on or before 08-Mar-2021 may experience an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0364, P060B, P062B, P164C, P2601, P0171, P0172, P0174, P0175, P3450 and/or P1104 stored in the powertrain control module (PCM). This may be due to various software parameters within the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM and reset the keep alive memory (KAM).

FORD · 2020-09-18

Some 2018 F-150 vehicles equipped with a 2.7L EcoBoost engine may experience an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2196, P2198, P2BF0, P2BF2, P2BF1, P2BF3, P2BEC, P2BED, P2BEE, P2BEF, P130D, P0300, P0316, P0301-P0306, P0171, P0174, P219A, P219B, P0172 and/or P0175 stored in the powertrain control module (PCM). This may be due to software in the powertrain control module (PCM) or direct injection fuel injectors leaking down. To correct the condition, follow the Service Procedure to reprogram the PCM and/or replace the direct injection fuel injectors.

FORD · 2020-08-06

Some 2018-2020 F-150 vehicles equipped with a 5.0L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0171, P0172, P0174 and/or P0175. This may be due to incorrect flex fuel learning, which is often caused by customer refueling habits when adding only small amounts of fuel, the vehicle mislearning of inferred ethanol fuel mixture (FF_INF value) or a component concern. Refer to pinpoint test H in the Powertrain Control/Emissions Diagnosis (PC/ED) Manual for diagnostics and Flex Fuel GSB for additional flex fuel system information and diagnostic tips.

RAM · 2020-08-05

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0456 - EVAP System Small Leak. P06EF - Engine Restart Performance. P0175 - Fuel System 2/1 Rich. P258B - Electronic Vacuum Pump Performance. P0128 - Thermostat Rationality. C0062 - Longitudinal Acceleration Sensor. In addition, customers may comment on one or more of the following:A hesitation during aggressive accelerations after an Electronic Stop/Start (ESS) event and the engine is not fully at warm operational temperature. Engine RPM erratic and or bucking, when…

RAM · 2020-08-05

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0456 - EVAP System Small Leak. P06EF - Engine Restart Performance. P0175 - Fuel System 2/1 Rich. P258B - Electronic Vacuum Pump Performance. P0128 - Thermostat Rationality. C0062 - Longitudinal Acceleration Sensor. In addition, customers may comment on one or more of the following:A hesitation during aggressive accelerations after an Electronic Stop/Start (ESS) event and the engine is not fully at warm operational temperature. Engine RPM erratic and or bucking, when…

FORD · 2020-02-20

Some 2018-2020 F-150 vehicles equipped with a 5.0L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0172, P0173, P0174 and/or P0175. This may be due to incorrect flex fuel learning, which is often caused by customer refueling habits or a stuck open evaporative emissions purge valve. Refer to pinpoint test H in the Powertrain Control/Emissions Diagnosis (PC/ED) Manual for diagnostics and Flex Fuel GSB for additional flex fuel system information and diagnostic tips.

TOYOTA · 2020-01-23

TSB: REVISION NOTICE January 23, 2020 Rev1: G1439 The Parts Information, Calibration Information, and Repair Procedure sections have been updated. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0058-13.Service Bulletin No. T-SB-0058-13 is obsolete and any printed versions should be discarded. Some 2009 ? 2018 model year Sequoia and 2009 ? 2019 model year Tundra vehicles equipped with a 3UR-FBE engine may exhibit a hard start and/or MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs): ? DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ? DTC P0172 and/or P0175 (System Too Rich Bank 1/Bank 2) ? DTC P1604 (Startability Malfunction) Techstream data list analysis may reveal negative fuel trims and an…

TOYOTA · 2019-12-06

TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0058-13. Service Bulletin No. T-SB-0058-13 is obsolete and any printed versions should be discarded. Some 2009 ? 2018 model year Sequoia and 2009 ? 2019 model year Tundra vehicles equipped with a 3UR-FBE engine may exhibit a hard start and/or MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs). ? DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ? DTC P0172 and/or P0175 (System Too Rich Bank 1/Bank 2) ? DTC P1604 (Startability Malfunction) Techstream Data List analysis may reveal negative fuel trims and an elevated alcohol density estimate relative to the vehicle?s actual fuel alcohol content. Follow the Repair Procedure in this bulletin to address…

RAM · 2019-05-09

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P0175 - Fuel System 2/1 Rich. P258B - Electronic Vacuum Pump Performance. P0128 - Thermostat Rationality. C0062 - Longitudinal Acceleration Sensor. In addition, the customer may experience one or more of the following:Engine RPM erratic and or bucking, when accelerating after slowing down. Occasional engine shut off while shifting from 4WD low to 2WD. Improvements to the vacuum pump cycle time. Rough idle after cold start.

FORD · 2019-03-25

Some 2015-2018 Transit vehicles built on or before 24-Jul-2018 may exhibit various drivability concerns including difficulty starting, misfires and/or an illuminated MIL with diagnostic trouble codes (DTCs) P00BD, P1247, P1548, P061B, P2195, P2198, P2196, P2197, P0171, P0172, P0174, P0175, P0131 and/or P162F stored in the powertrain control module (PCM). This may be due to undesired water entry into the engine compartment directly over powertrain components. To resolve this condition, install updated water management hardware and/or a revised air cleaner cover.

LEXUS · 2019-01-16

TT: The current engine active test Control the Injection Mode? is not operating as desired when controlling the direct injectors manually on 2GR-FKS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. To avoid this condition, technicians should raise engine RPM when changing back and forth between the Direct Injection and Port Injection active tests. Use the recommended procedure below to avoid this concern while testing injection mode of FKS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel trim and Air to Fuel ratio before returning…

TOYOTA · 2019-01-16

TT: The current engine active test ?Control the Injection Mode? is not operating as desired when controlling the direct injectors manually on 2GR-FKS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. To avoid this condition, technicians should raise engine RPM when changing back and forth between the Direct Injection and Port Injection active tests. Use the recommended procedure below to avoid this concern while testing injection mode of FKS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel trim and Air to Fuel ratio before returning…

FORD · 2018-10-23

Some 2015-2018 Transit vehicles built on or before 24-Jul-2018 may exhibit various drivability concerns including difficulty starting, misfires and/or an illuminated MIL with diagnostic trouble codes (DTCs) P00BD, P1247, P1548, P061B, P2195, P2198, P2196, P2197, P0171, P0172, P0174, P0175, P0131 and/or P162F stored in the powertrain control module (PCM). This may be due to undesired water entry into the engine compartment directly over powertrain components. Follow the Service Procedure steps to correct the condition.

FORD · 2018-10-05

Some 2018 F-150 vehicles equipped with a 2.7L EcoBoost built on or before 12-Jul-2018 with greater than 500 miles may exhibit an illuminated Malfunction Indicator Lamp (MIL) with diagnostic trouble codes (DTC) P0300, P0316, P0301-P0306, P2196, P2198, P0171, P0174, P219A, P219B, P0172 and/or P0175 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.

CADILLAC, CHEVROLET, GMC · 2018-01-18

This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.

FORD · 2017-02-15

SOME 2015 TRANSIT VEHICLES BUILT ON OR BEFORE 30-MAR-2015 MAY EXHIBIT VARIOUS DRIVABILITY CONCERNS INCLUDING DIFFICULTY STARTING, MISFIRES AND/OR AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODE (DTC) P00BD, P1247, P1548, P061B, P2195, P2198, P2196, P2197, P0171, P0172, P0174, P0175, P0131 AND/OR P162F STORED IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY. THIS MAY BE DUE TO UNDESIRED WATER ENTRY INTO THE ENGINE COMPARTMENT DIRECTLY OVER POWERTRAIN COMPONENTS. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

BUICK, CADILLAC, CHEVROLET, GMC · 2016-11-30

This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.

LEXUS · 2015-12-17

TT: TMS has discovered the current engine active test ?Control the Injection Mode? is not operating as desired when controlling the direct injectors manually on 2GR-FKS or 8AR-FTS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. In order to avoid this condition, technicians should raise engine RPM when changing from Direct Injection active test to Port Injection active test. Use the recommended procedure below to avoid this concern while testing injection mode of 2GR-FKS or 8AR-FTS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel…

LEXUS · 2015-12-17

"TT: TMS HAS DISCOVERED THE CURRENT ENGINE ACTIVE TEST “CONTROL THE INJECTION MODE” IS NOT OPERATING AS DESIRED WHEN CONTROLLING THE DIRECT INJECTORS MANUALLY ON 2GR-FKS OR 8AR-FTS ENGINES. WHEN DIRECT INJECTION IS STARTED AND THEN STOPPED USING THE ACTIVE TEST, CURRENT ECU LOGIC DOES NOT TURN OFF THE DIRECT INJECTORS AND CAN CAUSE DTCS P017200, P017500 AND P0160300. IN ORDER TO AVOID THIS CONDITION, TECHNICIANS SHOULD RAISE ENGINE RPM WHEN CHANGING FROM DIRECT INJECTION ACTIVE TEST TO PORT INJECTION ACTIVE TEST. USE THE RECOMMENDED PROCEDURE BELOW TO AVOID THIS CONCERN WHILE TESTING INJECTION MODE OF 2GR-FKS OR 8AR-FTS EQUIPPED VEHICLES. NOTE: IF THE ACTIVE TEST IS USED MULTIPLE TIMES WITHOUT USING THIS PROCEDURE TO RAISE ENGINE RPM, IT MAY BE NECESSARY TO RESET LEARNING VALUES FOR FUEL…

TOYOTA · 2015-12-07

TT: TMS has discovered the current engine active test ?Control the Injection Mode? is not operating as desired when controlling the direct injectors manually on 2GR-FKS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. In order to avoid this condition, technicians should raise engine RPM when changing from Direct Injection active test to Port Injection active test. Use the recommended procedure below to avoid this concern while testing injection mode of 2GR-FKS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel trim and Air to Fuel…

TOYOTA · 2015-12-07

"TT: TMS HAS DISCOVERED THE CURRENT ENGINE ACTIVE TEST “CONTROL THE INJECTION MODE” IS NOT OPERATING AS DESIRED WHEN CONTROLLING THE DIRECT INJECTORS MANUALLY ON 2GR-FKS ENGINES. WHEN DIRECT INJECTION IS STARTED AND THEN STOPPED USING THE ACTIVE TEST, CURRENT ECU LOGIC DOES NOT TURN OFF THE DIRECT INJECTORS AND CAN CAUSE DTCS P017200, P017500 AND P0160300. IN ORDER TO AVOID THIS CONDITION, TECHNICIANS SHOULD RAISE ENGINE RPM WHEN CHANGING FROM DIRECT INJECTION ACTIVE TEST TO PORT INJECTION ACTIVE TEST. USE THE RECOMMENDED PROCEDURE BELOW TO AVOID THIS CONCERN WHILE TESTING INJECTION MODE OF 2GR-FKS EQUIPPED VEHICLES. NOTE: IF THE ACTIVE TEST IS USED MULTIPLE TIMES WITHOUT USING THIS PROCEDURE TO RAISE ENGINE RPM, IT MAY BE NECESSARY TO RESET LEARNING VALUES FOR FUEL TRIM AND AIR TO FUEL…

TOYOTA · 2014-12-11

TSB: Some 2012 ? 2015 model year Sequoia and Tundra vehicles with the 3UR-FBE engine may exhibit a MIL ?ON? condition with Diagnostic Trouble Codes (DTCs) P0171/P0174 (System too Lean Bank 1/Bank 2), P0172/P0175 (System too Rich Bank 1/Bank 2), P1604 (Startability Malfunction), and/or P1605 (Rough Idling) after attempting to start the engine. Alcohol Density Estimate values may be high even though the vehicle was fueled with regular fuel (E0/E10). The Engine Control Module/ECM (SAE term: Powertrain Control Module/PCM) logic has been modified to address this condition. Use the following Repair Procedure to reprogram the ECM (PCM). ©