P1CA0 · نشرات الشركة المصنعة

MERCEDES-BENZ, MERCEDES-MAYBACH · 2026-07-01

Complaint The trunk lid does not open or close completely and must be operated manually by the customer. The following fault codes are stored in the PTCM control unit: • P1CA000 • B188C2A Cause If the trunk lid is repeatedly opened manually or the vehicle has experienced undervoltage, the trunk lid loses its normalization due to faulty software coding. Remedy For vehicles with a production date up to 01/22/26 (SL (232)) or 01/27/26 (GT (192)) 1. Update the HKS N121/1 control unit and perform SCN coding. (If no new software is available, still perform SCN coding) 2. Perform normalization of component 'N121/1 (Liftgate control control unit)'. Vehicles produced from January 22, 2026 (SL (232)) and January 27, 2026 (GT (192)) onward were factory-fitted with the correct Software Calibration…

MERCEDES-BENZ · 2026-03-11

Complaint 243: Red 12V battery message, white HV warning message, warning message in the IC and if applicable for vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored in the same ignition cycle, additional warning messages, e.g. red HV warning message and yellow HV drive system warning message may be shown. The DC/DC converter has stored a combination of the following two fault code groups: 1. P0C3B00, P0E9700, P0E5400, P0C4000. 2. P1D0B00, P1CA000, U011500. In some cases, not all DTCs from one of these groups are triggered. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. This triggers the yellow HV drive…

MERCEDES-BENZ, MERCEDES-MAYBACH · 2026-03-09

Complaint The trunk lid does not open or close completely and must be operated manually by the customer. The following fault codes are stored in the Tailgate Control (HKS) control unit: P1CA000 & B188C2A Cause If the trunk lid is repeatedly opened manually or the vehicle has experienced undervoltage, the trunk lid loses its normalization due to faulty software coding. Remedy For vehicles with a production date up to 01/22/26 (232) or 01/27/26 (192): Update the HKS N121/1 control unit and perform SCN coding. • If no new software is available, perform SCN coding. Vehicles with a production date 01/22/2026 (232) or 01/27/2026 (192) and later have already received the correct QNT from the factory.

MERCEDES-BENZ · 2026-02-14

Complaint 243: Red 12V battery message, white HV warning message, warning message in the IC and if applicable for vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored in the same ignition cycle, additional warning messages, e.g. red HV warning message and yellow HV drive system warning message may be shown. The DC/DC converter has stored a combination of the following two fault code groups: 1. P0C3B00, P0E9700, P0E5400, P0C4000. 2. P1D0B00, P1CA000, U011500. In some cases, not all DTCs from one of these groups are triggered. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. This triggers the yellow HV drive…

MERCEDES-BENZ · 2025-09-16

Complaint 243: Red 12V battery message, white HV warning message, warning message in the IC and if applicable for vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored in the same ignition cycle, additional warning messages, e.g. red HV warning message and yellow HV drive system warning message may be shown. The DC/DC converter has stored a combination of the following two fault code groups: 1. P0C3B00, P0E9700, P0E5400, P0C4000. 2. P1D0B00, P1CA000, U011500. In some cases, not all DTCs from one of these groups are triggered. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. This triggers the yellow HV drive…

MERCEDES-BENZ · 2025-08-08

Complaint: 243: Red 12V battery message, white HV warning message, warning message in the IC ​​and if applicable for vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored, additional further warning messages (e.g. red HV warning message and yellow HV drive system warning message) are displayed. The DC/DC converter has saved the four following fault codes at most: P0C3B00, P0E9700, P0E5400, P0C4000. In some cases, not all of these DTCs are triggered. The following DTCs either be triggered additionally or, in rare cases, without the previous DTCs: P1D0B00, P1CA000, U011500. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00…

MERCEDES-BENZ · 2025-08-05

Complaint: 243: Red 12V battery message, white HV warning message, warning message in the IC ​​and if applicable for vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored, additional further warning messages (e.g. red HV warning message and yellow HV drive system warning message) are displayed. The DC/DC converter has saved the four following fault codes at most: P0C3B00, P0E9700, P0E5400, P0C4000. In some cases, not all of these DTCs are triggered. The following DTCs either be triggered additionally or, in rare cases, without the previous DTCs: P1D0B00, P1CA000, U011500. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00…

MERCEDES-BENZ, MERCEDES-MAYBACH · 2025-04-11

Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Test: Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Reset the HOSWD control unit in line with the guided test in Xentry. Using both hands,…

MERCEDES-BENZ, MERCEDES-MAYBACH · 2025-02-03

Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy:…

MERCEDES-BENZ, MERCEDES-MAYBACH · 2025-01-06

Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy:…

MERCEDES-BENZ, MERCEDES-MAYBACH · 2024-07-15

Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy:…