P2048 · نشرات الشركة المصنعة

RAM · 2026-02-26

Malfunction Indicator Lamp (MIL) Illuminated, Diagnostic Trouble Codes (DTCs) P208B, P2D1F, P218F, P202E, P2048, P20E8, Setting In The Powertrain Control Module (PCM)

MAZDA · 2021-06-29

MSP58 - DOSING CONTROL UNIT REPROGRAMMING. On the subject CX-5 vehicles, diagnosis for the Selective Catalytic Reduction (SCR) system failure may not function properly, leading to an inappropriate/delayed failure detection of the Dosing Control Unit (DCU), with codes DTC P2048 and DTC P229F. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP) on certain 2019 CX-5 Diesel-fueled vehicles produced from March 23, 2018 through July 31, 2019. DTC P2048:00 - Urea injector circuit low input. Normally the diagnosis of urea injector coil resistance activates while the injector is operating and detects a failure based on the electric current value in the injector coil. On the subject vehicles, the diagnosis activates also while the injector is not operating due to…

VOLVO · 2021-06-16

Volvo Chassis - Model VNR With RH Side Fairing Only - Heat/Splash Shield Loose, Possible DTC P204800 And/Or P204713

VOLVO · 2021-05-25

Volvo Chassis - Model VNR With RH Side Fairing Only - Heat/Splash Shield Loose, Possible DTC P204800 And/Or P204713

NISSAN · 2020-02-05

2016 – 2019 TITAN XD; MIL ON WITH DTC P2048 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NISSAN · 2019-02-28

2016 ? 2018 TITAN XD; MIL ON WITH DTC P2048 STORED This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON and DTC P2048 (REDUCTANT INJECTION VALVE CIRCUIT LOW 1/1) is stored. ACTION Reprogram the ECM per the SERVICE PROCEDURE in this bulletin. - Refer to SERVICE PROCEDURE on the next page to confirm if reprogramming is needed. - Save Computer Data with CONSULT-III plus (C-III plus). - If this bulletin applies, continue with ECM Reprogramming procedure. - Write Saved Data with CONSULT-III plus.

NISSAN · 2016-05-31

IF YOU CONFIRM The MIL is ON with one or more of the following DTCs stored: * P020A - F: Cylinder 1 - 6 Injection Timing * P021A - B: Cylinder 7 - 8 Injection Timing * P060C: Internal Control Module Main Processor Performance * P061B: Internal Control Module Torque Calculation Performance * P0605: ECM * P2048: Reductant Injector Circuit Low * P0299: Boost Pressure * P2263: Turbocharger Boost System Performance * P0401: Flow in the Exhaust Gas Recirculation (Insufficient) * P0402: Flow in the Exhaust Gas Recirculation (Excessive) * P2483: Exhaust Gas Temperature Sensor Circuit Intermittent 1/5 * P244D: Exhaust Temperature Too High For PF Regeneration * U0415: VDC CAN CIR2 * P2BAD: NOx Concentration Exceeded * P1C55: NOx Sensor 1/1 Intermittent * P1C56: NOx Sensor 1/2 Intermittent * P2201:…

NISSAN · 2016-04-07

IF YOU CONFIRM The MIL is ON with one or more of the following DTCs stored. • P020A - F: Cylinder 1 – 6 Injection Timing • P021A - B: Cylinder 7 – 8 Injection Timing • P060C: Internal Control Module Main Processor Performance • P2048: Reductant Injector Circuit Low • P207F: Reductant Quality Performance • P2263: Turbocharger Boost System Performance ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

NISSAN · 2016-04-05

2016 TITAN XD; MIL ON WITH ENGINE DTCs STORED IF YOU CONFIRM The MIL is ON with one or more of the following DTCs stored. „h P020A - F: Cylinder 1 ¡V 6 Injection Timing „h P021A - B: Cylinder 7 ¡V 8 Injection Timing „h P060C: Internal Control Module Main Processor Performance „h P2048: Reductant Injector Circuit Low „h P207F: Reductant Quality Performance „h P2263: Turbocharger Boost System Performance ACTION 1. Save Computer Date with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Date with CONSULT-III plus.