P2127 · نشرات الشركة المصنعة

FORD · 2026-07-27

Some 2025-2026 Bronco/Ranger vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2122, P2123, P2127, P2128, and/or P2138 stored in the powertrain control module (PCM). The vehicle may or may not exhibit a perceived lack of power intermittently. This may be due to an issue with the following connectors associated with the accelerator pedal position (APP) sensor circuits: -C115B -C175B -C2040 Replacement of the accelerator pedal may not resolve this concern. Perform a wiggle test of the connectors while the engine is at normal operating temperature. Perform a visual inspection of the connectors as well as a terminal fit test using the appropriately sized flex probe. Repair as necessary. Refer to Wiring Diagram Cell 005. If no…

FORD · 2025-02-12

Some 2023-2025 F-Super Duty vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2122, P2123, P2127, P2128, and/or P2138 stored in the powertrain control module (PCM).

FORD · 2024-10-08

Some 2021-2024 F-150 non-Lightning vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2122, P2123, P2127, P2128, and/or P2138 stored in the powertrain control module (PCM).

FORD · 2024-04-05

Some 2023-2024 F-Super Duty vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2122, P2123, P2127, P2128, and/or P2138 stored in the powertrain control module (PCM). The vehicle may or may not exhibit a perceived lack of power intermittently. Perform a wiggle test of connector C1580 at the left rear of the engine compartment while the engine is at normal operating temperature. Perform a visual inspection of pins 18 through 29 as well as a terminal fit test using the appropriately sized flex probe. Repair as necessary. Refer to Wiring Diagram Cell 005. If no concerns are found, refer to Workshop Manual (WSM), Section 310-02 for normal diagnostics.

RAM · 2023-11-18

Malfunction Indicator Lamp (MIL) On, Electronic Throttle Control (ETC) Lamp Flashes, Diagnostic Trouble Code (DTC) P2127 Accelerator Pedal Position Circuit Low

FORD · 2021-10-29

Some 2020-2021 Escape vehicles may exhibit various symptoms due to a loss of voltage reference (VREF) from the 14290 harness above the steering shaft u-joint. Possible symptoms may include an illuminated malfunction indicator lamp (MIL),runs rough, fuse 44 open and may or may not set DTCs P06A7, P0840, P0842, P0845, P0847, P2122, P2127, P0522, P008A, P06A6, P2196, P0192, P0369, P0212, P0340, P0344, P0365, P0532,P0504, P07E4, P06E9, P0369, C175E, C175B, C2302, and/or C0040. Inspect the 14290 harness directly above the steering shaft u-joint near the upper brake pedal mount that may come in contact with the steering shaft. Rotation of the steering wheel may cause the short circuit. If damage is found, repair as necessary and move the harness away from the steering shaft U-joint area and…

FORD · 2021-09-14

Some 2020-2021 Escape vehicles may exhibit a loss of voltage reference (VREF) or runs rough, blow fuse 44 and may or may not set DTC's P06A7,P0840,P0842,P0845,P0847,P2122,P2127,P0522,P008A,P06A6,P2196,P0192, P0212,P0340,P0344,P0365,P0532,P06E9,P0369,C175E,C175B,C2302,P0369. The 14290 harness directly above the steering shaft u-joint near the upper brake pedal mount may come in contact with the steering shaft. Rotation of the steering wheel will trigger the short circuit. Inspect the harness for damage at that location and repair as necessary. If damage was found, move the harness away from the steering shaft U-joint area and secure the harness. Refer to Wiring Diagram Cell 005.

RAM · 2020-02-26

PEDAL, Accelerator (APPS) Before replacing accelerator pedal for P061B, make sure all PCM software service bulletins and recalls are up to date, if applicable. Before replacing accelerator pedal for other DTCs, be sure to follow fault code diagnostic procedures in Service Library and be sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and acceleartor pedal should not be replaced for this fault if driving style is confirmed with the customer.

CHRYSLER · 2020-02-26

PEDAL, Accelerator Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in Service Library and be sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault if driving style is confirmed with the customer.

FORD · 2018-11-08

Some 2018-2019 F-Super Duty vehicles equipped with a 6.7L engine built on 1-Dec-2017 and through 1-Aug-2018 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P2122, P2127, U0401, U0109, P0480, P008A, P025C, P027A and/or P064A. This may be due to powertrain control module (PCM) connector C1232B not being properly seated to the PCM.

FORD · 2018-07-26

Some 2018 F-Super Duty vehicles equipped with a 6.7L engine built on 1-Dec-2017 and through 8-Jul-2018 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P2122, P2127, U0401, U0109, P0480, P008A, P025C, P027A and/or P064A. This may be due to powertrain control module (PCM) connector C1232B not being properly seated to the PCM.

FORD · 2018-02-20

Some 2012-2014 Focus vehicles equipped with a 2.0L gasoline direct injection (GDI) engine may exhibit concerns of engine runs rough, crank no-start, loss of power, loss of engine RPM, and/or illuminated MIL with diagnostic trouble codes (DTCs) P0122, P0222, P0320, P0322, P0327, P0332, P0344, P0369, P06A7, P060D, P061C, P1336, P1674, P2111, P2112, P2127 and/or P2135. Follow the Service Procedure steps to correct the condition.

FORD · 2017-10-23

Some 2017 F-Super Duty vehicles built on or before 28-Aug-2017, may exhibit an intermittent loss of throttle pedal response, illuminated wrench, hill descent, airbag, anti-lock brake system (ABS) and/or advanced trac warning indicators and/or P2122, P2123, P2124, P2125, P2127, P2128, and/or P2138 DTCs. This may be caused by the Accelerator Pedal Position (APP) sensor 14A005 harness being improperly routed behind the brake booster to brake pedal bracket. If the harness is improperly routed, loosen the bracket to free the harness, refer to Workshop Manual (WSM), section 206-06 and inspect for any damaged circuits. If the harness is properly routed, proceed with normal diagnostics.

FORD · 2017-09-20

Some 2015-2017 F-150 vehicles may experience intermittent loss of throttle pedal response, illuminated wrench, hill descent, airbag, anti lock brake system(ABS) and/or advanced trac warning indicators and/or P2122, P2123, P2124, P2125, P2127, P2128 and/or P2138 DTCs. This may be caused by the Accelerator Pedal Position (APP) Sensor 14A005 harness being improperly routed behind the brake booster to brake pedal bracket. If the harness is improperly routed, loosen the bracket to free the harness, refer to Workshop Manual (WSM), Section 206-06. Inspect and repair damaged circuits before properly routing the harness. If the harness is properly routed, proceed with normal diagnostics.

ALFA ROMEO, CHRYSLER, DODGE, FIAT, JEEP, RAM, SRT · 2017-06-14

Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

ALFA ROMEO, CHRYSLER, DODGE, FCA, FIAT, JEEP, RAM, SRT · 2017-06-14

Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

FORD · 2016-12-09

SOME 2014-2016 TRANSIT CONNECT VEHICLES EQUIPPED WITH THE 2.5L ENGINE MAY EXHIBIT A CONSTANT OR INTERMITTENT ILLUMINATED MIL WITH VARIOUS DRIVABILITY ISSUES AND ONE OR MORE OF THE FOLLOWING DTCS: P0010, P0103, P0104, P0122, P0131, P0135, P0137, P0141, P0201-P0204, P0217, P0222, P0223, P025A, P0300, P0301-P0304, P0316, P0351-P0354, P0400, P0403, P0443, P1285, P1289, P128A, P1299, P2101, P2107, P2111, P2112, P2122, P2127 AND/OR U0109. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

FORD · 2016-10-19

SOME 2015-2016 F-150 VEHICLES MAY EXPERIENCE INTERMITTENT LOSS OF THROTTLE PEDAL RESPONSE, ILLUMINATED WRENCH, HILL DESCENT, AIRBAG, ANTI LOCK BRAKE SYSTEM(ABS) AND/OR ADVANCED TRAC WARNING INDICATORS AND/OR P2122, P2123, P2124, P2125, P2127, P2128 AND/OR P2138 DTCS. THIS MAY BE CAUSED BY THE ACCELERATOR PEDAL POSITION (APP) SENSOR 14A005 HARNESS BEING IMPROPERLY ROUTED BEHIND THE BRAKE BOOSTER TO BRAKE PEDAL BRACKET. IF THE HARNESS IS IMPROPERLY ROUTED, LOOSEN THE BRACKET TO FREE THE HARNESS. INSPECT AND REPAIR DAMAGED CIRCUITS BEFORE PROPERLY ROUTING THE HARNESS. IF THE HARNESS IS PROPERLY ROUTED, PROCEED WITH NORMAL DIAGNOSTICS IN THE WORKSHOP MANUAL (WSM).

CHRYSLER · 2016-01-20

Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

CADILLAC, CHEVROLET, GMC · 2015-10-29

This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp on or reduced power message. Technician may find Diagnostic Trouble Codes P0106, P0107, P0697, P2122, P2123, P2127, P2128 and P2138. Technician should follow published Service Information diagnostics for the Diagnostic Trouble Codes that have set, if it is inconclusive inspect the wiring harness near the left instrument panel junction block. Technician will need to repair the damaged wiring.

CADILLAC, CHEVROLET, GMC · 2014-07-16

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on or reduced engine power message. Technician may find Diagnostic Trouble Codes P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138. Technician will need to inspect the Accelerator Pedal Position circuits for poor terminal tension.

FORD · 2014-01-01

FORD: IN BATTERY JUNCTION BOX, IS A DAMAGED OR AN IMPROPERLY SEATED CONNECTOR, CAUSING CHECK ENGINE LIGHT TO ILLUMINATE, WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2122, P2127 AND/OR 02138. MODEL 2012-2013 FOCUS, 2013 ESCAPE. *PE

HINO · 2013-07-03

13-004 CORRECTION OF 2013MY WORKSHOP MANUAL. There are two different troubleshooting methods for DTC P2122, P2123, P2127 and P2128 in the the workshop manual. (One is the check sheet type, and the other one is the flow chart.) The troubleshooting methods of the check sheet type for these DTCs are insufficient. Therefore, please refer the troubleshooting ?flow chart? when you perform trouble diagnosis for these DTCs. Please refer to the page 2/3-3/3 for the details.

CADILLAC · 2013-02-01

This Preliminary Information communication provides information to the technician about vehicles that have Service Stabilitrak Message being displayed in the driver?s information center. Technician may find Diagnostic Trouble Code P1153, P1133, P1826, P1827, P2120, P2122, P2123, P2125, P2127, P2128, and P2138. Technician will need to inspect X104 to be rubbing on the cylinder head. Technician will repair any damaged wires and reroute the wire harness.

SAAB · 2010-08-01

SAAB: ACCELERATOR PEDAL POSITION SENSOR DTCS SET IN ECM 2003-2009 SAAB. APP SENSOR DTC'S OF P2122-00, P2123-00, P2126-00, P2127-00, P2128-00, AND/OR P2138-00 IN THE ECM. THESE DTC'S MAY BE VERY INTERMITTENT AND ARE DIFFICULT TO REPRODUCE. THE APP SENSOR, T8, AND/OR ENGINE HARNESS MAY HAVE BEEN REPLACED WITH NO CHANGE TO THE CONDITION. *PE

HYUNDAI · 2010-07-01

HYUNDAI: CHECK ENGINE LIGHT P2138, P2127, P2122 DTC WITH P2106. REPLACE THE ACCELERATOR PEDAL SENSOR ASSEMBLY. *PE

CHRYSLER, DODGE · 2010-02-16

CHRYSLER/DODGE: ETC LIGHT ILLUMINATED OR DIAGNOSTIC TROUBLE CODE P2122 AND/OR P2127 SET. THIS BULLETIN INVOLVES DISCONNECTING THE WIRE HARNESS CLIP NEAR THE ETC SENSOR. SOME CUSTOMERS MAY EXPERIENCE AN ETC LIGHT ILLUMINATION. UPON FURTHER INSPECTION THE DTC'S P2122-ACCELERATOR PEDAL POSITION SENSOR 1 CIRCUIT LOW AND/OR P2127-ACCELERATOR PEDAL POSITION SENSOR 2 CIRCUIT LOW HAVE BEEN SET. THIS CONDITION COULD BE CAUSED BY THE WIRING TO THE APP SENSOR BEING HELD TOO TIGHT, CAUSING THE WIRING TO BECOME LOOSE RESULTING IN THE ETC LIGHT ILLUMINATION. MODELS TOWN AND COUNTRY/GRAND CARAVAN. *PE

CHRYSLER, DODGE · 2010-02-08

DODGE: ETC LIGHT ILLUMINATED OR DIAGNOSTIC TROUBLE CODE P2122 AND/OR P2127 SET. VEHICLES EQUIPPED WITH POWER ADJUSTING PEDALS OR POWER ADJUSTING PEDALS WITH MEMORY (SALES CODE XPP OR XAM) MAY HAVE BEEN BUILT WITH THE WIRING TO THE APP SENSOR BEING HELD TOO TIGHT. MODELS GRAND CARAVAN/TOWN AND COUNTRY. *PE

CADILLAC, CHEVROLET, GMC · 2008-11-19

GMC: EI08047-INTERMITTENT MIL/SES, DTC(S) P2120, 02122, 02123, 02125, P2127, P2128, P2138 WITH REDUCED ENGINE POWER (REPLACE ACCELERATOR PEDAL). THIS MAY BE CAUSED BY CORROSION AT THE ACCELERATOR PEDAL CONNECTOR. *PE

CADILLAC, CHEVROLET, GMC · 2008-03-01

EI08047 - INTERMITTENT MIL/SES, DTC'S P2120, P2122, P2123, P2125, P2127, P2128, P2138 WITH REDUCED ENGINE POWER. *NJ