RAM

18-031-25 REV. C

2025-10-22 · NHTSA 11024560

A listed vehicle is a research lead. Confirm the engine, production range and software in the manufacturer's information.

Manufacturer summary

Original wording in English

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. ● P0071-00 - Ambient Air Temperature Sensor Performance. ● P2C90-00 - Crankcase Ventilation System - Hose "A" Disconnected. ● P1CEA-00 - Boost Side EVAP Purge System Performance. ● P05BD-00 - Stop-start Mode Switch Range/Performance. ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. ● U0673-00 - Lost Communication With Ion Sense Module.** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking - in ACTIVE or STORED status. ● P0325-00 - Knock/Combustion Vibration Sensor 1 Circuit - in ACTIVE or STORED status. ● P0330-00 - Knock/Combustion Vibration Sensor 2 Circuit - in ACTIVE or STORED status. ● P032A-00 - Knock-Combustion Vibration Sensor C Circuit - in ACTIVE or STORED status. ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/Performance - in ACTIVE or STORED status. ● P2AF6-00 - Starter Relay 3 Stuck Off - in ACTIVE or STORED status. ● P0300-00 - Multiple Cylinder Misfire - in ACTIVE or STORED status set during cold start catalyst heating. ● P0301-00 - Cylinder 1 Misfire - in ACTIVE or STORED status set during cold start catalyst heating. ● P0302-00 - Cylinder 2 Misfire - in ACTIVE or STORED status set during cold start catalyst heating. ● P0303-00 - Cylinder 3 Misfire - in ACTIVE or STORED status set during cold start catalyst heating. ● P0304-00 - Cylinder 4 Misfire - in ACTIVE or STORED status set during cold start catalyst heating. ● P0305-00 - Cylinder 5 Misfire - in ACTIVE or STORED status set during cold start catalyst heating. ● P0306-00 - Cylinder 6 Misfire - in ACTIVE or STORED status set during cold start catalyst heating. NOTE: To confirm the cold start catalyst heating, use WiTech Freeze Frame data, and confirm "Time Since Engine Start" less than 30 seconds and "Engine Coolant Temperature °F" less than 50 °C (122 °F) when Misfire Code was set. See Step 3 for more details. ● U0104-00 - Lost Communication With Cruise Control Module - in ACTIVE or STORED status. This software update will allow this permanent fault code to naturally clear. ● U0405-00 - Invalid Data Received From Cruise Control Module - in ACTIVE or STORED status. This software update will allow this permanent fault code to naturally clear. Customers may also experience one or more of the following: ● **Rough running engine. ● "Excessive Oil - Service Vehicle" message display in the Instrument Panel Cluster (IPC). ● Vehicle is difficult to start. ● Potential stalling when coming to a stop with an immediate restart. NOTE: If the engine were to stall while stopping, a message would display in the IPC informing the driver to shift to Park to restart the engine.* This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.

Repeated filings are grouped only when make, bulletin number, publication date and complete summary agree. Original record numbers are retained. Older publications remain available, and an explicit later version is shown when established. Pre-1994 vehicle associations are separated from default results; an unspecified year does not mean all model years apply.