P0394 · Herstellerinformationen

JEEP · 2020-10-28

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find oneor more of the following Diagnostic Trouble Codes (DTCs).P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0344 - Camshaft Position Sensor Intermittent. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 -…

JEEP · 2020-10-28

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0344 - Camshaft Position Sensor Intermittent. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 -…

CHRYSLER · 2019-05-04

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. A customer or technicians may be unable to read data information from the OBDII connector when using a generic scan tool (APAC).Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following DTCs have been set (NAFTA):U0418 - Implausible Data Received From Brake System Control Module 1. U0432 - Invalid Data Received From Multi-Axis Acceleration Sensor Module. P06EF - Engine Restart Performance. P06E9 - Engine Starter Performance. P00FD - Battery -B- State Of Charge Performance. C2222-68 - Improper Powerdown - Event Information. P0607-00 - ECU Internal Performance - ESM. U0402-00 -…

FORD · 2018-12-03

Some 2018 F-150 and 2018-2019 Mustang vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with DTCs P0390 and/or P0394 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.

FORD · 2018-08-02

Some 2018 F-150 vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with DTCs P0390 and/or P0394. These DTCs may be caused by low engine oil level. Before performing any diagnosis or repair, make sure the oil level is between the minimum and maximum marks on the oil level indicator. If the oil level is below the minimum mark, diagnose the low oil level concern first. Refer to the Workshop Manual, Section 303-00. If the oil level is in the normal operating range, inspect C1627. If no concerns are present, replace the bank 2 (LH) exhaust variable camshaft timing (VCT) solenoid. Do not replace camshaft position sensors for these DTCs. For claiming, use causal part 6M280 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.…

CHRYSLER · 2017-08-09

Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following DiagnosticTrouble Codes (DTCs) have been set:U1400-00 - Implausible TPS Signal Received P1D73 - AGS Performance -(Active Grill Shutter). P0171 - Fuel System 1/1 Lean. P0174 - Fuel System 2/1 Lean. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to atwo trip fault:P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent…

CHRYSLER, DODGE, FIAT, JEEP, RAM · 2015-08-04

Camshaft Position Sensor If replacing a camshaft position sensor for P0340, P0344, P0345, P0349, P0365, P0369, P0390 or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com