P0563 · Herstellerinformationen

MERCEDES-BENZ · 2026-08-25

Complaint Customers may report one or more of the following: • Transmission malfunction message • Check engine light illuminated • Shifts into N • Concern disappears after ignition cycle When performing a quick test, the following fault code is stored in Y3/14 ‐ Transmission control for 8‐speed dual‐clutch transmission (DKG): P056300 The on‐board power supply voltage is too high. Cause An overvoltage condition is detected exclusively within the transmission control unit, storing fault P056300 once the measured voltage exceeds 16V. Remedy This LI applies if the freeze frame data for P056300 show a supply voltage between 15.75 to 16.50 volts, and no other control units report overvoltage. (figure 1) Long Term Resolution: Software resolutions have been released. Check validity and ensure…

MERCEDES-BENZ · 2026-08-04

Complaint Customers may report one or more of the following: • Transmission malfunction message • Check engine light illuminated • Shifts into N • Concern disappears after ignition cycle When performing a quick test, the following fault code is stored in Y3/14 - Transmission control for 8-speed dual-clutch transmission (DKG): P056300 The on-board power supply voltage is too high. Cause An overvoltage condition is detected exclusively within the transmission control unit, storing fault P056300 once the measured voltage exceeds 16V. Remedy This LI applies if the freeze frame data for P056300 show a supply voltage between 15.75 to 16.50 volts, and no other control units report overvoltage. (figure 1) Long Term Resolution: Software resolutions are being rolled out for various models. Check…

JEEP · 2026-04-16

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst…

JEEP · 2026-04-16

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst…

JEEP · 2026-04-16

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst…

JEEP · 2026-01-24

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. **(Manual Transmission Only)** ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on the following: ● "Service Transmission” message on…

JEEP · 2025-07-18

Flash: Powertrain Control Module (PCM) Updates ustomers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P2504 - Charging System Output High. ● P0563 - Battery/System Voltage High. Customers may also experience one or more of the following: ● **Vehicle goes in limp mode within 1.6 km (1 mi) of driving while in 4LO, DTC P08A6 active and "Clutch Too Hot" message followed by "Service Transmission” message in the Instrument Panel Cluster (IPC).** ● The engine runs rough…

JEEP · 2025-07-09

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation.** ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 circuit high. ● P0152 - O2 Sensor 2/1 circuit high. ● P2504 - Charging system output high. ● P0563 - Battery/system voltage high. Customers may also experience the following: ● **"Service Transmission” message on in the Instrument Panel Cluster (IPC).** ● The engine runs rough. This bulletin involves reprogramming the PCM with the latest available software.

JEEP · 2025-07-09

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation.** ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● "Service Transmission”…

FORD · 2025-06-09

This article supersedes TSB 24-2163 to update the Service Procedure and change labor operation from actual to fixed time. Some of the vehicles listed in the Model statement above may exhibit an illuminated powertrain malfunction (wrench) indicator and/or "Stop Safely Now" message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F and/or P0C78 stored in the battery energy control module (BECM). The vehicle may also exhibit a low/discharged 12v battery. This may be due to the high voltage battery junction box.

JEEP · 2025-03-01

Flash: Powertrain Control Module (PCM) Updates "Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection…

CHEVROLET, GMC · 2025-01-15

This technical bulletin provides repair information to correct a customer concern of Silverado and Sierra Setting DTC P0606 and either DTC P0562 or P0563.

JEEP · 2024-09-05

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection…

JEEP · 2024-08-02

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High.** ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip…

CHEVROLET, GMC · 2024-08-01

This technical bulletin provides repair information to correct a customer concern of Silverado and Sierra Setting DTC P0606 and either DTC P0562 or P0563.

CHEVROLET, GMC · 2024-06-29

This technical bulletin provides repair information to correct a customer concern of Silverado and Sierra Setting DTC P0606 and either DTC P0562 or P0563.

JEEP · 2024-06-20

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P2504 - Charging System Output High. ● P0563 - Battery/system Voltage High (eTorque). Customers may also comment on the following: ● Customer finds Check Engine Light on and vehicle runs rough. This bulletin involves reprogramming the PCM with the latest available software."

FORD · 2024-05-25

This article supersedes TSB 24-2017 to update the Service Procedure and Parts List. Some 2021-2022 Mustang Mach-E vehicles built on or before 28-May-2022 may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F and/or P0C78 stored in the battery energy control module (BECM). It may also have a low/discharged 12V battery and/or display a Stop Safely Now message in the instrument panel cluster (IPC). This may be due to the high voltage battery junction box. To correct the condition, follow the Service Procedure to replace the high voltage battery junction box and reprogram the BECM.

JEEP · 2024-05-21

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0158 - O2 Sensor 2/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on due to Clutch Slip Detection with the transfer case in neutral. ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other Software Enhancements: ● Improvements to address vehicle no starts after replacing…

JEEP · 2024-05-03

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - closed loop fueling not achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 circuit high. ● P0152 - O2 Sensor 2/1 circuit high. ● P2504 - Charging system output high. ● P0563 - Battery/system voltage high. Customers may also experience the following: ● The engine runs rough. This bulletin involves reprogramming the PCM with the latest available software."

JEEP · 2024-05-03

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - closed loop fueling not achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 circuit high. ● P0152 - O2 Sensor 2/1 circuit high. ● P2504 - Charging system output high. ● P0563 - Battery/system voltage high. Customers may also experience the following: ● The engine runs rough. This bulletin involves reprogramming the PCM with the latest available software."

JEEP · 2024-05-02

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. This bulletin involves reprogramming the PCM with the latest available software."

CHEVROLET, GMC · 2024-03-11

This technical bulletin provides repair information to correct a customer concern of Silverado and Sierra Setting DTC P0606 and either DTC P0562 or P0563.

JEEP · 2023-11-22

Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0563-00 - System Voltage High. ? P21CC-00 - Reductant Control Module Supply Voltage High. ? P20F6-00 - Reductant Injection Valve Stuck Open Bank One Unit One. ? P208E-00 - Reductant Injector Stuck Closed - Bank One Unit One. ? P24B2-00 - Particulate Matter Sensor Circuit Intermittent. ? P00C0-00 - Turbocharger-Supercharger Bypass Valve Two Control Circuit. Customers may also comment on one or more of the following: ? **Vehicle not starting. ? Battery not charging. ? Engine oil Temp High message in the Instrument Panel Cluster (IPC). ?…

FORD · 2023-11-10

This article supersedes TSB 23-2257 to update the Parts List. Some 2021-2023 Mustang Mach-E vehicles built on or before 17-Mar-2023 may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F, and/or P0C78 stored in battery energy control module (BECM). It may also have a low/discharged 12V battery and/or display a Stop Safely Now message in the instrument panel cluster (IPC). This may be due to the high voltage battery junction box (HVBJB). To correct the condition, follow the Service Procedure to replace the HVBJB and reprogram the BECM.

FORD · 2023-08-22

Some 2021-2022 Mustang Mach-E vehicles built on or before 17-Mar-2023 may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F, and/or P0C78 stored in battery energy control module (BECM). It may also have a low/discharged 12V battery and/or display a Stop Safely Now message in the instrument panel cluster (IPC). This may be due to the high voltage battery junction box (HVBJB). To correct the condition, follow the Service Procedure to replace the HVBJB and reprogram the BECM.

JEEP · 2023-07-13

Flash: Hybrid Control Processor (HCP) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ?P0563-00 - System Voltage High. ? P2B28-00 - Hybrid/EV Battery Pack Coolant Pump Performance. Customers may also comment on one or more of the following: ? Reduced engine restart performance. ? May observe battery lamp illumination or the technician observes the 12V system voltage high when diagnosing. This bulletin involves reprogramming the HCP also known as Power Inverter Module (PIM) with the latest available software.

FORD · 2023-01-27

Some 2021-2022 Mustang Mach-E vehicles built on or before 28-May-2022 may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F, and/or P0C78 stored in battery energy control module (BECM). It may also have a low/discharged 12V battery and/or display a Stop Safely Now message in the instrument panel cluster (IPC). This may be due to the high voltage battery junction box (HVBJB). To correct the condition, follow the Service Procedure to replace the HVBJB and reprogram the BECM.

RAM · 2022-08-27

Flash: Hybrid Control Processor (HCP) Updates This bulletin involves updating the HCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) and/or Battery Charge Warning Light illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC). P0563-00 - System Voltage High.

FORD · 2022-08-02

Some 2021-2022 Mustang Mach-E vehicles built on or before 28-May-2022 may exhibit an illuminated malfunction indicator lamp (MIL) and/or display a Stop Safely Now message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F, and/or P0C78 stored in battery energy control module (BECM) or a low/discharged 12V battery with P0DA8 and/or P1A10 in the secondary onboard diagnostic module-C (SOBDMC). This may be due to the high voltage battery junction box (HVBJB). To correct the condition, follow the Service Procedure to replace the HVBJB and reprogram the BECM.