Ansehen

P0887 · Herstellerinformationen

Eine Fahrzeugzuordnung ist ein Recherchehinweis. Motor, Produktionszeitraum und Software anhand der Herstellerangaben prüfen.

P0887 ← Was bedeutet dieser Code?

37 Ergebnisse

SSM 51545 ↗

FORD · 2023-04-07

Some 2022-2023 F-150 Lightning vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) U3012, P062F, and/or P0A7F in the battery energy control module (BECM) and/or P0887 in the secondary on-board diagnostic control module-B (SOBDMB) or secondary on-board control module-C (SOBDMC). This may be due to a loose 12 volt positive or negative battery cable connection or loose ground connection. Prior to performing Workshop Manual (WSM) diagnostics, inspect both ends of the positive and negative battery cable connections and tighten if loose. Inspect connector C1168B and ground G127 for loose connections and tighten to 25 Nm (18 lb-ft). Refer to the Wiring Diagram for connector and ground locations. Perform the High Voltage Battery Capacity…

SSM 51094 ↗

FORD · 2022-09-22

Some 2022 F-150 Lightning vehicles may exhibit an illuminated malfunction indicator (wrench) lamp and/or malfunction indicator lamp (MIL) with diagnostic trouble code(s) (DTCs) U3012, P062F, and/or P0A7F in the battery energy control module (BECM) and/or P0887 in the secondary on-board diagnostic control module-B (SOBDMB), secondary on-board control module-C (SOBDMC). This may be due to a loose 12 volt positive or negative battery cable connection. Prior to performing Workshop Manual (WSM) diagnostics, inspect both ends of the positive and negative battery cable connections and tighten if loose. If the cable is tight, continue with normal workshop manual diagnostics. Be sure to use the Ford Diagnosis and Repair System (FDRS) high voltage battery capacity relearn. This routine must be…

2100821 ↗

CHRYSLER · 2021-03-12

Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P0732-00 - Gear 2 Shift Incorrect Ratio(Software Has Been Updated to Better Address This Concern). P0887-00 - TCM Power Control Circuit High. P1B13-00 - Park By Wire Unintended Out Of Park Position. P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. U0103-00 - Lost Communication With Electric Gear Shift Module. P1CC9 - Unable To Engage Gear. P1DDE-00 - Ignition Run/Start Input 1-2 Correlation. The customers may also experience the following:Harsh upshifts, 1-2,…

21-008-21 ↗

CHRYSLER · 2021-03-12

Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P0732-00 - Gear 2 Shift Incorrect Ratio(Software Has Been Updated to Better Address This Concern). P0887-00 - TCM Power Control Circuit High. P1B13-00 - Park By Wire Unintended Out Of Park Position. P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. U0103-00 - Lost Communication With Electric Gear Shift Module. P1CC9 - Unable To Engage Gear. P1DDE-00 - Ignition Run/Start Input 1-2 Correlation. The customers may also experience the following:Harsh upshifts, 1-2,…

2104417 ↗

FIAT · 2017-10-12

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:P0887 - TCM Power Control Circuit High.

21-033-17 REV. A ↗

FIAT · 2017-09-22

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P0887-00 - TCM Power Control Circuit High. P0901 - Clutch Actuator Circuit Range/Performance. U0001-00 - Can C Bus. U1412 - Implausible Vehicle Speed Signal Received.

21-043-17 ↗

JEEP · 2017-09-22

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following Diagnostic Trouble Codes (DTCs) have been set:U1412 - Implausible Vehicle Speed Signal Received. P0887 - TCM Power Control Circuit High. U0001 - Automatic Gearbox Shifter Module (AGSM) CAN Communication BUS (BUS Off). P0901 - Clutch 1 Actuator Control Circuit Performance. In addition, the following software enhancement is available:Changes which allow the catalytic convertor to operate cooler.

21-033-17 ↗

FIAT · 2017-09-21

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P0887-00 - TCM Power Control Circuit High. P0901 - Clutch Actuator Circuit Range/Performance. U0001-00 - Can C Bus. U1412 - Implausible Vehicle Speed Signal Received. The following enhancement is included in the software update:Introducing a switch, allowing the deactivation of aging function.

21-042-17 ↗

FIAT, JEEP · 2017-09-14

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P0887 - TCM Power Control Circuit High. P061B - Internal Control Module Torque Calculation Performance. P072F - Stuck In Fourth Gear. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance(2015 BU Only). P1CC9 - Unable to Engage Gear(2015 BU Only). P1D98 - Incorrect Gear Ratio Clutch B or D Defective(2015 BU Only). U0401 - Implausible Data Received From ECM-PCM(2015 BU Only). In addition, customers may notice the following condition(s):Harsh 1-2…

21-040-17 ↗

JEEP · 2017-09-13

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:P0887 - TCM Power Control Circuit High.

21-019-17 REV. A ↗

CHRYSLER, JEEP · 2017-09-09

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) withthe latest available software.A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination and/or one of the following conditions. Uponfurther investigation, a technician may find one or more of the following DTCs stored in the TCM memory.2015 KL VehiclesP1634-00 - TCM Internal Watchdog Performance(Sales Codes ED6 or ED8 Only).U1412- Implausible Vehicle Speed Signal Received. U0001- Can C Bus. P0887-00- TCM Power Control Circuit High. P061B-00- Internal Control Module Torque Calculation Performance. U0401-00- Implausible Data Received From ECM/PCM. P1DAD-00- Input Shaft-Output Shaft Direction Correlation. P0711-00- Transmission…

2101717 ↗

RAM · 2017-08-25

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTC:P0887 - TCM Power Control Circuit High. Enhancement also included:Improved calibrations for gear shifts.

2101817 ↗

RAM · 2017-08-11

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P1634 - TCM Internal Watchdog Performance. P0887 - TCM Power Control Circuit High. P1720 - Output Speed Sensor-Wheel Speed Rationality. P1DCCD - TCM Monitoring Processor Performance Multiple Clutches Locked Up. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. P1DAD - Input Shaft-Output Shaft Direction Correlation. P1CC9 - Unable To Engage Gear. This software release also includes the following improvements:Calibrations to support changes in air…

21-018-17 REV. A ↗

RAM · 2017-06-29

Flash: Transmission Shift and Driveability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P0887 - TCM Power Control Circuit High. P1720 - Output Speed Sensor-Wheel Speed Rationality. P1634 - Output Speed Sensor-Wheel Speed Rationality. P1DCCD - TCM Monitoring Processor Performance Multiple Clutches Locked Up. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. P1DAD - Input Shaft-Output Shaft Direction Correlation. P1CC9 - Unable To Engage Gear. In addition the following enhancements are…

21-006-17 REV. A ↗

JEEP · 2017-06-17

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:P0810-00 - Clutch Position Control Error - (Sales Codes EHK). P0887-00 - TCM Power Control Circuit High. U1424-00 - Implausible Engine Torque Signal Received. P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. Some customers may experience the following conditions:During a limp mode condition, the transmission remains in a fixed gear. 5-4 downshift hesitation. A longer than normal delay during a shift from reverse to drive selection. In…

21-011-17 ↗

JEEP · 2017-03-18

Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): U1412-00 - Implausible Vehicle Speed Signal Received. U0001 - CAN C BUS. P0887-00 - TCM Power Control Circuit High.

2103116 ↗

FIAT, JEEP · 2016-09-21

Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the TCM memory: P061B - Internal Control Module Torque Calculation Performance. P072F - Stuck In Gear 4. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (2015 BU only). P0887 - TCM Power Control Circuit High (2015 BU only). P1CC9 - Unable to Engage Gear (2015 BU only). P1D98 - Incorrect Gear Ratio Clutch B or D Defective (2015 BU only). U0401 - Implausible Data Received From ECM-PCM (2015 BU only).In addition, customers may experience…

21-021-15 REV-C ↗

CHRYSLER, JEEP · 2016-08-05

Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination and/or one of the following conditions. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the TCM memory. 2015 KL Vehicles · **When driving on grades, the 3-2 downshift is hard to achieve or not available (ED6).** · **P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (ED6).** · P0887-00 - TCM Power Control Circuit High. · U0401-00 - Implausible Data Received From ECM/PCM. · P1DAD - Input Shaft-Output Shaft Direction Correlation. 2015 UF…

21-016-16 ↗

JEEP · 2016-04-21

Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: · **P0887-00 - TCM Power Control Circuit High (Sales Codes ED6 and EHB). · P061B-00 - Internal Control Module Torque Calculation Performance (Sales Codes ED6 and EHB).** · P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. · P072F-00 - Stuck In Gear 4. · P076F-00 - Gear 7 shift Incorrect Ratio. · P0810-00 - Clutch Position Control Error. · P1CC9-00 - Unable To Engage Gear. · P0734-00 - Gear 4 Shift Incorrect…

21-016-16 ↗

JEEP · 2016-04-21

SYMPTOM/CONDITION: Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: • **P0887-00 - TCM Power Control Circuit High (Sales Codes ED6 and EHB). • P061B-00 - Internal Control Module Torque Calculation Performance (Sales Codes ED6 and EHB).** • P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. • P072F-00 - Stuck In Gear 4. • P076F-00 - Gear 7 shift Incorrect Ratio. • P0810-00 - Clutch Position Control Error. • P1CC9-00 - Unable To Engage Gear. • P0734-00 - Gear 4 Shift Incorrect Ratio. In addition, the following transmission shift and performance improvements are included in this software release: • **2-1 downshift quality…

21-015-16 ↗

CHRYSLER, JEEP · 2016-04-05

Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination and/or one of the following conditions. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the TCM memory. 2015 KL Vehicles · **P0887-00 - TCM Power Control Circuit High. · P061B-00 - Internal Control Module Torque Calculation Performance.** · U0401-00 - Implausible Data Received From ECM/PCM. · P1DAD- 00 - Input Shaft-Output Shaft Direction Correlation. · P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (ED6/ED8). Other enhancements…

21-015-16 ↗

CHRYSLER, JEEP · 2016-04-05

Flash: Transmission Diagnostic And Shift Enhancements. This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination and/or one of the following conditions. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the TCM memory. 2015 KL Vehicles P0887-00 - TCM Power Control Circuit High. P061B-00 - Internal Control Module Torque Calculation Performance.** U0401-00 - Implausible Data Received From ECM/PCM. P1DAD- 00 - Input Shaft-Output Shaft Direction Correlation. P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (ED6/ED8). Other enhancements included in this…

21-039-15 REV B ↗

RAM · 2015-11-20

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P1720 - Output Speed Sensor-Wheel Speed Rationality. ? P1634 - Output Speed Sensor-Wheel Speed Rationality. ? P1DCCD - TCM Monitoring Processor Performance Multiple Clutches Locked Up. ? P0887 - TCM Power Control Circuit High. ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. ? P1DAD - Input Shaft-Output Shaft Direction Correlation. ? P1CC9 - Unable To Engage Gear. In addition to the above…

21-016-15 REV. B ↗

JEEP · 2015-10-06

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a ?Stop/Start Ready? message in the Instrument Panel Cluster (IPC) when the vehicle did not perform an auto stop event. This message typically occurs while the vehicle is being driven in Snow Mode. In addition, a small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the TCM memory. ? P0887 - TCM Power Control Circuit High ? P1634 - TCM Internal Internal Watchdog Performance ? P061B - Internal Control Module Torque Calculation…

21-016-15 REV-B ↗

JEEP · 2015-10-06

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a ?Stop/Start Ready? message in the Instrument Panel Cluster (IPC) when the vehicle did not perform an auto stop event. This message typically occurs while the vehicle is being driven in Snow Mode. In addition, a small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the TCM memory. ? P0887 - TCM Power Control Circuit High ? P1634 - TCM Internal Internal Watchdog Performance ? P061B - Internal Control Module Torque Calculation…

21-021-15 REV. E ↗

CHRYSLER, JEEP · 2015-10-01

Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination and/or one of the following conditions. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the TCM memory. 2015 KL Vehicles ? When driving on grades, the 3-2 downshift is hard to achieve or not available (ED6). ? P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (ED6). ? P0887-00 - TCM Power Control Circuit High. ? U0401-00 - Implausible Data Received From ECM/PCM. ? P1DAD-00 - Input Shaft-Output Shaft Direction Correlation. 2015 UF Vehicles…

21-021-15 REV-E ↗

CHRYSLER, JEEP · 2015-10-01

Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination and/or one of the following conditions. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the TCM memory. 2015 KL Vehicles ? When driving on grades, the 3-2 downshift is hard to achieve or not available (ED6). ? P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (ED6). ? P0887-00 - TCM Power Control Circuit High. ? U0401-00 - Implausible Data Received From ECM/PCM. ? P1DAD-00 - Input Shaft-Output Shaft Direction Correlation. 2015 UF Vehicles…

21-039-15 REV-A ↗

RAM · 2015-08-22

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P1720 - Output Speed Sensor-Wheel Speed Rationality. ? P1634 - Output Speed Sensor-Wheel Speed Rationality. ? P1DCCD - TCM Monitoring Processor Performance Multiple Clutches Locked Up. ? P0887 - TCM Power Control Circuit High. ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. ? P1DAD - Input Shaft-Output Shaft Direction Correlation. ? P1CC9 - Unable To Engage Gear. In addition to the above…

21-021-15 REV-D ↗

CHRYSLER, JEEP · 2015-08-14

Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination and/or one of the following conditions. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the TCM memory. 2015 KL Vehicles ? When driving on grades, the 3-2 downshift is hard to achieve or not available (ED6). ? P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (ED6). ? P0887-00 - TCM Power Control Circuit High. ? U0401-00 - Implausible Data Received From ECM/PCM. ? P1DAD - Input Shaft-Output Shaft Direction Correlation. 2015 UF Vehicles ?…

21-032-15 REVA ↗

JEEP · 2015-07-15

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or describe harsh shifting. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) or symptoms. ? Harsh 1-2 Upshift. ? Harsh Garage Shifts (Park to Reverse or Drive). ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. ? P0887 - TCM Power Control Circuit High. ? P1CC9 - Unable to Engage Gear. ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective. ? U0401 - Implausible Data Received From ECM-PCM.