U3000 · Herstellerinformationen

MAZDA · 2020-06-23

Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's stored:à ̄‚· B119F:01 TCU - Tel antenna No. 1 malfunction à ̄‚· B119F:13 (TCU - TEL antenna No.1 circuit malfunction) à ̄‚· B119F:2B (CMU - GPS antenna signal circuit malfunction) à ̄‚· B1252:87 TCU - Communication error with connectivity master unit (CMU) à ̄‚· U0156:00 VCM - communication error with connectivity master unit (CMU) à ̄‚· U0156:00 BCM - Communication error with connectivity master unit (CMU) à ̄‚· U0198:00 BCM - Communication error with emergency call unit à ̄‚· U212D:00 BCM - Communication error with light control module (RH) à ̄‚· U3000:00 TCU - Telematics communication unit internal malfunction à ̄‚· Low…

MAZDA · 2020-06-05

Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's stored: à ̄‚· B119F:01 TCU - Tel antenna No. 1 malfunction à ̄‚· B1252:87 TCU - Communication error with connectivity master unit (CMU) à ̄‚· U0156:00 VCM - communication error with connectivity master unit (CMU) à ̄‚· U0156:00 BCM - Communication error with connectivity master unit (CMU) à ̄‚· U0198:00 BCM - Communication error with emergency call unit à ̄‚· U212D:00 BCM - Communication error with light control module (RH) à ̄‚· U3000:00 TCU - Telematics communication unit internal malfunction à ̄‚· Low Voltage Battery DTCs

FORD, LINCOLN · 2020-05-21

Some 2020 Escape/Corsair vehicles may exhibit a lack of power steering assist with DTC U3000 in the PSCM. This DTC is set when a battery charger is installed on the vehicle and the ignition is cycled on. For vehicles that set this DTC due to the use of a battery charger, the DTC can be cleared and power steering assist restored without replacement of the PSCM. To clear this DTC using the FDRS scan tool, select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. Once cleared, cycle the ignition to reinitialize the module. It is not recommended that a battery charger is installed and running on the vehicle when the ignition is cycled on.

FORD, LINCOLN · 2020-05-13

Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit a Front Camera Fault message and/or Collision Warning Not Available message with diagnostic trouble code (DTC) U3000:49 stored in the image processing module A (IPMA). This may be due to the software in the IPMA. To correct the condition, reprogram the IPMA using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

MAZDA · 2020-04-08

Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's stored: à ̄‚· B119F:01 TCU - Tel antenna No. 1 malfunction à ̄‚· B1252:87 TCU - Communication error with connectivity master unit (CMU) à ̄‚· U0156:00 VCM - Communication error with connectivity master unit (CMU) à ̄‚· U0156:00 BCM - Communication error with connectivity master unit (CMU) à ̄‚· U0198:00 BCM - Communication error with emergency call unit à ̄‚· U212D:00 BCM - Communication error with light control module (RH) à ̄‚· U3000:00 TCU - Telematics communication unit internal malfunction à ̄‚· Low Battery DTCs

MAZDA · 2020-02-25

Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's stored: B119F:01 TCU - Tel antenna No. 1 malfunction B1252:87 TCU - Communication error with connectivity master unit (CMU) U0156:00 VCM - Communication error with connectivity master unit (CMU) U0156:00 BCM - Communication error with connectivity master unit (CMU) U0198:00 BCM - Communication error with emergency call unit U212D:00 BCM - Communication error with light control module (RH) U3000:00 TCU - Telematics communication unit internal malfunction

FORD · 2019-12-06

Some 2020 Mustang vehicles built on or before 04-Sep-2019 may exhibit a U3000:62 DTC set in the PSCM. This may be accompanied by a slightly different steering feel, which will return to normal after one key cycle. To correct this condition, update the PSCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 3504 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

MAZDA · 2019-11-14

Some vehicles that have a drained battery recovered may exhibit that the engine will not start and the ignition switch will not turn off. The following DTC's may also be stored: à ̄‚· U3000:49 - BCM internal malfunction à ̄‚· B10E7:12 - IG1 relay circuit malfunction à ̄‚· P0615:11 - Starter relay circuit malfunction. This concern most likely occurs on vehicles in a show room with frequent door operation and poor battery maintenance. For proper battery maintenance of show room vehicles, refer to SA-043/19.

FORD · 2019-11-07

Some 2017-2019 F-Super Duty vehicles may exhibit a "Cruise Control Unavailable" or "Collision Avoidance Unavailable" message in the instrument cluster message center with diagnostic trouble code (DTC) U3000:49 in the cruise control module (CCM). Reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use base part 9E731, refer to Section 10 in the Service Labor Time Standards (SLTS) Manual.

JAGUAR · 2019-09-10

The Diagnostic Trouble Code (DTC) U3000-96 ? Component Internal Failure can be stored in the Image Processing Module B (IPMB) with no functional effect on the vehicle or camera system.

LAND ROVER · 2019-09-10

The Diagnostic Trouble Code (DTC) U3000-96 ? Component Internal Failure can be stored in the Image Processing Module B (IPMB) with no functional effect on the vehicle or camera system.

FORD, LINCOLN · 2019-06-20

Some 2015-2017 F-150/Mustang, 2015-2018 Edge/MKC, 2016-2018 MKX, 2013-2018 Explorer/Taurus/Flex/MKT, and 2017-2018 Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

FORD · 2019-05-14

Some 2017-2019 F-Super Duty vehicles may exhibit a diagnostic trouble code (DTC) U3000:49 in the cruise control module (CCM). A 'Pre-Collision Assist Not Available' or 'Adaptive Cruise Not Available' message may also be present in the instrument cluster message center. This DTC can set due to a low voltage battery state and may not indicate an internal fault within the CCM. Clear the DTC and perform a key cycle. If the DTC does not return after restarting the vehicle, do not replace the CCM. If a vehicle exhibits this concern, use the Report a Vehicle Concern link at the bottom of the OASIS tab and submit a report. Engineering is investigating. Monitor OASIS for updates.

MAZDA · 2019-03-28

If the right-side Blind Spot Monitoring (BSM) control module is replaced for any reason, it is also necessary to replace the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. Other possible symptoms that may be found if the right-side BSM module is replaced alone: BSM aiming fails, “BSM OFF" indicator ON, Center Display warning message, BSM failsafe (No operation), DTC U3000:54 stored in memory, DTC U1A4B:54 stored in memory (CX-3, MX-5 only).

MAZDA · 2019-03-22

Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction).Master Warning Light, Smart Brake Support/Smart City Brake Support (SBS/SCBS) Indicator Light, Lane-keep Assist System (LAS) Lane Departure Warning System (LDWS) Warning Light, High Beam Control (HBC) system Warning Light (amber). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

FORD, LINCOLN · 2019-03-12

Some 2017-2019 F-Super Duty, 2017-2019 Continental, 2016-2019 Edge, 2016-2018 MKX, 2019 Nautilus vehicles may exhibit a U3000:49 diagnostic trouble code (DTC) setting in the Steering Effort Control Module (SECM) with no other DTCs present. To eliminate the DTC, perform the IDS SASM module reset routine. The IDS reset routine is available under Toolbox > Chassis > Steering > Adaptive Front Steering > SASM Module Reset. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. For claiming, use causal part 3600 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

FORD · 2019-02-06

Some 2019 Transit Connect vehicles built on or after 28-May-2018 may experience a lack of power steering assist or a power steering fault message in the message center. It is important to avoid cycling the ignition switch. Charge the battery and remove the vehicle from transportation mode. If diagnostic trouble codes (DTCs) U3003 and U2011 are stored, attempt to recover the PSCM by performing module programming. If the vehicle has DTCs U3003, U3000, U2011 and the PSCM will not communicate with the diagnostic scan tool, replace the PSCM.

MAZDA · 2019-02-04

Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by an internal FSC failure. To eliminate this concern, the production process of the FSC has been modified.

JAGUAR · 2018-12-21

Message on the Instrument cluster stating "Air suspension not in customer mode" Diagnostic trouble code (DTC) U3000-05 logged in the Chassis Control Module (CHCM) Vehicle suspension is in tight tolerance mode

MAZDA · 2018-12-05

Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTC is stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. The combination of warning lights mentioned by the customer may include: SCBS/SBS, LAS/LDWS, HBC, Master Warning Light. Instrument Cluster Multi-Information Display (if equipped) warning messages may include: Forward Smart City Brake Support Malfunction, Smart Brake System Malfunction, Front Camera Sensor System Malfunction. MAZDA CONNECT center display warning messages may include: High Beam Control [HBC] / Lane-keep Assist System [LAS] Malfunction. Have the vehicle checked by a dealer if this indicator stays on. Smart City Brake Support [SCBS]…

MAZDA · 2018-11-27

Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The ?ROOM? fuse (Engine compartment) is NOT installed when battery level is low. 2. The CMU (Connectivity Master Unit) is NOT connected.

LAND ROVER · 2018-11-09

?SOS Limited Functionality? warning is displayed on the IC (Instrument Cluster along with Diagnostic Trouble Code (DTC) U3000-49 logged in the TCU (Telematics Control Unit). SOS Limited Functionality may affect the TCU's ability to support the ECall function when required by the customer.

LINCOLN · 2018-10-12

Some 2019 Edge and Nautilus vehicles may have a U3000:47 DTC set in the ABS module, with no other mechanical symptoms related to this DTC. This DTC may have been inadvertently set at the factory and it has no functional effect on the vehicle. The DTC will permanently clear after 96 key cycles when the vehicle is driven over 20 km/h (13 mph), and no further action or repair is necessary.

LAND ROVER · 2018-09-18

Customer may see message on the Instrument cluster stating "Air suspension not in customer mode" Technician finds diagnostic trouble code (DTC) U3000-05 logged in the Chassis Control Module (CHCM) Vehicle suspension is in tight tolerance mode

LAND ROVER · 2018-09-12

?SOS Limited Availability? warning is displayed on the IC (Instrument Cluster along with Diagnostic Trouble Code (DTC) U3000-49 logged in the TCU (Telematics Control Unit).

JAGUAR · 2018-09-12

?SOS Limited Availability? warning is displayed on the IC (Instrument Cluster along with Diagnostic Trouble Code (DTC) U3000-49 logged in the TCU (Telematics Control Unit).

JAGUAR · 2018-08-29

Issue: ?SOS Limited Availability? warning is displayed on the IC (Instrument Cluster along with Diagnostic Trouble Code (DTC) U3000-49 logged in the TCU (Telematics Control Unit).

LAND ROVER · 2018-08-28

"SOS Limited Availability" warning is displayed on IC (Instrument Cluster along with Diagnostic Trouble Code (DTC) U3000-49 logged in the TCU (telematics Control Unit)).

FORD · 2018-07-27

Some 2018 Escape vehicles equipped with BLIS and CTA built on or before 4-May-2018 may exhibit BLIS and CTA fault messages in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U3000:46 stored in the side obstacle detection control module left side (SODL) or side obstacle detection control module right side (SODR). Follow the Service Procedure steps to correct the condition.

MAZDA · 2018-07-06

Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTC is stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. The combination of warning lights mentioned by the customer may include: SCBS/SBS LAS/LDWS HBC Master Warning Light Instrument Cluster Multi-Information Display (if equipped) warning messages may include: Forward Smart City Brake Support Malfunction. Smart Brake System Malfunction. Front Camera Sensor System Malfunction. MAZDA CONNECT center display warning messages may include: High Beam Control [HBC] / Lane-keep Assist System [LAS] Malfunction. Have the vehicle checked by a dealer if this indicator stays on. Smart City Brake Support [SCBS]…