P0088 · Comunicaciones del fabricante

VOLKSWAGEN · 2022-09-22

DTC's P053F,P0087, P0088, P1025 may set due to the high pressure fuel pump being out of time (sync).

AUDI · 2022-08-23

This bulletin advises to perform the test G265 that if GFF via ODIS yields no results for DTCs P019100, P008700, and P008800.

RAM · 2022-08-06

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P2183 - Engine Coolant Temperature Sensor 2 Circuit Performance. P258B - Electric Vacuum Pump Performance. P040F - EGR Temperature Sensor A-B Correlation. P2D2F - Turbocharger-Supercharger -A- Underboost Condition. P0088 - Fuel Rail Pressure Too High. P026D - Fuel Injection Quantity Higher Than Expected. P208B - Reductant Pump 1 Control Performance. P20C6 - Reductant Heater 4 Control Circuit Performance. P016F - Closed Loop Fuel Pressure Control At Limit - Pressure…

RAM · 2022-05-24

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module (ECM) / Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0506-00-Idle Control System RPM - Lower Than Expected. P0088 - Fuel Rail Pressure Too High - Bank 1. P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P0305-00 - Cylinder 5 Misfire. P0306-00 - Cylinder 6 Misfire. P1C54-00 - SCR NOx Catalyst Missing.…

VOLKSWAGEN · 2022-05-19

Diagnostic aid for DTC P0088 & P1025.

RAM · 2022-03-18

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module (ECM) / PowertrainControl Module (PCM) with the latest available software. Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following Diagnostic Trouble Codes (DTCs) have been set: P0506-00-Idle Control System Rpm - Lower Than Expected. P0088 - Fuel Rail Pressure Too High - Bank 1(Sym Cam Only) P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire(Sym Cam Pump Only). P0302-00 - Cylinder 2 Misfire(Sym Cam Pump Only). P0303-00 - Cylinder 3 Misfire(Sym Cam Pump Only). P0304-00 - Cylinder 4 Misfire(Sym Cam Pump Only). P0305-00 - Cylinder 5 Misfire(Sym Cam Pump…

RAM · 2022-03-18

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module (ECM) / PowertrainControl Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following Diagnostic Trouble Codes (DTCs) have been set: P0506-00-Idle Control System Rpm - Lower Than Expected. P0088 - Fuel Rail Pressure Too High - Bank 1(Sym Cam Only) P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire(Sym Cam Pump Only). P0302-00 - Cylinder 2 Misfire(Sym Cam Pump Only). P0303-00 - Cylinder 3 Misfire(Sym Cam Pump Only). P0304-00 - Cylinder 4 Misfire(Sym Cam Pump Only). P0305-00 -…

RAM · 2022-03-18

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module (ECM) / PowertrainControl Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following Diagnostic Trouble Codes (DTCs) have been set: P0506-00-Idle Control System Rpm - Lower Than Expected. P0088 - Fuel Rail Pressure Too High - Bank 1(Sym Cam Only) P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire(Sym Cam Pump Only). P0302-00 - Cylinder 2 Misfire(Sym Cam Pump Only). P0303-00 - Cylinder 3 Misfire(Sym Cam Pump Only). P0304-00 - Cylinder 4 Misfire(Sym Cam Pump Only). P0305-00 -…

JEEP · 2022-01-05

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following DTCs have been set: P04DB - Crankcase Ventilation System Disconnected. P040F - EGR Temperature Sensor A-B Correlation. P225D - Nox Sensor 1/1 Performance - Signal Stuck Low. P0088 - Fuel Rail Pressure Too High. P0404 - EGR ?A? Control Circuit Range/Performance. P20C6 - Reductant Heater 4 Control Circuit Performance. P208B - Reductant Pump 1 Control Performance. P0524 - Low oil pressure (during start up in cold ambient temps). P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control. P02E8-00 -…

FORD · 2020-11-04

Certain 2020 Model Year Super Duty and 2021 Model Year Medium Duty Vehicles Equipped with a 6.7L Engine Left Hand Side High Pressure Fuel Rail Replacement. In some of the affected vehicles, the vehicle may have been built with a high pressure fuel rail where the internal fuel orifice may become dislodged. If the fuel orifice becomes dislodged, it can travel down and damage the pressure control valve pintle resulting in a Diagnostic Trouble Code (DTC) P0088. Before demonstrating or delivering any new in-stock vehicles involved in this program, dealers are to replace the left hand side high pressure fuel rail using the technical instructions, even if DTC P0088 is not present. This service must be performed on all affected vehicles at no charge to the vehicle owner.

FORD · 2020-09-17

Some 2020 F-Super Duty and 2021 F-650/F-750 vehicles equipped with a 6.7L diesel engine built on 01-Mar-2020 and through 31-Aug-2020 may exhibit an illuminated malfunction indicator light (MIL) with diagnostic trouble code (DTC) P0088. This may be due to the pressure control valve in the left fuel rail. To correct the condition, replace the left fuel rail along with the pressure control valve (PCV). For F-250 through F-550 vehicles refer to Workshop Manual (WSM), Section 303-04B. For F-650/F-750 vehicles refer to WSM, Section 303-04A. For claiming use causal part 9D280 and applicable labor operations in Section 09 of the Service Labor Time Standards (SLTS) Manual.

CHEVROLET, GMC · 2018-07-30

This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. After the fuel system is cleaned out test the fuel using the latest version of PIT3173.

CHEVROLET, GMC · 2018-06-18

This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. After the fuel system is cleaned out test the fuel using the latest version of PIT3173.

CHEVROLET, GMC · 2017-09-18

This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. After the fuel system is cleaned out test the fuel using the latest version of PIT3173.

CHEVROLET, GMC · 2017-08-02

This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. After the fuel system is cleaned out test the fuel using the latest version of PIT3173.

VOLKSWAGEN · 2016-09-23

ENHANCED DIAGNOSTIC ASSISTANCE FOR DTCS P0088 AND P1025

CHEVROLET, GMC · 2016-05-02

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT AND REPLACE NECESSARY FUEL COMPONENTS TO CORRECT A CUSTOMER CONCERN OF HARD START OR A NO START AND DTCS P0087, P0088, P0191 OR P128E SET CAUSED BY THE FUEL SYSTEM BEING CONTAMINATED WITH DEBRIS.

VOLKSWAGEN · 2016-02-15

MIL on, No start, Running rough with DTCs P0087,P0088 or P0191 stored in ECM Fault memory.

CHRYSLER · 2015-09-12

Fuel Control Actuator if a vehicle arrives with an active MIL on for DTC P0088 - Fuel Rail Pressure Too High Bank 1, please do not replace any parts at this time. This DTC is currently being investigated to determine the root cause. Cummins Engineering would like to visit a dealership to acquire information from that vehicle. Please contact Christine Donegan at STAR at (866) 799-1692 ext 1257.~ If you do not receive an answer or call back within 15 minutes, proceed with normal diagnostics

HONDA · 2015-06-11

"DEALER MESSAGE - THIS IS TO INFORM YOUTHAT HONDA SERVICE BULLETIN 15-036, MILCOMES ON WITH DTC P0088 FAILED TO POST IN THE SERVICE INFORMATION SYSTEM ON 06/11/2015. YOUCAN FIND THIS BULLETIN ONLYIN W HAT’S HOT IN THE SERVICE INFORMATION SYSTEM. THIS BULLETIN SHOULD BE AVAILABLE IN THE SERVICE INFORMATION SYSTEM IN W HAT’S NEW AND SEARCHBYVEHICLE ON 06/12/2015."

CHEVROLET, GMC · 2015-06-08

This Preliminary Information communication provides information to the technician about vehicles that have a hard start or a no start. Technician may find Diagnostic Trouble Code DTCs P0087, P0088, P0191 or P128E. Technician will need to follow all Service Information diagnose for the Diagnostic Trouble Code. If the current Service Information diagnostic has led to Fuel Injection Pump replacement, Fuel Pressure Regulator 1 must be inspected for magnetic metal debris. If there is a questionable amount of magnetic debris found on Pressure Regulator 1 remove the Fuel Rail Pressure Sensor and/or Fuel Pressure Regulator 2 to inspect for magnetic metal debris. If technician will need to replace all of the parts listed under the latest version of PIP4949 found in the Service Forms section of…

MAZDA · 2015-04-08

SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0191:00 OR DTC P0088:00 STORED IN MEMORY. DTC P0191:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (EXCEPT 2014 MAZDA3) DTC P0088:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (2014 MAZDA3) THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.

CHEVROLET, FOREST RIVER, GMC · 2014-08-07

This Preliminary Information communication provides information to the technician about vehicles that have a hard start or a no start. Technician may find Diagnostic Trouble Code DTCs P0087, P0088, P0191 or P128E. Technician will need to follow all Service Information diagnose for the Diagnostic Trouble Code. If the current Service Information diagnostic has led to Fuel Injection Pump replacement, Fuel Pressure Regulator 1 must be inspected for magnetic metal debris. If there is a questionable amount of magnetic debris found on Pressure Regulator 1 remove the Fuel Rail Pressure Sensor and/or Fuel Pressure Regulator 2 to inspect for magnetic metal debris. If technician will need to replace all of the parts listed under the latest version of PIP4949 found in the Service Forms section of…

JEEP · 2014-07-11

Flash: MIL Illumination - Remote Start, Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Remote Start will not start the vehicle in cold 14° F (-10° C) ambient temperatures. Software enhancements will help this issue. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ?…

CHEVROLET, GMC · 2014-06-26

This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. After the fuel system is cleaned out test the fuel using the latest version of PIT3173.

JEEP · 2014-04-16

Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 -…

JEEP · 2014-04-16

Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 -…

JEEP · 2014-03-21

Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set: ? P0073 - AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH ? P0088 - FUEL RAIL PRESSURE TOO HIGH ? P016F - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P0420 - CATALYST EFFICIENCY (BANK 1) ? P0426 - CATALYST TEMPERATURE SENSOR CIRCUIT…

VOLKSWAGEN · 2014-03-20

MIL ON, No Start, or Rough Running with DTCs P0087, P0088 or P0191 Stored in ECM Fault Memory (TDI ONLY)

JEEP · 2014-03-18

Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set: ? P0073 - AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH ? P0088 - FUEL RAIL PRESSURE TOO HIGH ? P016F - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P0420 - CATALYST EFFICIENCY (BANK 1) ? P0426 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B - INTERNAL…