P00C6 · Comunicaciones del fabricante

JEEP · 2024-08-08

"Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● **P00F3-00 - Humidity Sensor Circuit Range-performance.** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. ● P0461-00 - Fuel Level Sensor ""A"" Circuit Range/Performance. ● P051B-00 - Crankcase Pressure Sensor Circuit Range/Performance. ● P2F64-00 - Ion Sense Feedback Circuit A. ● P0331-00 - Knock Sensor 2 Circuit Range/Performance. ● P0300-00 - Multiple Cylinder Misfire. ● P2C90-00 - Crankcase Ventilation System - Hose ""A"" Disconnected. ● P0011-00 - Bank 1…

JEEP · 2024-06-15

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. ● P0300-00 - Multiple Cylinder Misfire. Customers may also comment on one or more of the following: ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezing temperatures. This bulletin involves reprogramming the PCM with the latest available software."

JEEP · 2024-06-15

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. ● P0300-00 - Multiple Cylinder Misfire. Customers may also comment on one or more of the following: ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezing temperatures. This bulletin involves reprogramming the PCM with the latest available software."

FORD, LINCOLN · 2024-04-25

Some 2018-2019 Explorer and 2018-2024 Transit/F-150/Expedition/Navigator vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking for an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Confirm FPCM connector (Explorer - C3239, Transit - C433, F-150 - C460/C4336, Expedition/Navigator - C433/C4033) is fully seated and inspect applicable grounds (Explorer G302, Transit - G401, F-150 - G401, Expedition/Navigator - G403/G406) prior to performing guided diagnostics or replacing any components.

FORD, LINCOLN · 2024-04-25

Some 2020-2024 Explorer/Aviator vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking the fuel pump monitor (VE518) and/or a fuel pump control (VE225) circuits, connector pin push-outs, damaged pins/terminals, and/or loose/corroded grounds. Inspect FPCM connector C433/C4033, ground G407, and inline connections C1147 and C3136 for being fully seated and damage free prior to performing guided diagnostics or replacing any components.

JEEP · 2024-01-17

Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? **P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. ? P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. ? P0461-00 - Fuel Level Sensor "A" Circuit Range/Performance. ? P051B-00 - Crankcase Pressure Sensor Circuit Range/Performance. ? P2F64-00 - Ion Sense Feedback Circuit A. ? P0331-00 - Knock Sensor 2 Circuit Range/Performance. ? P0300-00 - Multiple Cylinder Misfire.** ? P2C90-00 - Crankcase Ventilation System - Hose "A" Disconnected. ? P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or System Performance.…

JEEP · 2024-01-17

Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? **P00C6 - Fuel Rail Pressure Too Low - Engine Cranking Bank 1. ? P06DD - Engine Oil Pressure Control Circuit Performance/Stuck Off. ? P0461 - Fuel Level Sensor "A" Circuit Range/Performance.** ? P2C90-00 - Crankcase Ventilation System - Hose "A" Disconnected. ? P0604-00 - Internal Control Module Random Access Memory Ram Error. ? P060C-00 - Internal Control Module Main Processor Performance. This bulletin involves reprogramming the PCM with the latest available software.

JEEP · 2024-01-17

Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? **P00C6 - Fuel Rail Pressure Too Low - Engine Cranking Bank 1. ? P06DD - Engine Oil Pressure Control Circuit Performance/Stuck Off.** ? P0604-00 - Internal Control Module Random Access Memory Ram Error. ? P060C-00 - Internal Control Module Main Processor Performance. This bulletin involves reprogramming the PCM with the latest available software.

FORD · 2023-04-04

Some 2021-2023 Bronco Sport vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P025A, P025B, P00C6, P008A, P0627 and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness, connector pin push-outs or loose/corroded grounds to the fuel pump control module (FPCM) connector, PCM connector and/or battery junction box connector. Inspect the following connectors for 1.5L and 2.0L engines: C1551B, C1035A, C110, C401, C4033, C4330. Verify the connections are fully seated, without damage and/or pushed out pins/terminals prior to performing Workshop Manual (WSM) diagnostics or replacing any components. Inspect G404 and verify it's clean and secure. If any connector damage is found, repair as…

FORD, LINCOLN · 2023-01-19

Some 2018-2023 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing…

FORD, LINCOLN · 2022-06-08

Some 2018-2022 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing…

FORD · 2022-06-03

Some 2022 Maverick vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P025A, P025B, P00C6, P008A, P0627 and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness, connector pin push-outs or loose/corroded grounds to the fuel pump control module (FPCM) connector, PCM connector and/or battery junction box connector. Inspect the following connectors: C1381B (2.5L hybrid) or C1551B (2.0L engine), C1035A, C4033, C219, and C405. Verify the connections are fully seated, without damage and/or pushed out pins/terminals prior to performing Workshop Manual (WSM) diagnostics or replacing any components. Inspect G406 and verify it's clean and secure. If any connector damage is found, repair as…

MACK, VOLVO · 2022-05-25

Common Rail Fuel System - Diagnostic Trouble Codes (DTC) P0094, P228F, P016F, P0087,P00C6, P0257, P2A17, P2A1F, P008A - US17+OBD* Emissions, Model Years 2018 To 2020

VOLVO · 2022-05-25

Common Rail Fuel System - Diagnostic Trouble Codes (DTC) P0094, P228F, P016F, P0087,P00C6, P0257, P2A17, P2A1F, P008A - US17+OBD* Emissions, Model Years 2018 To 2020

FORD, LINCOLN · 2022-04-06

Some 2018-2022 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with Diagnostic Trouble Codes (DTCs) P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2022 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

CADILLAC, CHEVROLET, GMC · 2020-01-10

This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.

VOLVO · 2019-12-16

Common Rail Fuel System Faults - Diagnostic Trouble Codes (DTC) P0094, P228F, P016F, P0087,P00C6, P0257, P2A17, P2A1F, P008A; Repair Information - US17+OBD16, US17+OBD18, and US17+OBD19 Emissions, Model Years 2018 To 2020

MACK · 2019-12-16

Common Rail Fuel System Faults - Diagnostic Trouble Codes (DTC) P0094, P228F, P016F, P0087,P00C6, P0257, P2A17, P2A1F, P008A; Repair Information - US17+OBD16, US17+OBD18, and US17+OBD19 Emissions, Model Years 2018 To 2020

FORD, LINCOLN · 2019-12-11

Some 2013-2015 Fusion/MKZ/Escape/MKC with a 1.6L GTDI, 1.5L GTDI, or 2.0L GTDI may exhibit a lack of power, loss of power, or stall when placed in gear with DTCs P00C6, P0087, P008A, P008B, P018C, or P018D. If normal diagnosis leads to a biased or failed Fuel Low Pressure (FLP) sensor, the sensor is available without the need to order the entire fuel line assembly. The FLP sensor, located on the fuel supply line to the high pressure pump, provides the low side fuel pressure input to the PCM so the Fuel Driver Module can be controlled accordingly. The FLP PID can be viewed in the Datalogger and then compared to a manual pressure gauge per pinpoint test HC in the PCED to validate the sensor is working properly. The Fusion/MKZ catalog has been updated to show the sensor availability.

VOLVO · 2019-10-22

Common Rail Fuel System Faults - Diagnostic Trouble Codes (DTC) P0094, P228F, P016F, P0087,P00C6, P0257, P2A17, P2A1F; Repair Information - US17+OBD16, US17+OBD18, and US17+OBD19 Emissions, Model Years 2018 To 2020

NISSAN · 2019-01-25

2016-2019 TITAN XD DIESEL; FUEL FILTER MAINTENANCE This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 diesel engine. SERVICE INFORMATION The Stage 1 and Stage 2 fuel filters must be replaced every 10,000 miles or a restriction may develop. DTCs P008A, P00C6, P0087 and/or a whining noise from the Stage 1 Fuel Filter Module may be present due to a restriction in the Stage 1 and/or Stage 2 fuel filters. NOTE: An inoperable or whining Stage 1 Fuel Filter Module that has not had the fuel filters regularly replaced as per the Owner?s Manual Maintenance schedule is not a warrantable repair. Before proceeding with any fuel system restriction diagnosis: - Confirm that both of the vehicle?s Stage 1 and Stage 2 fuel filters have been replaced at the correct service intervals, as…

CADILLAC, CHEVROLET, GMC · 2018-01-12

This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.

CADILLAC, CHEVROLET, GMC · 2016-11-23

This engineering information bulletin is ending the need for information on vehicles with the condition of Vehicle Crank with No Start or Stalling with DTC P0011 and/or P00C6 Set.

CADILLAC, CHEVROLET · 2016-10-21

16029 - Service Update. The high pressure fuel pump or fuel rail fastener(s) may have been improperly tightened during manufacturing. Fuel could leak from the fuel pump or fuel rail causing the vehicle to go into reduced power mode. If this occurs DTC P228C, P228D or P00C6 will set, causing the Check Engine Light to be illuminated.

CADILLAC, CHEVROLET, GMC · 2016-03-09

This engineering informational bulletin is requesting information from th field on vehicles that have the condition of a vehicle crank and no start with DTC P0011 and or P00C6 set

CADILLAC, CHEVROLET, GMC · 2016-03-04

This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.

CADILLAC, CHEVROLET, GMC · 2016-02-15

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN HOW TO DIAGNOSE AND REPAIR A VEHICLE WITH AN ENGINE THAT RUNS WITH AN INTERMITTENT CRANK NO START WITH A DIAGNOSTIC TROUBLE CODE P0011 OR P00C6 CURRENT OR HISTORY. THE CAMSHAFT POSITION ACTUATOR SOLENOID VALVE MAY BE STICKING OR BINDING CAUSING THE VALVE TIMING TO BE RETARDED. DEALER WILL NEED TO CYCLE THE CAMSHAFT POSITION ACTUATOR SOLENOID VALVE BY ENERGIZING IT USING GLOBAL DIAGNOSTIC SYSTEM 2.

CHEVROLET, GMC · 2015-06-01

This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.

BUICK, CADILLAC, CHEVROLET, GMC · 2015-05-14

This Preliminary Information communication advises the technician to follow this Preliminary Information if there is a diagnostic trouble code P00C6 and or P228C set and normal Service Information diagnostics didn?t lead to a repair. Technician is to recheck the terminals at the Engine Control module for fit and tension as well as the crimp to the wire. The engine control module terminals to inspect are in the X2 connector. Inspect terminal number 3, 18 and 19 for the fuel rail pressure sensor and in the X3 connector terminals 16 and 32 for the high pressure fuel pump. The diagnostic trouble codes could set with as little as a 2 ohm resistance reading on these circuits. If any concerns are found replace the affected terminals and verify the repair.

LAND ROVER · 2015-04-08

"SITUATION: THE ENGINE MALFUNCTION INDICATOR LAMP (MIL) MAY BE ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTC) P00C6 AND P228D-00 OR P228C-77 STORED IN THE ENGINE CONTROL MODULE (ECM). ADDITIONALLY, THE ENGINE MAY EXPERIENCE ROUGH RUNNING, HARD STARTING, A ROUGH IDLE, OR MISFIRES AND ONE OR MORE MISFIRE DTCS (P0300, P0301, P0302, P0303, P0304, AND P1315) STORED IN THE ECM. CAUSE: THIS MAY BE CAUSED BY AN INTERNAL FAULT WITH THE METERING VALVE IN THE HIGH PRESSURE FUEL PUMP"