U3000 · Comunicaciones del fabricante

JAGUAR · 2018-06-27

An issue has been identified on a limited number of Jaguar vehicles within the listed Affected Vehicle Range may display an Adaptive Damping (AD) warning message on the Instrument Cluster. Investigations have identified that on occasion, the Diagnostic Trouble Code (DTC) U3000-04 may be stored in the Chassis Control Module (CHCM), which will lead to the warning message being displayed. The warning message will remain present until the ignition has been cycled OFF and ON; however, the warning message will be displayed again until the software update below is performed.

JAGUAR · 2018-06-27

An issue has been identified on certain Jaguar vehicles within the listed Affected Vehicle Range may display an Adaptive Damping (AD) warning message on the Instrument Cluster. Investigations have identified that on occasion, the Diagnostic Trouble Code (DTC) U3000-04 may be stored in the Chassis Control Module (CHCM), which will lead to the warning message being displayed. The warning message will remain present until the ignition has been cycled OFF and ON; however, the warning message will be displayed again until the software update below is performed.

FORD, LINCOLN · 2018-04-13

Some 2016 Edge/MKX vehicles may exhibit an illuminated adaptive/active steering fault message in the instrument panel cluster (IPC) message center with diagnostic trouble codes (DTCs) U3000, C2003, B137F, B1380, U210A, and U2000 stored in the SECM. If these DTCs are present, replace the SECM. Use causal part 3600 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.

CADILLAC · 2018-04-04

This technical bulletin provides a procedure to reprogram both the active safety control module and the IPC to correct a condition of Super Cruise Function Difficult to Engage, Inadequate Messaging, or Service Driver Assist Message Displayed with DTC U3000.49 due to a calibration concern.

LAND ROVER · 2018-03-15

An issue has been identified on certain vehicles within the listed Affected Vehicle Range which may display an Adaptive Damping (AD) warning message on the Instrument Cluster (IC). Investigations have identified that Diagnostic Trouble Code (DTC) U3000-04 may be stored in the Chassis Control Module (CHCM), leading to the warning message being displayed within the IC. The warning message will remain present until the ignition has been cycled 'OFF' and then 'ON' but will be displayed again until the update listed within the Diagnostic Procedure below is completed.

MAZDA · 2017-12-22

Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTCs are stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. U3000:04 - Forward sensing camera (FSC) internal malfunction. The combination of warning lights mentioned by the customer may include: SCBS/SBS, LAS/LDWS, HBC, Master Warning LightInstrument Cluster Multi-Information Display (if equipped) warning messages may include: Forward Smart City Brake Support Malfunction, Smart Brake System Malfunction, Front Camera Sensor System Malfunction, MAZDA CONNECT center display warning messages may include: High Beam Control [HBC] / Lane-keep Assist System [LAS] Malfunction. Have the vehicle checked by a dealer…

LAND ROVER · 2017-12-15

A potential issue has been identified on a limited number of Land Rover vehicles within the listed Affected Vehicle Range which may display an Adaptive Damping (AD) warning message on the Instrument Cluster (IC). Investigations have identified that Diagnostic Trouble Code (DTC) U3000-04 may be stored in the Chassis Control Module (CHCM), leading to the warning message being displayed within the IC. The warning message will remain present until the ignition has been cycled 'OFF' and then 'ON' but will be displayed again until the update listed within the Diagnostic Procedure of the Technical Bulletin below is completed.

LAND ROVER · 2017-12-15

An issue has been identified on certain vehicles within the listed Affected Vehicle Range which may display an Adaptive Damping (AD) warning message on the Instrument Cluster (IC). Investigations have identified that Diagnostic Trouble Code (DTC) U3000-04 may be stored in the Chassis Control Module (CHCM), leading to the warning message being displayed within the IC. The warning message will remain present until the ignition has been cycled 'OFF' and then 'ON' but will be displayed again until the update listed within the Diagnostic Procedure below is completed.

FORD, LINCOLN · 2017-11-03

Some 2017-2018 Fusion/MKZ vehicles built on or before 27-Oct-2017 may exhibit an illuminated airbag lamp and/or SYNC 911 assist not operational message being displayed. Connect the IDS and check the RCM and APIM for DTCs. If any of the following RCM DTCs U3000, U2100, U2101, U2300, U0455, B0080, B141B, B141C, B0054, B140C, B140D, B0057, B140E, B140F and/or APIM DTC U0452 is stored, then reprogram the RCM to the latest level using IDS or FJDS 107.04 or higher. After reprograming, perform an as-built configuration of the RCM. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 14B321 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual. Calibration files may also…

MAZDA · 2017-10-06

Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTCs are stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. U3000:04 - Forward sensing camera (FSC) internal malfunction. The combination of warning lights mentioned by the customer may include: Instrument Cluster Multi-Information Display (if equipped) warning messages may include: Forward Smart City Brake Support Malfunction, Smart Brake System Malfunction, Front Camera Sensor System Malfunction, MAZDA CONNECT center display warning messages may include: High Beam Control [HBC] / Lane-keep Assist System [LAS] Malfunction. Have the vehicle checked by a dealer if this indicator stays on. Smart City Brake…

LAND ROVER · 2017-09-25

Issue: A customer may report that one or both of the messages "Suspension fault, Drive with care." or "Adaptive dynamics fault" are displayed intermittently on the Instrument Cluster. Following diagnosis using Pathfinder the Diagnostic Trouble Code (DTC) U3000-04 ?Control Module System Internal Failure? is stored in the Chassis Control Module (CHCM). Concern applicable to 2017 MY vehicles only.

LAND ROVER · 2017-09-11

Issue: At PDI or at normal service, the dealer may find DTC - U3000 - 49 Control Module internal electronic failure * recorded in the Side Object Detection Left (SODL) or Side Object Detection Right(SODR) without any customer impact on the Blind Spot Monitor features.

JAGUAR · 2017-09-08

Issue: At PDI or at normal service, the dealer may find DTC - U3000 - 49 Control Module internal electronic failure ? recorded in the Side Object Detection Left (SODL) or Side Object Detection Right(SODR) without any customer impact on the Blind Spot Monitor features.

MAZDA · 2017-09-01

Some vehicles with Blind Spot Monitoring (BSM) may experience the following conditions (similar to when the BSM control modules detect dirt on the rear bumper surface): DTC U1A4B:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (RH)), DTC U3000:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (LH)), The BSM turns ?OFF? and the BSM OFF indicator turns ?ON? in the instrument cluster while driving, The BSM will not turn on again during the drive cycle, After cycling the ignition switch off and on again, the BSM operates normally, DTC U1A4B:97 or U3000:97 is stored in memory. To correct…

TOYOTA · 2017-08-14

TSB: Some 2017 model year iA vehicles may exhibit Diagnostic Trouble Codes (DTCs) U0323 (PCM Software Incompatibility with Instrument Panel Control Module), U0423 (ABS Invalid Data Received from Instrument Panel Cluster Control Module), or U3000 (IC Control Module Internal Electronic Failure) if the vehicle?s battery or the multimedia display is disconnected. Follow the Repair Procedure in this bulletin to address this condition.

SCION · 2017-08-14

TSB: Some 2016 model year iA vehicles may exhibit Diagnostic Trouble Codes (DTCs) U0323 (PCM Software Incompatibility with Instrument Panel Control Module), U0423 (ABS Invalid Data Received from Instrument Panel Cluster Control Module), or U3000 (IC Control Module Internal Electronic Failure) if the vehicle?s battery or the multimedia display is disconnected. Follow the Repair Procedure in this bulletin to address this condition.

LAND ROVER · 2017-06-23

Issue: A customer may report that the air suspension warning message is displayed intermittently on the Instrument Cluster. Following diagnosis using Pathfinder the diagnostic trouble Code (DTC) U3000-04 ?Control module System Internal Failure? is stored in the Chassis Control Module (CHCM)

LAND ROVER · 2017-06-23

Issue: A customer may report that the air suspension warning message is displayed intermittently on the Instrument Cluster. Following diagnosis using Pathfinder the diagnostic trouble Code (DTC) U3000-04 ?Control module System Internal Failure? is stored in the Chassis Control Module (CHCM).

MAZDA · 2016-11-03

Mulri-Model (Equipped with Mazda connect) - DTC U0323/U0423/U3000 Cannot be deleted (Update)

FORD, LINCOLN · 2016-11-02

SOME 2016 EDGE/MKX VEHICLES MAY EXHIBIT AN ILLUMINATED ADAPTIVE/ACTIVE STEERING FAULT MESSAGE IN THE INSTRUMENT PANEL CLUSTER (IPC) MESSAGE CENTER WITH DIAGNOSTIC TROUBLE CODES (DTCS) U3000, C2003, B137F, B1380, U210A, AND U2000 STORED IN THE SECM. IF DTC U3000:96 IS PRESENT, THE SECM MUST BE REPLACED. IF DTC U3000:96 IS NOT PRESENT, REPROGRAM THE SECM TO THE LATEST CALIBRATION USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) RELEASE 102.05 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL PART 3600 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

FORD, LINCOLN · 2016-10-05

SOME 2017 FUSION/MKZ VEHICLES BUILT ON OR BEFORE 18-AUG-2016 MAY EXHIBIT AN AIR BAG LAMP. CONNECT THE IDS AND CHECK THE RCM FOR DTCS. IF DTC U3000, U2100, U2101, U2300, U0455, U0452, B0080, B141B, B141C, B0054, B140C, B140D, B0057, B140E, AND/OR B140F ARE STORED IN THE RCM, REPROGRAM THE RCM TO THE LATEST LEVEL USING IDS RELEASE 102.03 OR HIGHER. AFTER REPROGRAMING, PERFORM AN AS-BUILT CONFIGURATION OF THE RCM. SELECT NO WHEN ASKED IF YOU WERE SENT HERE BY AN ARTICLE. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. USE THE APPLICABLE LABOR OPERATION IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS MANUAL AND CAUSAL PART 14B321 WHEN CLAIMING THIS REPAIR. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM

FORD, LINCOLN · 2016-09-02

Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may have DTCs U3000:04, B108E:12 and/or U1A00:87 present in the APIM. If these DTCs are present and no other symptoms are reported by the customer, then clear the DTCs and retest. If the DTC(s) do not return then no further repairs should be attempted. If one or more DTCs return as current faults and/or the customer reports other symptoms, then refer to Workshop Manual, Section 415-00 for further diagnostics. The SYNC version can be confirmed via OASIS.

FORD · 2016-08-17

SOME 2015-2016 F-150 VEHICLES EQUIPPED WITH ADAPTIVE CRUISE CONTROL MAY EXHIBIT A COLLISION WARNING MALFUNCTION AND/OR ADAPTIVE CRUISE MALFUNCTION MESSAGE IN THE INSTRUMENT CLUSTER MESSAGE CENTER WITH DIAGNOSTIC TROUBLE CODES (DTC) B142E:78 AND/OR U3000:49 IN THE CRUISE CONTROL MODULE (CCM). TO CORRECT THIS CONDITION, UPDATE THE CCM TO THE LATEST CALIBRATION LEVEL USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) VERSION 101.03 OR HIGHER. REFER TO WORKSHOP MANUAL (WSM) SECTION 419-03B TO PERFORM THE CRUISE CONTROL RADAR ALIGNMENT PROCEDURE. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL PART 9E731 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE…

HONDA · 2016-07-12

TECHLINE SUMMARY ARTICLE - WE’RE GETTING REPORTS OF THE BRAKE INDICATOR BLINKING AFTER TURNING THE IGNITION TO OFF AND APPLYING THE ELECTRIC PARKING BRAKE. THERE MAY ALSO BE A DTC U3000-49 (ECU INTERNAL CIRCUIT MALFUNCTION) BEING SET. WHEN THE BRAKE INDICATOR BLINKS, IT MEANS THERE’S A PROBLEM WITH THE ELECTRIC PARKING BRAKE SYSTEM AND THE PARKING BRAKE MAY HAVE NOT PROPERLY APPLIED.

FORD, LINCOLN · 2016-05-09

SYNC 3 ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DTCS U3000 OR B108E OR U1A00

LAND ROVER · 2016-04-25

SITUATION: ON VEHICLES FITTED WITH ACTIVE DRIVELINE, THE MESSAGE 'TWO WHEEL DRIVE ONLY FAULT - TRACTION REDUCED' MAY BE DISPLAYED ON THE INSTRUMENT CLUSTER. DIAGNOSTIC TROUBLE CODES (DTC) P0745-92, P0942-92, P0C06-00, P18A5-64, U0001-82, U0001-83, U0001-87, U0037-81, U0037-82, U0037-83, U0037-87, AND U3000-49 MAY BE STORED IN THE ALL WHEEL DRIVE CONTROL MODULE (AWDCM)

MAZDA · 2016-01-01

MULTI-MODEL (EQUIPPED WITH MAZDA CONNECT). SOME VEHICLES (WITH MAZDA CONNECT) MAY EXHIBIT A CONDITION WHERE DTC U0323 (PCM)/U0423(ABS)/U3000(IC) CANNOT BE DELETED WHEN THE TPMS WARNING LIGHT FLASHES AND/OR THE TCS/DSC INDICATOR LIGHTS ARE ILLUMINATED. THIS CAN HAPPEN IF THE IGNITION IS TURNED OFF WITH 20 SECONDS AFTER THE IGNITION IS TURNED ON IN ONE OF THE FOLLOWING TWO SITUATIONS. 1. THE "ROOM" FUSE (ENGINE COMPARTMENT) IS NOT INSTALLED WHEN BATTERY LEVEL IS LOW. 2. THE CMU (CONNECTIVITY MASTER UNIT) IS NOT CONNECTED.

MAZDA · 2015-12-10

BSM off indicator on with DTC U1A4B:97 or U3000:97

MAZDA · 2015-12-10

BSM OFF INDICATOR ON WITH DTC U1A4B:97 OR U3000:97. SOME VEHICLES WITH BLIND SPOT MONITORING (BSM) MAY EXPERIENCE THE FOLLOWING CONDITIONS (SIMILAR TO WHEN THE BSM CONTROL MODULES DETECT DIRT ON REAR BUMPERS SURFACE): BSM TURNS "OFF" AND BSM OFF INDICATOR TURNS "ON" IN THE INSTRUMENT CLUSTER WHILE DRIVING; BSM WILL NOT TURN ON AGAIN DURING DRIVE CYCLE; AFTER CYCLING, IGNITION SWITCH OFF AND ON AGAIN, BSM OPERATES NORMALLY; DTC U1A4B:97 OR U3000:97 IS STORED IN MEMORY.

MAZDA · 2015-12-09

SOME VEHICLES WITH BLIND SPOT MONITORING (BSM) MAY EXPERIENCE THE FOLLOWING CONDITIONS (SIMILAR TO WHEN THE BSM CONTROL MODULES DETECT DIRT ON THE REAR BUMPER SURFACE):• THE BSM TURNS “OFF” AND THE BSM OFF INDICATOR TURNS “ON” IN THE INSTRUMENT CLUSTER WHILE DRIVING • THE BSM WILL NOT TURN ON AGAIN DURING THE DRIVE CYCLE • AFTER CYCLING THE IGNITION SWITCH OFF AND ON AGAIN, THE BSM OPERATES NORMALLY • DTC U1A4B:97 OR U3000:97 IS STORED IN MEMORY - DTC U1A4B:97 - RADAR SENSOR SENSITIVITY TEMPORARILY DECREASES DEPENDING ON VARIOUS EXTERNAL AND ENVIRONMENTAL FACTORS (BLIND SPOT MONITORING (BSM) CONTROL MODULE (RH)) - DTC U3000:97 - RADAR SENSOR SENSITIVITY TEMPORARILY DECREASES DEPENDING ON VARIOUS EXTERNAL AND ENVIRONMENTAL FACTORS (BLIND SPOT MONITORING (BSM) CONTROL MODULE (LH)) TO…