P0138 · निर्माता की तकनीकी जानकारी

JEEP · 2026-04-17

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). ● P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst…

JEEP · 2026-02-17

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P08A6 - Gear Lever Position Sensor System – Multiple Sensor Correlation (Manual Transmission Only). ● P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. ● P0300 - Multiple Cylinder Misfire. ● P152E - Engine Hood Switch 2 Circuit High. ● P0032 - O2 Sensor 1/1 Heater Circuit High. ● P0038 - O2 Sensor 1/2 Heater Circuit High. ● P0052 - O2 Sensor 2/1 Heater Circuit High. ● P0058 - O2 Sensor 2/2 Heater Circuit High. ● P0132 - O2 Sensor 1/1 Circuit High. ● P0138 - O2 Sensor 1/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2…

JEEP · 2026-01-29

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P08A6 – Gear Lever Position Sensor System – Multiple Sensor Correlation (Manual Transmission Only). ● P152F – Engine Hood Switch 2 / Engine Hood Switch 1 Correlation.** ● P0300 - Multiple Cylinder Misfire. ● P152E - Engine Hood Switch 2 Circuit High. ● P0032 - O2 Sensor 1/1 Heater Circuit High. ● P0038 - O2 Sensor 1/2 Heater Circuit High ● P0052 - O2 Sensor 2/1 Heater Circuit High ● P0058 - O2 Sensor 2/2 Heater Circuit High. ● P0132 - O2 Sensor 1/1 Circuit High. ● P0138 - O2 Sensor 1/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High…

SUBARU · 2025-04-22

"This bulletin announces the availability of new oxygen sensors developed to address the following Diagnostic Trouble Codes (DTCs) detected by the Engine Control Module: • P0137: O2 Sensor Circuit Low Voltage Bank 1 Sensor 2 • P0138: O2 Sensor Circuit High Voltage Bank 1 Sensor 2 • P0140: O2 Sensor Circuit No Activity Detected Bank 1 Sensor 2 • P0141: O2 Sensor Heater Circuit Bank 1 Sensor 2"

SUBARU · 2024-05-14

This bulletin announces the availability of new oxygen sensors developed to address the following Diagnostic Trouble Codes (DTCs); P0137 (O2 Sensor Circuit Low Voltage Bank 1 Sensor 2, P0138 (O2 Sensor Circuit High Voltage Bank 1 Sensor 2) P0140 (O2 Sensor Circuit No Activity Detected Bank 1 Sensor 2), and P0141 (O2 Sensor Heater Circuit Bank 1 Sensor 2).

JEEP · 2022-12-01

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon furtherinvestigation the technician may find one or more of the following DTCs: P0300 - Multiple Cylinder Misfire. P152E - Engine Hood Switch 2 Circuit High. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. P0032 - O2 Sensor 1/1 Heater Circuit High. P0038 - O2 Sensor 1/2 Heater Circuit High. P0052 - O2 Sensor 2/1 Heater Circuit High. P0058 - O2 Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High. P2100 - Electronic Throttle Control Motor Circuit. In…

JEEP · 2022-12-01

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: P0300 - Multiple Cylinder Misfire. P0032 - O2-Sensor 1/1 Heater Circuit High. P0038 - O2-Sensor 1/2 Heater Circuit High. P0052 - O2-Sensor 2/1 Heater Circuit High. P0058 - O2-Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High. P2100 - Electronic Throttle Control Motor Circuit. P2107 - Electronic Throttle Control Module Processor.

JEEP · 2022-10-19

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTC: P152E - Engine Hood Switch 2 Circuit High. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. P0032 - O2 Sensor 1/1 Heater Circuit High. P0038 - O2 Sensor 1/2 Heater Circuit High. P0052 - O2 Sensor 2/1 Heater Circuit High. P0058 - O2 Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High. P2100 - Electronic Throttle Control Motor Circuit. P0300 - Multiple Cylinder Misfire. In addition,…

JEEP · 2022-10-11

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following (Diagnostic trouble Codes (DTCs): P0032 - O2-Sensor 1/1 Heater Circuit High. P0038 - O2-Sensor 1/2 Heater Circuit High. P0052 - O2-Sensor 2/1 Heater Circuit High. P0058 - O2-Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High. P2100 - Electronic Throttle Control Motor Circuit. P2107 - Electronic Throttle Control Module Processor.

FORD · 2022-08-23

Some 2021-2022 Bronco Sport vehicles equipped with 2.0L engine may exhibit a malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0036 and/or P0138 stored in the powertrain control module (PCM). This may be due to corrosion or water intrusion in connector C201 and/or C1570. Prior to performing Workshop Manual (WSM) diagnostics, inspect the male and female side of connector C201 and C1570 for signs of corrosion or water intrusion. If corrosion or water intrusion is found, replace connector C201 and/or C1570 with a pigtail kit and apply Motorcraft® Electrical Grease (XG-12) or equivalent.

FORD · 2022-08-03

Some 2022 Maverick vehicles built on or before 4-Apr-2022 equipped with 2.0L engine may exhibit a charging system warning indicator with diagnostic trouble codes (DTCs) U012D, U0284 and/or U042E stored in the powertrain control module (PCM). The vehicle may also exhibit a malfunction indicator lamp (MIL) with DTCs P0036:00 and/or P0138:00 stored in the PCM. This may be caused by water intrusion in the connector C1050. Prior to performing Workshop Manual (WSM) diagnostics, inspect the male and/or female connector C1050 for signs of corrosion or water intrusion. If water or corrosion is found, replace the male and/or female connector C1050 with a pigtail kit and apply electrical grease.

FORD · 2022-07-29

Some 2022 Maverick vehicles built on or before 4-Apr-2022 equipped with 2.0L engine may exhibit a charging system warning indicator with diagnostic trouble codes (DTCs) U012D, U0284 and/or U042E stored in the powertrain control module (PCM). The vehicle may also exhibit a malfunction indicator lamp (MIL) with DTCs P0036:00 and/or P0138:00 stored in the PCM. This may be caused by water intrusion in the connector C1050. Prior to performing Workshop Manual (WSM) diagnostics, inspect the male and/or female connector C1050 for signs of corrosion or water intrusion. If water or corrosion is found, replace the male and/or female connector C1050 with a pigtail kit and apply dielectric grease.

JEEP · 2022-07-15

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following (Diagnostic trouble Codes (DTCs): P0032 - O2-Sensor 1/1 Heater Circuit High. P0038 - O2-Sensor 1/2 Heater Circuit High. P0052 - O2-Sensor 2/1 Heater Circuit High. P0058 - O2-Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High. P2100 - Electronic Throttle Control Motor Circuit.P2107 - Electronic Throttle Control Module Processor.

FORD · 2021-07-19

Some 2020 F-Super Duty vehicles equipped with a 6.2L or 7.3L engine, 10R140 transmission, and built on or before 05-Jun-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0132, P0135, P0138, P0141, P0152, P0155, P0158 and/or P0161 stored in the powertrain control module (PCM). This may be due to water intrusion into heated oxygen sensor (HO2S) connectors C141, C142, C1571 and/or C1572 on the transmission harness where it connects to the engine exhaust sensors. To correct the condition, follow the Service Procedure steps to replace the transmission harness and the affected heated oxygen sensors (HO2S) and/or the catalyst monitor sensor.

FORD · 2020-10-30

Some 2020 F-Super Duty vehicles equipped with the 6.2L or 7.3L engine built on or before 05-Jun-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0132, P0135, P0138, P0141, P0152, P0155, P0158 and/or P0161 stored in the powertrain control module (PCM). This may be due to water intrusion into heated oxygen sensor (HO2S) connectors C141, C142, C1571 and/or C1572 on the transmission harness where it connects to the engine exhaust sensors. To correct the condition, follow the Service Procedure steps to replace the transmission harness and the affected heated oxygen sensors (HO2S) and/or the catalyst monitor sensor.

CHEVROLET, GMC · 2019-11-22

This technical bulletin provides repair information to correct a customer concern of Start/Stop Performance, Hesitation From a Stop, Malfunction Indicator Lamp (MIL) Illuminated - DTC P0132 and/or P0138 Set.

NISSAN · 2019-10-24

2018 ARMADA AND TITAN; MIL ON WITH DTC P0138 AND/OR P0158 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

CHEVROLET, GMC · 2019-04-18

This technical bulletin provides repair information to correct a customer concern of Start/Stop Performance, Hesitation From a Stop, Malfunction Indicator Lamp (MIL) Illuminated - DTC P0132 and/or P0138 Set.

TOYOTA · 2018-12-05

TSB: Some 2009 ? 2012 model year RAV4 and 2010 ? 2011 model year Camry vehicles equipped with 2AR-FE (non-PZEV) engines may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P0138 (Oxygen Sensor Circuit High Voltage [Bank 1 Sensor 2]). This condition may be caused by incorrect air fuel ratio sensor response. The Engine Control Module/ECM (SAE Term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition occurring. Follow the Repair Procedure in this bulletin to address this condition.

NISSAN · 2018-10-19

2018 ARMADA; MIL ON WITH DTC P0138 AND/OR P0158 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NISSAN · 2018-09-11

2018 ARMADA; MIL ON WITH DTC P0138 AND/OR P0158 IF YOU CONFIRM The MIL is ON with one or both of the following DTCs: - P0138 (Heated oxygen sensor heater 2 [bank 1] circuit high voltage) - P0158 (Heated oxygen sensor heater 2 [bank 2] circuit high voltage) And There are no drivability issues. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM.

INFINITI · 2018-09-11

2018 QX80; MIL ON WITH DTC P0138 AND/OR P0158 IF YOU CONFIRM The MIL is ON with one or both of the following DTCs: - P0138 (Heated oxygen sensor heater 2 [bank 1] circuit high voltage) - P0158 (Heated oxygen sensor heater 2 [bank 2] circuit high voltage) And There are no drivability issues. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM.

FORD · 2016-10-13

SOME 2014-2015 EXPLORER AND TAURUS VEHICLES EQUIPPED WITH A 3.5L OR 3.7L TI-VCT ENGINE MAY EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODE (DTC) P0138 AND/OR P0158 STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

NISSAN · 2016-04-11

IF YOU CONFIRM One or more of the following DTCs has set: * P0037 - HO2 HTR (B1) (Heated oxygen sensor 2 heater control circuit low) * P0038 - HO2 HTR (B1) (Heated oxygen sensor 2 heater control circuit high) * P0137 - HO2S2 (B1) (Heated oxygen sensor 2 circuit low voltage) * P0138 - HO2S2 (B1) (Heated oxygen sensor 2 circuit high voltage) * P0139 - HO2S2 (B1) (Heated oxygen sensor 2 circuit slow response) * P2096 - POST CAT FUEL TRIM SYS B1 (Post catalyst fuel trim system too leanbank 1) * P2097 - POST CAT FUEL TRIM SYS B1 (Post catalyst fuel trim system too rich bank 1) ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. If this bulletin applies: 2. Replace the rear O2 sensor. 3. Reprogram the ECM See this bulletin for…

PONTIAC · 2015-11-12

This technical bulletin supplies repair information to correct customer concerns of intermittent MIL/Check Engine light on, DTCs P0607 and/or P0138, vehicle Stability Control lamp on, drivability concerns in high ambient temperatures with A/C on.

LAND ROVER · 2015-10-15

"ISSUE: THE CUSTOMER MAY OBSERVE A MIL IN THE INSTRUMENT CLUSTER RELATING TO THE ENGINE SYSTEM (CHECK ENGINE LIGHT) AND ONE OR MORE CODES STORED IN THE PCM RELATING TO HEATED OXYGEN SENSOR (HO2S) IN THE EXHAUST SYSTEM. THE CODE WILL REFER TO A FAULT WITH THE PRE, OR MID, OR POST CATALYST HEATED OXYGEN SENSOR: P0030, P0031, P00D1, P0130, P0131, P0132, P0133, P0134, P0135, P014C, P2195, P2196, P2231, P2237, P2243, P2245, P2251, P2297, P2626, P2A00, P0050, P0051, P00D3, P0150, P0151, P0152, P0153, P0154, P0155, P2197, P2198, P2234, P2240, P2247, P2254, P0037, P0038, P0054, P0136, P0137, P0138, P0139, P013A, P013E, P0140, P0141, P2270, P2271, P0056, P0057, P0060, P013C, P014A, P0156, P0157, P0158, P0159, P0160, P0161, P2272, P2273, P0042, P0043, P0044, P0055, P0142, P0143, P0144, P0147,…

INFINITI · 2015-06-12

IF YOU CONFIRM: The MIL is ON and any of the following DTCs are stored in the ECM: - P0037, P0038, P0057, P0058, P0139, P0159, P0141, P0161, P0137, P0157, P0138, P0158 ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm if ECM reprogramming applies. 2. If it applies, reprogram the ECM. 3. Replace only the rear O2 sensor that relates to the stored DTC(s) (B1 and/or B2). NOTE: Do NOT replace both rear O2 sensors if the DTC(s) is for one rear O2 sensor. See this bulletin for further detail.

NISSAN · 2015-06-12

IF YOU CONFIRM: Any of the following DTCs are stored in the ECM: - P0037, P0038, P0057, P0058, P0139, P0159, P0141, P0161, P0137, P0157, P0138, P0158 ACTION: Refer to the FLOW CHART in this bulletin. See this bulletin for further detail.

BUICK, CHEVROLET, GMC · 2014-10-15

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Codes P0030, P0031, P0032, P0036, P0037, P0038, P0050, P0051, P0052, P0053, P0054, P0056, P0057, P0058, P0059, P0060, P0131,?P0132,?P0134,?P0137,?P0138,?P0140,?P0151, P0052, P0154, P0157, P0158,?P0160, P0443, and P0049. Technician also may find Emission 1 Fuse is open. Technician will need to inspect and repair any wires damage on the engine harness to the Bank 1 O2 sensor for chafing on the A/C hose coupling.

ACURA · 2014-03-31

Dealer message - American Honda (AHM) is investigating certain 2014 MDXs with a complaint of the Malfunction Indicator Lamp (MIL) on with the DTC P0158 (Front Secondary Heated Oxygen Sensor Circuit High Voltage) and/or P0138 (Rear Secondary Heated Oxygen Sensor Circuit High Voltage) stored. To fully understand the cause of this condition, AHM would like to collect specific parts from the vehicle prior to you attempting any further repair of any kind.