U0100 · メーカー技術情報

TOYOTA · 2022-08-10

TT: After jump-starting, the vehicle may experience a no-start condition and multiple DTCs including U010087. Upon investigation, it is found that the engine ECU has been damaged and needs to be replaced (Fig 1). In several cases, it was found that the cause of the ECU damage was improper jump starting. Further investigation found that ECU damage may occur if the jumper cables are hooked up on or around the engine ECU or ECU mounting bracket

ISUZU · 2022-06-17

Dealers, upfitters or bodybuilders may notice various warning lights on the dash illuminating and certain DTCs without an apparent cause during the initial installation and connection of telematics, GPS, and/or other aftermarket devices to the FMS system on certain 2022MY vehicles equipped with RPO I4H, DTCs that may occur are P1381, P1382, U2105, U1001, U0140, U0101, U0100, U0212, U0219, and U0028. These vehicles were configured with an incorrect module setup during the FMS installation at the port, which causes these lights and codes to set. Follow the service procedure below to validate that this incorrect configuration is the cause of these lights and codes and to reconfigure the Controller Area Network (CAN) Bus Interface.

FORD · 2022-04-22

Some 2021-2022 Mustang Mach-E vehicles built on or before 15-Mar-2022 may exhibit a Parking Brake Fault Service Now message in the instrument panel cluster (IPC) and DTCs C2007, C2008, C1034, U0293 and/or U0100 in the antilock brake system (ABS) module. This may be due to an open/corroded circuit near the rear caliper. To correct the condition, follow the Service Procedure to replace the electronic parking brake (EPB) connector.

TOYOTA · 2022-04-06

TT: After jump-starting, the vehicle may experience a no-start condition and multiple DTCs including U010087. Upon investigation, it is found that the engine ECU has been damaged and needs to be replaced (Fig 1). In several cases, it was found that the cause of the ECU damage was improper jump starting. Further investigation found that ECU damage may occur if the jumper cables are hooked up on or around the engine ECU or ECU mounting bracket

FORD, LINCOLN · 2021-12-21

Some 2020-2021 Aviator vehicles equipped with a 3.0L PHEV powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) U0100, P1A42 and/or P1A43 stored in battery energy control module (BECM). This may be due to software in the PCM. To correct the condition, follow the service procedure to perform a coordinated flash on the powertrain control module (PCM), secondary on-board diagnostic module c (SOBDMC), anti-lock braking system (ABS) module, BECM, and battery charger control module (BCCM).

FORD · 2021-11-17

Some 2021 Mustang Mach-E vehicles built on or before 09-Sep-2021 may exhibit an illuminated powertrain malfunction indicator (wrench) lamp and/or display the message Shift System Fault Service required with DTC U0103:87 stored in the secondary on board diagnostic module (SOBDMC). Some vehicles may also exhibit DTCs U0100:00, U0121, U0140, and/or U0155 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct the condition, follow the Service Procedure to reprogram the GSM.

VOLKSWAGEN · 2021-11-04

Diagnostic assistance for no start or no communication with ECM with DTC U0100 stored.

CHEVROLET, GMC · 2021-04-21

This Preliminary information communicates the following issues and directs dealership to inspect the engine harness for shorting. Some customers may comment on any of the following concerns: - SES MIL - No Start - No Crank - Engine runs rough - Reduced engine power - Erratic speedo - Blown Fuse(s): F46UA, F47UA, F51UA, F78UA, F85UA, F86UA, F87UA, and/or F90UA When checking for DTC's any combination may be found: C15AA P001A P2B00 P2B01 P2B03 P2B96 P001B P003D P0107 P018C P01E5 P01E6 P01E7 P0237 P0340 P0341 P0355 P0365 P037C P03F0 P0521 P0522 P0532 P0616 P077C P07BF P0707 P1101 P112F P146D P159F p16A0 p16A2 P171B P2122 P26E5 P2812 P2814 P2B53 P2C05 P2C08 P2C09 P2C0C P2C0D P2C10 P2C12 P2C15 P2C16 P2C19 P305E P3084 P3089 P308E P3093 P3094 P3095 P3098 P30B0 P30B3 P30CF U0073 U0100 U0101 U0140…

JEEP · 2021-04-16

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs have been set: P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). U0100 - Lost Communication With ECM/PCM. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P1CEA - Boost Side EVAP Purge System Performance. In addition, the customer may also experience the following: The vehicle will not crank if the ECM gets hotter than…

FIAT · 2021-04-16

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTChas been set: P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). U0100 - Lost Communication With ECM/PCM. The following DTCs have been changed from a one trip fault to a two trip fault: P0607 - ECU Internal Performance. In addition, the customer may also experience the following: The vehicle will not crank if the ECM gets hotter than 50 °C (122°F).

JEEP · 2021-04-16

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs have been set: P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). U0100 - Lost Communication With ECM/PCM. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P1CEA - Boost Side EVAP Purge System Performance. In addition, the customer may also experience the following: The vehicle will not crank if the ECM gets hotter than…

FIAT · 2021-04-16

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTChas been set: P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). U0100 - Lost Communication With ECM/PCM. The following DTCs have been changed from a one trip fault to a two trip fault: P0607 - ECU Internal Performance. In addition, the customer may also experience the following: The vehicle will not crank if the ECM gets hotter than 50 °C (122°F).

RAM · 2021-03-16

Flash: Hybrid Control Processor (HCP) Updates This bulletin involves updating the HCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). P1A26-00 - BPCM Hybrid Battery State Of Charge Performance. P0A7E-00 - Hybrid/EV Battery Pack Over Temperature. U1003-00 - ESP Can C Bus Performance. P2534-00 - Ignition Switch Run/Start Position Circuit Low. P0506 - Idle Speed Performance Lower Than Expected. P0507 - Idle Speed Performance Higher Than Expected. One Trip DTC Changed to a Two Trip DTC.P0AC6-00 - Hybrid/Ev Battery Temperature Sensor 2 Circuit Performance. P0ACB-00 - Hybrid/Ev Battery Temperature Sensor 3 Circuit…

RAM · 2021-03-16

Flash: Hybrid Control Processor (HCP) Updates This bulletin involves updating the HCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). P1A26-00 - BPCM Hybrid Battery State Of Charge Performance. P0A7E-00 - Hybrid/EV Battery Pack Over Temperature. U1003-00 - ESP Can C Bus Performance. P2534-00 - Ignition Switch Run/Start Position Circuit Low. P0506 - Idle Speed Performance Lower Than Expected. P0507 - Idle Speed Performance Higher Than Expected. One Trip DTC Changed to a Two Trip DTC.P0AC6-00 - Hybrid/Ev Battery Temperature Sensor 2 Circuit Performance. P0ACB-00 - Hybrid/Ev Battery Temperature Sensor 3 Circuit…

FORD · 2021-02-01

Some 2020-2021 Explorer vehicles equipped with a 10R60/10R80-MHT automatic transmission and built on or before 29-Oct-2020 may exhibit an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTCs) U0100, U0155, P166B, P0929, and/or P0919. The vehicle may also exhibit an illuminated powertrain malfunction (wrench) indicator lamp. This may be due to the software in the gear shift module (GSM). To correct the condition, reprogram the GSM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

FORD · 2020-12-24

Some 2020-2021 Explorer/Police Interceptor Utility vehicles equipped with a 3.3L hybrid engine and built on or before 21-Oct-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) U0100 stored in the battery energy control module (BECM). This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.

CHEVROLET, GMC · 2020-12-22

This Preliminary information communicates an issue with the engine wiring harness shorting at the left front cylinder head causing any of the following issues: - IPC gauges sweeping while driving - Several IPC warning messages and MIL displayed - Any combination of the following DTC's: U0073 U0100 U0101 U0121 U0128 U0129 U0131 U0140 U0146 U0422 U2413 P0107 P0117 P0119 P0641 C2A07

CHRYSLER · 2020-11-20

TBM (Telematics Box Module), DTC U0100-00 Lost Communication With ECM/PCM

CADILLAC, CHEVROLET, GMC · 2020-11-17

This Preliminary information communicates a customer concern of IPC gauges inoperative or fluctuate, No Start, No Crank, SIR Light / Service Airbag Message, Service Suspension Message, Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback, HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164, U0184, U0186, U0198, U0422. Dealer is instructed to check for logic lock of Serial Data Gateway Module or for Serial Data Gateway Module X1 and X2 connectors having terminal concerns and repair as needed.

CADILLAC, CHEVROLET, GMC · 2020-11-05

This Preliminary information communicates a customer concern of IPC gauges inoperative or fluctuate, No Start, No Crank, SIR Light / Service Airbag Message, Service Suspension Message, Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback, HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164, U0184, U0186, U0198, U0422. Dealer is instructed to check for logic lock of Serial Data Gateway Module or for Serial Data Gateway Module X1 and X2 connectors having terminal concerns and repair as needed.

FORD · 2020-10-20

Some 2020 Explorer vehicles may exhibit an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTCs) U0100, U0155, P166B, P0929, and/or P0919. The vehicle may also exhibit an illuminated powertrain malfunction (wrench) indicator lamp. This may be due to the software in the gear shift module (GSM). To correct the condition, reprogram the GSM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

CADILLAC, CHEVROLET, GMC · 2020-10-01

This Preliminary information communicates a customer concern of IPC gauges inoperative or fluctuate, No Start, No Crank, SIR Light / Service Airbag Message, Service Suspension Message, Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback, HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164, U0184, U0186, U0198, U0422. Dealer is instructed to check for logic lock of Serial Data Gateway Module or for Serial Data Gateway Module X1 and X2 connectors having terminal concerns and repair as needed.

FORD · 2020-09-03

Some 2020 Escape vehicles may exhibit an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTCs) U0100, U0401, P166B, P1753, P0929, and/or P0919. The vehicle may also exhibit an illuminated powertrain malfunction (wrench) indicator lamp. This may be due to the software in the gear shift module (GSM). To correct the condition, reprogram the GSM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part number 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

CHEVROLET · 2020-07-15

This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp (MIL) illuminated, intermittent service messages, Erratic Gauges and technician finding DTCs U0073, U0121, U0100 and/or U0101 set.

FORD, LINCOLN · 2020-06-22

Some 2020 Escape/Corsair/Explorer/Aviator vehicles may have diagnostic trouble code (DTC) U0100 stored in the audio front control module (ACM). This DTC will not cause observable conditions or warning indicators for the customer. If this DTC is detected during pre-delivery inspection (PDI) or while diagnosing unrelated conditions, it should be disregarded.

AUDI · 2020-06-15

This bulletin contains a software update for when the engine does not crank/start with the instrument cluster only partially turning at best. DTC U010000 may be stored or it may not.

JEEP · 2020-05-20

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set:U0100 - Lost Communication With ECM/PCM. P0456 - EVAP System Small Leak. If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P1CEA - Boost Side EVAP Purge System Performance. In addition, the customer may also experience the following: The vehicle will not crank if the ECM gets hotter than 50 °C (122 °F). Intermittent no-crank when first starting the vehicle.

FIAT · 2020-05-19

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DiagnosticTrouble Code (DTC) has been set:U0100 - Lost Communication With ECM/PCM. In addition, the customer may also experience the following: The vehicle will not crank if the ECM gets hotter than 50 °C (122°F).

CHEVROLET, GMC · 2020-05-07

This Preliminary information communicates an issue with the engine wiring harness shorting at the left front cylinder head causing any of the following issues: - IPC gauges sweeping while driving - Several IPC warning messages and MIL displayed - Any combination of the following DTC's: U0073 U0100 U0101 U0121 U0128 U0129 U0131 U0140 U0146 U0422 U2413 P0107 P0117 P0119 P0641 C2A07

JEEP · 2020-03-27

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs have been set:U0100 - Lost Communication With ECM/PCM. P0456 - EVAP System Small Leak. P1CEA - Boost Side EVAP Purge System Performance. In addition, the customer may also experience the following:The vehicle will not crank if the ECM gets hotter than 50 °C (122°F). Intermittent no-crank when first starting the vehicle.