MERCEDES-BENZ, MERCEDES-MAYBACH

LI80.20-P-078308

2026-03-23 · NHTSA 11030300

목록의 차량은 조사 단서입니다. 제조사 자료에서 엔진, 생산 기간, 소프트웨어 조건을 확인하세요.

제조사 요약

영어 원문

Complaint Depending on the identified problem (items 1-4), please implement the corresponding Remedy below (items 1-4): 1. KeylessGo sensor surfaces do not respond. Door handles can extend/retract if the key is used for locking/unlocking. No particular fault code. 2. Surface-flush door handle fails to retract and/or extend. One or more of the following fault codes are current and stored: B185D96; B185E96; B186196; B186296 The following values are present in the control unit log (A17/x): Motor_bridge_connection_fatal_error = True (for example, see attachment) OR Motor_bridge_wrong_direction_fatal_error = True (for example, see attachment) 3. Surface-flush door handle fails to retract and/or extend. One or more of the following fault codes are current and stored: B185D96; B185E96; B186196; B186296 The following values are present in the control unit log (A17/x): Motor_init_error_for_sensors = True (for example, see attachment) 4. Surface-flush door handle fails to retract and/or extend. The fault code B185911 is stored in the DCU (N69/X). Cause 1. Software bug. 2. Software robustness. 3. Software robustness. 4. The motor resistance is outside the tolerance range. Remedy Depending on the identified Complaint above (items 1-4), please implement the corresponding remedial actions (items 1-4): 1. Perform a reset of the corresponding 'KEYLESS GO' door handle control unit (A17/x) via XENTRY (for example see attachment) add-on is available (add-on 32204 for XENTRY version 06/25) Please use one of the following damage codes: 8213H73; 8219773; 8213K73; 8219873 2. Please process the guided fault check via XENTRY (Add-on 32485 for XENTRY version 06/25; Add-on 32486 for XENTRY version 09/25). In the event of a proposed SCN coding, it must be carried out and the faults must then be cleared. Please use one of the following SSLs: 8213H73; 8219773; 8213K73; 8219873 3. Please process the guided fault check via XENTRY (Add-on 32485 for XENTRY version 06/25; Add-on 32486 for XENTRY version 09/25). In the event of a proposed renewal of the bearing bracket, the corresponding bearing bracket must be replaced. Please use one of the following SSLs: 80A0D73; 80N0D73; 80N0E73; 80A0E73 4. The motor resistance is too low. Bearing bracket must be replaced. Please use one of the following SSLs: 80A0D73; 80N0D73; 80N0E73; 80A0E73 Please note that other published GI documents may also be valid for assessing the problem. For example: "LI72.10-P-074316 Flush-Mounted Door Handle Jams When It Is Pulled Out". Please also refer to SI72.00-P-0014A in WIS. If after the remedy points above are performed, the problem is still present, please submit a TIPS case to the PTS-Body/Chassis/Entertainment inbox. → In this case, store the damaged parts for further analyses.

제조사, 번호, 발행일, 전체 요약이 같은 등록만 묶고 원래 번호를 보존합니다. 과거 자료도 유지하며 확인된 명시적 후속판만 표시합니다. 1994년 이전 관계는 기본 결과와 분리합니다. 연식 미기재는 모든 연식 적용이 아닙니다.