P0300 · 제조사 기술 자료

BUICK, CHEVROLET · 2017-04-03

This Preliminary Information communication provides information to the technician about vehicles that may be running rough with a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P0300 set. Technician will need to perform an Engine Compression Testing in Service Information. If excessive leakage to the crankcase is isolated, check piston and cylinder wall condition. Technician should perform the repair per the level of damage. If the cylinder wall surface has not been compromised, only piston replacement is required.

JAGUAR · 2017-03-29

SITUATION: During an engine cold-start (coolant temperature at or below 75°C / 167°F), the engine may exhibit hard starting, rough idle, poor running, and/or an engine misfire. The engine Malfunction Indicator Lamp (MIL) may be illuminated with Diagnostic Trouble Code (DTC) P0316 stored in the Powertrain Control Module (PCM) and one or more misfire code(s) P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, and/or P0308.

ACURA · 2017-03-22

"DEALER MESSAGE - AMERICAN HONDA (AHM) IS INVESTIGATING CERTAIN 2016 MDX WITH A CLIENT COMPLAINT OF THE MALFUNCTION INDICATOR LAMP (MIL) ON WITH THE DTC P0300 (RANDOM MISFIRE DETECTED), P0301 (NO. 1 CYLINDER MISFIRE DETECTED), P0302 (NO. 2 CYLINDER MISFIRE DETECTED), P0303 (NO. 3 CYLINDER MISFIRE DETECTED), P0304 (NO. 4 CYLINDER MISFIRE DETECTED), P0305 (NO. 5 CYLINDER MISFIRE DETECTED) AND/OR P0306 (NO. 6 CYLINDER MISFIRE DETECTED) STORED. TO FULLY UNDERSTAND THE CAUSE OF THIS CONDITION, AHM WOULD LIKE TO INSPECT THE VEHICLE PRIOR TO YOU ATTEMPTING A REPAIR OF ANY KIND."

FORD · 2017-03-14

SOME 2014-2017 FUSION AND 2017 ESCAPE VEHICLES EQUIPPED WITH A 1.5L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE AND AN ODOMETER READING 16,000 KM (10,000 MILES) OR ABOVE MAY EXHIBIT LOW COOLANT, WHITE EXHAUST SMOKE AND MAY ALSO EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0217, P0300, P0301, P0302, P0303, P0304, P0316 AND/OR P1299. THIS CONDITION MAY BE DUE TO AN INTAKE MANIFOLD BOLT BACKING OUT CAUSING DAMAGE TO THE CHARGE AIR COOLER (CAC). FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION

MAZDA · 2017-03-02

When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory.?P0300 - Random misfire detected ?P0301 - Cylinder No.1 misfire detected ?P0302 - Cylinder No.2 misfire detected ?P0303 - Cylinder No.3 misfire detected ?P0304 - Cylinder No.4 misfire detected This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow.

CHEVROLET · 2017-02-28

This Preliminary Information communication provides information to the technician about vehicles that may be running rough with a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P0300 set. Technician will need to perform an Engine Compression Testing in Service Information. If excessive leakage to the crankcase is isolated, check piston and cylinder wall condition. Technician should perform the repair per the level of damage. If the cylinder wall surface has not been compromised, only piston replacement is required.

BUICK, CHEVROLET · 2017-02-23

This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Technician will need to utilize engine controls schematics to compare the Fuel Injector Control Circuit wire colors to determine if the wires are reversed. If this concern is found, inspect the related harnesses and terminals for signs damage due to the misrouting and repair.

FORD · 2017-02-20

SOME 2017 F-SUPER DUTY, E-SERIES, F53 MOTORHOME, F59 CHASSIS, F-650/750 VEHICLES EQUIPPED WITH A 6.8L ENGINE WITH AN ENGINE BUILT ON 10-SEP-2016 AND THROUGH 15-FEB-2017 MAY EXHIBIT MULTIPLE MISFIRE DIAGNOSTIC TROUBLE CODES (DTCS) P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0306, P0307, P0308, P0309, P0309 AND/OR P0310. THIS MAY BE DUE TO AN UNDER TORQUED CRANKSHAFT PULLEY BOLT. BEFORE ATTEMPTING ANY DIAGNOSIS OR REPAIRS, SUSPECT UNDER TORQUED CRANKSHAFT PULLEY BOLT AS THE ISSUE.

FORD, LINCOLN · 2017-02-07

SOME 2017 MKZ/CONTINENTAL/FUSION VEHICLES EQUIPPED WITH THE 2.7L/3.0L ENGINE AND BUILT ON OR BEFORE 6-OCT-2016 MAY EXHIBIT A ROUGH IDLE IN NEUTRAL OR PARK AT NORMAL OPERATING TEMPERATURE OR AFTER A HOT RESTART, WHITE OR BLUE SMOKE FROM THE EXHAUST, EXCESSIVE OIL CONSUMPTION AND/OR AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0300, P0301, P0302, P0303, P0304, P0305, P0306 AND/OR P0316. SUSPECT THE CYLINDER HEADS AS THE CAUSE FOR THIS ISSUE. IF THE VEHICLE ALSO EXHIBITS P0524 AND/OR P06DD SUSPECT THE LONG BLOCK AS THE CAUSE FOR THIS ISSUE.

FORD, LINCOLN · 2017-02-07

SOME 2016 EDGE/MKX VEHICLES EQUIPPED WITH A 2.7L ENGINE AND BUILT ON 1-APR-2016 AND THROUGH 1-OCT-2016 MAY EXHIBIT A ROUGH IDLE IN NEUTRAL OR PARK AT NORMAL OPERATING TEMPERATURE OR AFTER A HOT RESTART, WHITE OR BLUE SMOKE FROM THE EXHAUST, EXCESSIVE OIL CONSUMPTION AND/OR AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0300, P0301, P0302, P0303, P0304, P0305, P0306 AND/OR P0316. SUSPECT THE CYLINDER HEADS AS THE CAUSE FOR THIS ISSUE. IF THE VEHICLE ALSO EXHIBITS P0524 AND/OR P06DD SUSPECT THE LONG BLOCK AS THE CAUSE FOR THIS ISSUE.

CHEVROLET · 2017-01-25

This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to…

CHEVROLET · 2017-01-20

This engineering informational bulletin ends the need for information from the field on vehicles that have the condition of Rough Running Engine with Malfunction Indicator Lamp On and DTC P0300 Set.

FORD · 2017-01-18

SOME 2016 F-150 VEHICLES EQUIPPED WITH A 2.7L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE AND BUILT ON 1-APR-2016 AND THROUGH 1-OCT-2016 MAY EXHIBIT WHITE OR BLUE SMOKE FROM THE EXHAUST, ROUGH IDLE IN NEUTRAL OR PARK AT NORMAL OPERATING TEMPERATURE OR AFTER A HOT RESTART. THE VEHICLE MAY ALSO EXHIBIT DIAGNOSTIC TROUBLE CODE (DTC) P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0316, P0524 AND/OR P06DD WITH THE EXCESSIVE OIL CONSUMPTION. OIL CONSUMPTION MAY BE 1 LITER (1 QUART) IN LESS THAN 4,800 KM (3,000 MILES). FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THIS CONDITION.

MAZDA · 2017-01-13

When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit/0 degrees Celsious). Some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. *P0300 - Random misfire detected *P0301-Cylinder No.1 misfire detected *P0302 Cylinder No.2 misfire detected *P0303-Cylinder No.3 misfire detected *P0304 Cynlinder No.4 misfire Detected This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow. Customers having this cocern should have their vehicle repaired using the ffollowifng repair procedure.

BUICK, CADILLAC, GMC · 2017-01-13

This engineering information bulletin is requesting information from the field on vehicles that have the condition of Engineering Information — Repeat Malfunction Indicator Lamp (MIL) on with DTC P0300 (Engine Misfire Detected)

BUICK, CADILLAC, CHEVROLET, GMC, HUMMER, PONTIAC, SAAB · 2016-12-23

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

FORD · 2016-12-09

SOME 2014-2016 TRANSIT CONNECT VEHICLES EQUIPPED WITH THE 2.5L ENGINE MAY EXHIBIT A CONSTANT OR INTERMITTENT ILLUMINATED MIL WITH VARIOUS DRIVABILITY ISSUES AND ONE OR MORE OF THE FOLLOWING DTCS: P0010, P0103, P0104, P0122, P0131, P0135, P0137, P0141, P0201-P0204, P0217, P0222, P0223, P025A, P0300, P0301-P0304, P0316, P0351-P0354, P0400, P0403, P0443, P1285, P1289, P128A, P1299, P2101, P2107, P2111, P2112, P2122, P2127 AND/OR U0109. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

RAM · 2016-11-17

Flash: Powertrain System Improvements/EnhancementsThis bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following (DTCs) have been set:P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible (14&15 MY). P0116 - Engine Coolant Temperature Sensor Performance (14&15 MY). P0335 - Crankshaft Position Sensor Circuit (14&15 MY). U1424-00 - Implausible Engine Torque Signal Received (14&15 MY). P1239 - Engine Oil Temperature Too Low (15 MY Sales Code ERB). P0300 - Multiple Cylinder Misfire.P0456 - EVAP System Small Leak.P0607 - ECU Internal Performance.P2096 -…

JEEP · 2016-11-15

Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find, one or more of the following DTCs set in the PCM memory: P0116 - Coolant Temperature Sensor Performance. P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. U1424 - Implausible Engine Torque Signal Received. P1239 - Engine Oil Temperature Too Low, set in cold ambient temperatures. P0298 - Engine Oil Temperature Too High, set in cold ambient temperatures. P0300 - Multiple Cylinder Misfire, may set at a 1-2 upshift above 6000 RPM.In addition, some customers may…

BUICK, CHEVROLET · 2016-11-15

This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Technician will need to utilize engine controls schematics to compare the Fuel Injector Control Circuit wire colors to determine if the wires are reversed. If this concern is found, inspect the related harnesses and terminals for signs damage due to the misrouting and repair.

SUBARU · 2016-11-08

New Alternator Assembly. This bulletin provides a procedure for diagnosis and repair of DTC P0300 which may result from fluctuation of the alternator?s current output outside of the specified limits.

BUICK, CHEVROLET · 2016-11-01

This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Technician will need to utilize engine controls schematics to compare the Fuel Injector Control Circuit wire colors to determine if the wires are reversed. If this concern is found, inspect the related harnesses and terminals for signs damage due to the misrouting and repair.

TOYOTA · 2016-10-14

TSB: Some 2013 ? 2015 Prius PHV, Prius and 2013 ? 2016 Prius V vehicles may exhibit a vibration due to rough idle and/or tapping noise from the HV transaxle at cold start. The check engine light may also illuminate with (DTC) P0300, P0301, P0302, P0303, P0304 (Random/Multiple Cylinder Misfire Detected). The Engine Control Module/ECM (SAE Term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition occurring. Follow the Repair Procedure in this bulletin to address this condition.

BUICK, CHEVROLET · 2016-09-30

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY BE RUNNING ROUGH WITH A MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE P0300 SET. TECHNICIAN WILL NEED TO PERFORM AN ENGINE COMPRESSION TESTING IN SERVICE INFORMATION. IF EXCESSIVE LEAKAGE TO THE CRANKCASE IS ISOLATED, CHECK PISTON AND CYLINDER WALL CONDITION. TECHNICIAN SHOULD PERFORM THE REPAIR PER THE LEVEL OF DAMAGE. IF THE CYLINDER WALL SURFACE HAS NOT BEEN COMPROMISED, ONLY PISTON REPLACEMENT IS REQUIRED.

CADILLAC, CHEVROLET, GMC · 2016-09-23

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP ON AND DIAGNOSTIC TROUBLE CODE P0300 - P0308 MAY SET. TECHNICIAN WILL INSPECT FOR LOSE SPARKPLUG WIRE. IF A SPARK PLUG WIRE IS FOUND LOSE CHECK FOR A MISSING “C” CLIP ON THE WIRE END FOR THE IGNITION COIL. IF THE CLIP IS MISSING REPLACE THE WIRE.

MAZDA · 2016-09-22

CHECK ENGINE LIGHT ON WITH DTC P0300-P0304

CHRYSLER, DODGE · 2016-09-07

Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set: U0140 - Lost Communication With Body Control Module. P0441 - EVAP Purge System Performance. P0420 - Catalyst Efficiency (Bank 1). P0430 - Catalyst Efficiency (Bank 2). P0133 - O2 Sensor 1/1 Slow Response. P0153 - O2 Sensor 2/1 Slow Response. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P113D - O2 Sensor 1/1 Slow…

LINCOLN · 2016-09-07

Some 2017 MKZ vehicles equipped with 3.0L engine and built on or before 8-Aug-2016 may exhibit a rough idle in neutral or park at normal operating temperature or after a hot restart with or without diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304, P0305, P0306 and/or P0316. Reprogram the PCM to the latest calibration using Integrated Diagnostic System (IDS) release 102.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.

DODGE, RAM · 2016-09-03

Flash: Powertrain Diagnostic And System Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: U0140 - Lost Communication With Body Control Module (BCM) (12 MY DJ only) P0300 - Multiple Cylinder Misfire.The P0300 improvement only applies to vehicles using a block heater in ambient temperatures greater than -20°F(-29°C). P2008 - Short Runner Valve (SRV) Control Circuit. P1004 - Short Runner Valve Control Performance. P2016 - Intake Manifold Runner Position Sensor Circuit Low. P2017 - Intake Manifold Runner Position…

BUICK, CHEVROLET · 2016-09-02

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY BE RUNNING ROUGH WITH A MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE P0300 SET. TECHNICIAN WILL NEED TO PERFORM AN ENGINE COMPRESSION TESTING IN SERVICE INFORMATION. IF EXCESSIVE LEAKAGE TO THE CRANKCASE IS ISOLATED, CHECK PISTON AND CYLINDER WALL CONDITION. TECHNICIAN SHOULD PERFORM THE REPAIR PER THE LEVEL OF DAMAGE. IF THE CYLINDER WALL SURFACE HAS NOT BEEN COMPROMISED, ONLY PISTON REPLACEMENT IS REQUIRED.