보기

P0562 · 제조사 기술 자료

목록의 차량은 조사 단서입니다. 제조사 자료에서 엔진, 생산 기간, 소프트웨어 조건을 확인하세요.

P0562 ← 이 코드는 무엇을 뜻하나요?

36 결과

37930.1.0 ↗

VOLVO · 2026-09-19

This is a TJ - Text only no attachments - If a customer experiences a DIM message stating "Propulsion System Service Required" and DTC IGM P056200 is set, please follow the advice under "Service". Do not replace any parts. This DTC is set due to low 12-volt system voltage. Start by following the steps

PIT6522 ↗

CADILLAC, CHEVROLET, GMC · 2026-06-10

This PI advises dealers that if the K160 Brake System Control Module sets DTC P0606 along with P0562 and/or P25A2, additional diagnostic aids should be followed before replacing parts. The PI provides guidance to inspect for low voltage conditions, wiring, terminal concerns, and module communication issues that may cause false or intermittent EBCM DTCs.

37103.6.0 ↗

VOLVO · 2026-05-13

This is a Technical Journal: Check Engine Light/DIM message and ISGM DTC P056200 or in combination with all the DTCs

TSB_2076994_8 ↗

AUDI · 2026-05-08

This bulletin provides information when there are DTCs for the 48V starter generator; P0A1A00 P19F800 P0A1E00 U014600 U300100 P10F300 P056200 P056100 P065200 P069800.

PIT6347B ↗

CADILLAC, CHEVROLET, GMC · 2026-03-26

This Preliminary information communicates an issue with ABS SES MIL / Service Brake System / Service StabiliTrak / BSCM DTC P0606 P0562 and dealers to perform additional battery and connection testing.

37103.4.0 ↗

VOLVO · 2026-03-07

This is a Technical Journal: Check Engine Light/DIM message and ISGM DTC P056200 or in combination with all the DTCs

TSB_2076994_6 ↗

AUDI · 2026-01-05

This bulletin provides information when there are DTCs for the 48V starter generator; P0A1A00 P19F800 P0A1E00 U014600 U300100 P10F300 P056200 P056100 P065200 P069800.

TJ37555.1.0-2025-11-18 ↗

VOLVO · 2025-11-19

This is a TJ - no attachments - If the engine cannot be remote started in the Volvo Cars app and the "Check Engine Light" is on in the DIM, together with DTC ISGM P056200, or in combination with the DTCs listed below, please follow the advice under "Service".Do not replace the ISGM. The ISGM is just a messenger to detect issues in the 48-volt system. The symptom occurs when the ERS attempt via the Volvo Cars app is made immediately after the engine has been turned off and the car has been locked.

TJ37103.3.0-2025-11-13 ↗

VOLVO · 2025-11-19

This is a Technical Journal: Check Engine Light/DIM message and ISGM DTC P056200 or in combination with all the DTCs

37103 ↗

VOLVO · 2025-07-23

This is a Technical Journal: Check Engine Light/DIM message and ISGM DTC P056200.

PIT6347A ↗

CADILLAC, CHEVROLET, GMC · 2025-03-11

This Preliminary information communicates an issue with ABS SES MIL / Service Brake System / Service StabiliTrak / BSCM DTC P0606 P0562 and dealers to perform additional battery and connection testing.

PIT6347 ↗

CADILLAC, CHEVROLET, GMC · 2025-02-25

This Preliminary information communicates an issue with ABS SES MIL / Service Brake System / Service StabiliTrak / BSCM DTC P0606 P0562 and engineering is currently investigating.

24-NA-050 ↗

CHEVROLET, GMC · 2025-01-15

This technical bulletin provides repair information to correct a customer concern of Silverado and Sierra Setting DTC P0606 and either DTC P0562 or P0563.

24-NA-050 ↗

CHEVROLET, GMC · 2024-08-01

This technical bulletin provides repair information to correct a customer concern of Silverado and Sierra Setting DTC P0606 and either DTC P0562 or P0563.

24-NA-050 ↗

CHEVROLET, GMC · 2024-06-29

This technical bulletin provides repair information to correct a customer concern of Silverado and Sierra Setting DTC P0606 and either DTC P0562 or P0563.

24-NA-050 ↗

CHEVROLET, GMC · 2024-03-11

This technical bulletin provides repair information to correct a customer concern of Silverado and Sierra Setting DTC P0606 and either DTC P0562 or P0563.

S2208000075 ↗

JEEP · 2022-03-17

Check Engine Light Is On, No Start. DTC?s P00FD, P0562, P26F3

SSM 50151 ↗

FORD, LINCOLN · 2021-09-24

Some 2020-2021 Explorer/Aviator Hybrids, 2021 Corsair Hybrid, 2021 F-150 PowerBoost, and 2021 Mustang Mach-E vehicles may exhibit a no-start with a Stop Safely Now warning message in the instrument panel cluster (IPC). The vehicle may have one or more of the following DTCs P0A23, P0A6F, P0A72, P0A75, P0A71, P0A74, P0A77, P0DFA, P06B1, P0A47, P1A0E set by the secondary on-board diagnostic module C (SOBDMC) or secondary on-board diagnostic module B (SOBDMB). This may be due to a drop in the 12-volt circuit. These DTCs will often occur at vehicle key-on and may be difficult to reproduce. Before replacement of the SOBDMC or SOBDMB, diagnose any low voltage DTCs (P0562, U3003) in other modules in the 12V system. If low voltage (less than 10V) is observed in these DTCs snapshot, diagnose the…

0803721 ↗

RAM · 2021-03-16

Flash: Hybrid Control Processor (HCP) Updates This bulletin involves updating the HCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). P1A26-00 - BPCM Hybrid Battery State Of Charge Performance. P0A7E-00 - Hybrid/EV Battery Pack Over Temperature. U1003-00 - ESP Can C Bus Performance. P2534-00 - Ignition Switch Run/Start Position Circuit Low. P0506 - Idle Speed Performance Lower Than Expected. P0507 - Idle Speed Performance Higher Than Expected. One Trip DTC Changed to a Two Trip DTC.P0AC6-00 - Hybrid/Ev Battery Temperature Sensor 2 Circuit Performance. P0ACB-00 - Hybrid/Ev Battery Temperature Sensor 3 Circuit…

08-037-21 ↗

RAM · 2021-03-16

Flash: Hybrid Control Processor (HCP) Updates This bulletin involves updating the HCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). P1A26-00 - BPCM Hybrid Battery State Of Charge Performance. P0A7E-00 - Hybrid/EV Battery Pack Over Temperature. U1003-00 - ESP Can C Bus Performance. P2534-00 - Ignition Switch Run/Start Position Circuit Low. P0506 - Idle Speed Performance Lower Than Expected. P0507 - Idle Speed Performance Higher Than Expected. One Trip DTC Changed to a Two Trip DTC.P0AC6-00 - Hybrid/Ev Battery Temperature Sensor 2 Circuit Performance. P0ACB-00 - Hybrid/Ev Battery Temperature Sensor 3 Circuit…

PIT5634 ↗

CHEVROLET, GMC · 2018-11-14

This Preliminary information communicates and issue with a customer concern of a SES MIL, Reduced Engine Power, Service Brake System, and/or Speed Limited message, a lack of brake assist making the brake pedal hard and DTC P0606. These issues can be caused by a low voltage conditions, but the EBCM incorrectly sets a DTC P0606 for a Control Module Processor Performance error. If the SI diagnostics are followed for DTC P0606 it can lead to a misdiagnosis and an incorrect repair. Dealers are advised to inspect for a low voltage condition and follow SI diagnostics for DTC P0562 "System Voltage Low". Engineering is trying to determine next steps in the resolution of this issue. It will likely be an update to SI or a change to the EBCM Calibration or both.

PIT5634 ↗

CHEVROLET, GMC · 2018-10-01

This Preliminary information communicates and issue with acustomer concern of a SES MIL, Reduced Engine Power, Service Brake System, and/orSpeed Limited message,a lack of brake assist making the brake pedal hard andDTCP0606. These issues can be caused by a low voltage conditions, but the EBCM incorrectly sets a DTC P0606 for aControl Module Processor Performance error. If the SI diagnostics are followed for DTC P0606 it can leadto amisdiagnosis and an incorrect repair. Dealers are advised to inspect for a low voltage condition and follow SI diagnostics forDTC P0562 "System Voltage Low". Engineering is trying to determine next steps in the resolution of this issue. It will likely be an update to SI or a change to the EBCM Calibration or both.

A16-026 ↗

HONDA · 2017-06-30

Servicenews article - While running an all DTC check with the i-HDS, are you seeing any of these DTCs with no other DTCs listed, yet the MIL is off and there?s no apparent symptom? ? DTC P0562 (battery condition monitor module power source circuit unexpected voltage) ? DTC P0562 (generator motor control module system low voltage) ? DTC P0562 (traction motor control module system low voltage)

BJA50809 ↗

ACURA · 2017-06-29

Servicenews article - While running an all DTC check with the i-HDS, are you seeing DTC P0562 (battery condition monitor module power source circuit unexpected voltage) with no other DTCs listed, yet the MIL is off and there?s no apparent symptom? If so, chances are there?s nothing wrong with the vehicle. Just clear the DTC, and recheck by cycling the ignition three times.

0801315 ↗

JEEP · 2015-02-13

Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: ? A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the Technician may find DTC U0216 Lost Communication With Driver Door Switch. ? Intermittent No Start condition Without any DTCs (Vehicles with steering column lock, only). ? U1220-87 - Lost Steering Lock Request Message - Missing Message. ? U1517-87 - Body Controller Secret Code - Missing Message. ? B2199-17 - Battery Voltage - Circuit Voltage Above Threshold, set in the BCM. ? Day Time Running Lamps (DRL) will not turn on until the vehicle speed is 2 MPH…

08-013-15 ↗

JEEP · 2015-02-13

Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: ? A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the Technician may find DTC U0216 Lost Communication With Driver Door Switch. ? Intermittent No Start condition Without any DTCs (Vehicles with steering column lock, only). ? U1220-87 - Lost Steering Lock Request Message - Missing Message. ? U1517-87 - Body Controller Secret Code - Missing Message. ? B2199-17 - Battery Voltage - Circuit Voltage Above Threshold, set in the BCM. ? Day Time Running Lamps (DRL) will not turn on until the vehicle speed is 2 MPH…

1803014REVB ↗

RAM · 2014-12-20

Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel.Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From P0201 - P0206 - Fuel Injector X Circuit/Open. P049D - EGR Control Position Exceeding Learning Limit. P0711 - Transmission Temperature Sensor Performance. P0712 - Transmission Temperature Sensor Low. P0713 - Transmission Temperature Sensor High. P0714 - Transmission Temperature Sensor Intermittent. P0740 - TCC Out Of Range. P0869 - Line Pressure High. P0933 -…

0811114 ↗

JEEP · 2014-12-20

Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the Technician may find DTC U0216 Lost Communication With Driver Door Switch. Without any DTCs (Vehicles with steering column lock, only). U1220-87 - Lost Steering Lock Request Message - Missing Message. U1517-87 - Body Controller Secret Code - Missing Message. B2199-17 - Battery Voltage - Circuit Voltage Above Threshold, set in the BCM. Day Time Running Lamps (DRL) will not turn on until the vehicle speed is 2 MPH (3 KPH), (Manual Transmission only). Puddle…

18-030-14 REV. B ↗

RAM · 2014-12-20

Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel.Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201- P0206 - Fuel Injector X Circuit/Open P049D- EGR Control Position Exceeding Learning Limit P0711- Transmission Temperature Sensor Performance P0712- Transmission Temperature Sensor Low P0713- Transmission Temperature Sensor High P0714- Transmission Temperature Sensor Intermittent P0740- TCC Out Of Range P0869- Line…

08-111-14 ↗

JEEP · 2014-12-20

Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the Technician may find DTC U0216 Lost Communication With Driver Door Switch. Without any DTCs (Vehicles with steering column lock, only). U1220-87 - Lost Steering Lock Request Message - Missing Message. U1517-87 - Body Controller Secret Code - Missing Message. B2199-17 - Battery Voltage - Circuit Voltage Above Threshold, set in the BCM. Day Time Running Lamps (DRL) will not turn on until the vehicle speed is 2 MPH (3 KPH), (Manual Transmission only). Puddle…