U0100 · 제조사 기술 자료

RAM · 2016-04-23

Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P2281 - Air Leak Between MAF And Throttle…

JEEP · 2016-04-02

Harness Repair Or Replacement For No Start Or Stiff Steering This bulletin involves inspecting the wire harness and installing mastic patch. If rub through is visible replace wire harness. A small number of customers may experience a no start condition, stiff steering or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs): · U0131 - Lost Communication With Power Steering Control Module. · U0100-00 - Lost Communication With ECM/PCM. · P0512-00 - Starter Request Circuit.

FORD · 2016-03-16

DPS6 - no satart and/or transmission engagement or loss of power with DTCS u0100, U00101, U1013, U3003 AND/OR P0606

FORD · 2016-03-16

DPS6 - NO START AND/OR TRANSMISSION ENGAGEMENT OR LOSS OF POWER WITH DTCS U0100, U0101, U1013, U3003 AND/OR P0606 ISSUE Some 2011-2016 Fiesta and 2012-2016 Focus vehicles equipped with a DPS6 transmission may exhibit intermittent concerns of loss of transmission engagement while driving, intermittent no start or a loss of power. These symptoms are usually accompanied by an illuminated Check Engine lamp. Additional symptoms may include messages in the message center indicating hill start assist is not available, that parking aid malfunction/service is required or the transmission PRNDL/S gear selector on the instrument cluster may flash. Diagnostic trouble codes (DTCs) U0100, U0101, U1013, U3003 and/or P0606 will be present or stored in the powertrain control module (PCM) memory.

CADILLAC · 2016-03-14

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles with a no crank concern or they are unable to remove their key from the ignition lock cylinder may find Diagnostic Trouble Codes P0318, P1629, U1040, U1064, U1153, U1192, and U1300 stored in the Engine Control Module. Other Class 2 modules may have a U0100 and/or U1000 code stored. These concerns may be caused by an Ignition 1 Power Feed (circuit 5290) or Class 2 (circuit 1807) wiring concern to the Engine Control Module. If the electrical center ignition relay feedback parameter in the Engine Control Module is not battery voltage, measure the voltage at the Engine Control Module fuse in the under-hood fuse block. If voltage is less than battery voltage, check to make…

JAGUAR · 2016-02-22

"SITUATION: THE ENGINE MAY NOT CRANK/START AND THE VEHICLE MAY EXHIBIT A WARNING LIGHT OR WARNING LIGHTS ON THE INSTRUMENT PANEL. UPON FURTHER DIAGNOSIS, THE TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE (DTC) U0100-00 LOGGED IN VARIOUS CONTROL MODULES, NO COMMUNICATION WITH THE POWERTRAIN CONTROL MODULE (PCM), IS UNABLE TO CLEAR THE DTC. THIS MAY RESULT IN THE REPLACEMENT OF THE PCM. CAUSE: THIS MAY BE CAUSED BY INTERNAL FAILURE OF THE PCM."

CHEVROLET · 2016-01-29

Crank / No Start ? DTC U0100, U1000, B2193 Stored

CHEVROLET · 2016-01-29

15169B - CUSTOMER SATISFACTION PROGRAM (REVISED SERVICE PROCEDURE). VEHICLES MAY EXHIBIT A CONDITION IN WHICH THE VEHICLE ENGINE WILL CRANK BUT NOT START. A REVERSED WIRE IN THE ENGINE EGI HARNESS CAN LEAD TO AN IGNITION SNEAK CIRCUIT, WHICH CAN PREVENT THE ENGINE CONTROL MODULE FROM COMMANDING A SPARK AT START-UP. DURING THE CRANK / NO START EVENT, A MALFUNCTION INDICATOR LAMP WILL BE ILLUMINATED, AND THE VEHICLE WILL STORE THE FOLLOWING CODE: U0100, U1000, AND B2193. DEALERS ARE TO REVISE THE ENGINE EGI HARNESS.

CADILLAC, CHEVROLET, GMC · 2015-11-12

This Preliminary Information communication provides information to the technician for a reduced power message, steering assist, engine stall or the instrument panel, radio, and or Heater-Vent-Air Conditioning go blank with multiple diagnostic trouble codes. If any of the following diagnostic trouble codes U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, U1510, U0073, B127B, B2605, B3600,C0800, U0428, and U0452 set in the vehicle. Check the body control module ground at the G218 location. The front dash insulator mat may be trapped between the ground eyelet and the body stud. Remove the round nut and eyelet and cut the front dash insulator mat away from the ground stud so it no longer interferes with the ground stud and reinstall the eyelet and ground nut.

RAM · 2015-11-07

Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for the following conditions. The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: ? U1A24 - Lost Communication With Ammonia Sensor. Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: ? P0201 - P0206 - Fuel Injector X Circuit/Open. ? P049D - EGR Control Position Exceeding Learning Limit. ? P0711 - Transmission Temperature Sensor Performance. ? P0712 - Transmission Temperature Sensor Low. ? P0713 -…

CHEVROLET, GMC · 2015-11-02

This Preliminary Information communication provides information to the technician about vehicles that may have a Diagnostic Trouble Code U0100 and or U0101 set in the Body Control Module when checking for codes. Disregard Diagnostic Trouble Code U0100 and or U0101 set in the Body Control Module unless it is also set in other controllers.

CHEVROLET, GMC · 2015-09-21

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.

RAM · 2015-07-25

Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for the following conditions. The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: ? U1A24 - Lost Communication With Ammonia Sensor. Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: ? U110E - Lost Ambient Temperature Message. ? P0201 - P0206 - Fuel Injector X Circuit/Open. ? P049D - EGR Control Position Exceeding Learning Limit. ? P0711 - Transmission Temperature Sensor Performance. ? P0712 -…

CADILLAC, CHEVROLET, GMC, HUMMER · 2015-06-25

This technical bulletin provides repair information to correct customer concerns of loss of high speed GMLAN communications, intermittent no crank, IP gauge fluctuation, intermittent door lock cycling /chime operation, various IP warning lamps illuminated, transmission may not shift, communication DTCs U0073, U0100, U0101, U0102, U0109, U0121 or U0140 set.

CHEVROLET, GMC · 2015-06-01

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.

CADILLAC · 2015-05-13

This Preliminary Information communication provides information to the technician about vehicles with the Service Engine Soon light is on, Reduced engine power message, no crank, multiple warning lights on, transmission shifts hard, or the door locks cycle while driving. The Transmission Control Module or Engine Control Module may not communicate. With Diagnostic Trouble Codes C0242, C0561, P0575, P0615, P0700, P0856, P1629, P2544, U0073, U0074, U0100, U0109, U0121, U0140, U2100, U2105, and / or U2106 stored. The technician is to inspect the transmission X1 connector terminals for loose or poor fit. Disconnect the X1 connector and carefully tug on each wire to insure pins are fully seated. A side load on the wires may also cause a false positive lock. Technician is to repair the…

CADILLAC, CHEVROLET, GMC · 2015-05-04

This Preliminary Information communication provides information to the technician for a reduced power message, steering assist, engine stall or the instrument panel, radio, and or Heater-Vent-Air Conditioning go blank with multiple diagnostic trouble codes. If any of the following diagnostic trouble codes U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, U1510, U0073, B127B, B2605, B3600,C0800, U0428, and U0452 set in the vehicle. Check the body control module ground at the G218 location. The front dash insulator mat may be trapped between the ground eyelet and the body stud. Remove the round nut and eyelet and cut the front dash insulator mat away from the ground stud so it no longer interferes with the ground stud and reinstall the eyelet and ground nut.

CHEVROLET, GMC · 2015-05-01

This Preliminary Information communication provides information to the technician for vehicles with a malfunction indicator lamp on, service stabilitrak, power steering or vehicle soon message displayed on the drivers information center. The technician may find the following diagnostic trouble codes U0073, U0100, U0101, U0121 U0140 C0045, C0050 in the body control module, electronic brake control module, engine control module, or the transmission control module. There may be multiple loss of communication codes current or history for high speed General Motors Local Area Network. Inspect the connections at connector X411 for corrosion due to the location of the connector under the vehicle by the rear wheel.

CHEVROLET · 2015-04-20

15169A - CUSTOMER SATISFACTION PROGRAM (REVISED TO UPDATE THE CRIMPING TOOL NUMBER IN THE SERVICE PROCEDURE). CERTAIN 2015 MODEL YEAR CHEVROLET CITY EXPRESS MODEL VEHICLES MAY EXHIBIT A CONDITION IN WHICH THE VEHICLE ENGINE WILL CRANK BUT NOT START. A REVERSED WIRE IN THE ENGINE EGI HARNESS CAN LEAD TO AN IGNITION SNEAK CIRCUIT, WHICH CAN PREVENT THE ENGINE CONTROL MODULE FROM COMMANDING A SPARK AT START-UP. DURING THE CRANK / NO START EVENT, A MALFUNCTION INDICATOR LAMP WILL BE ILLUMINATED, AND THE VEHICLE WILL STORE THE FOLLOWING CODE: U0100, U1000, AND B2193. DEALERS ARE TO REVISE THE ENGINE EGI HARNESS.

CHEVROLET · 2015-03-26

15169 - CUSTOMER SATISFACTION PROGRAM. CERTAIN VEHICLES MAY EXHIBIT A CONDITION IN WHICH THE VEHICLE ENGINE WILL CRANK BUT NOT START. A REVERSED WIRE IN THE ENGINE EGI HARNESS CAN LEAD TO AN IGNITION SNEAK CIRCUIT, WHICH CAN PREVENT THE ENGINE CONTROL MODULE FROM COMMANDING A SPARK AT START-UP. DURING THE CRANK / NO START EVENT, A MALFUNCTION INDICATOR LAMP WILL BE ILLUMINATED, AND THE VEHICLE WILL STORE THE FOLLOWING CODE: U0100, U1000, AND B2193. DEALERS ARE TO REVISE THE ENGINE EGI HARNESS.

CHEVROLET · 2015-02-09

This Preliminary Information communication provides information to the technician about vehicles that may have an engine will crank or turn over but will not start and/or once the engine is running the Service Engine Soon Malfunction Indicator Lamp will illuminate. Technician may find Diagnostic Trouble Codes U0100 and U1000 in multiple high speed modules and the Body Control Module may have B2190 or B2193 as well. Please assure the customer this concern will not cause a walk home. At this time engineering is aware of the concern and working towards a resolution.

RAM · 2014-12-20

Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel.Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From P0201 - P0206 - Fuel Injector X Circuit/Open. P049D - EGR Control Position Exceeding Learning Limit. P0711 - Transmission Temperature Sensor Performance. P0712 - Transmission Temperature Sensor Low. P0713 - Transmission Temperature Sensor High. P0714 - Transmission Temperature Sensor Intermittent. P0740 - TCC Out Of Range. P0869 - Line Pressure High. P0933 -…

RAM · 2014-12-20

Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel.Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201- P0206 - Fuel Injector X Circuit/Open P049D- EGR Control Position Exceeding Learning Limit P0711- Transmission Temperature Sensor Performance P0712- Transmission Temperature Sensor Low P0713- Transmission Temperature Sensor High P0714- Transmission Temperature Sensor Intermittent P0740- TCC Out Of Range P0869- Line…

RAM · 2014-11-14

Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTCs). These Faults Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: ? P0201 - P0206 - Fuel Injector X Circuit/Open. ? P049D - EGR Control Position Exceeding Learning Limit. ? P0711 - Transmission Temperature Sensor Performance. ? P0712 - Transmission Temperature Sensor Low. ? P0713 - Transmission Temperature Sensor High. ? P0714 - Transmission Temperature Sensor Intermittent. ?…

RAM · 2014-11-14

Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTCs). These Faults Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: * P0201 - P0206 - Fuel Injector X Circuit/Open. * P049D - EGR Control Position Exceeding Learning Limit. * P0711 - Transmission Temperature Sensor Performance. * P0712 - Transmission Temperature Sensor Low. * P0713 - Transmission Temperature Sensor High. * P0714 - Transmission Temperature Sensor Intermittent. *…

CADILLAC · 2014-05-07

This Preliminary Information communication provides information to the technician about vehicle that may have the following Diagnostic Trouble Codes U0401, U0140, P15F6, P1E00, U0100, P0562, P1553, P0AC4, C0110, C0898, P1EFC, P257F, P150D, P150E, C0899, U1860, U0293, C0196, P069E, U2608, U0101, U186B, P1ADE, P1AE0, P1E19, U0073, P1EDD, U0417, U184D, U1858, and C12E0 set as Passed /Failed. Technician will need to contact General Motors Technical Assistance Center for further assistance.

RAM · 2014-04-12

Flash: Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Transmission Faults. These Faults Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: ? P0201 - P0206 - FUEL INJECTOR X CIRCUIT/OPEN ? P049D - EGR CONTROL POSITION EXCEEDED LEARNING LIMIT ? P0711 - TRANSMISSION TEMPERATURE SENSOR PERFORMANCE ? P0712 - TRANSMISSION TEMPERATURE SENSOR LOW ? P0713 - TRANSMISSION TEMPERATURE SENSOR HIGH ? P0714 - TRANSMISSION TEMPERATURE SENSOR INTERMITTENT ? P0740 - TCC OUT OF RANGE ?…

AUDI · 2014-03-31

Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635,…

RAM · 2013-06-29

Flash: Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Transmission Faults. These Faults Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: ? P0711 - TRANSMISSION TEMPERATURE SENSOR PERFORMANCE ? P0712 - TRANSMISSION TEMPERATURE SENSOR LOW ? P0713 - TRANSMISSION TEMPERATURE SENSOR HIGH ? P0714 - TRANSMISSION TEMPERATURE SENSOR INTERMITTENT ? P0740 - TCC OUT OF RANGE ? P0869 - LINE PRESSURE HIGH ? P0933 - HYDRAULIC PRESSURE SENSOR RANGE/PERFORMANCE ? P0934 - LINE…

NISSAN · 2013-04-23

SERVICE INFORMATION When in "Extended Storage Mode" the applied vehicles can set DTCs U0100 and P1705, if the ignition switch is left in the accessory position for longer than 2 seconds. NOTE: These DTCs can reoccur every time the above conditions are met. These DTCs can occur due to the "Extended Storage Switch" (ESS), in the interior fuse panel, being pulled out (Storage Mode active) and those related systems being temporarily without power. If these DTCs occur due to the above condition, it does not indicate that there is anything wrong with the vehicle. See this bulletin for further detail.