U2101 · 제조사 기술 자료

LINCOLN · 2025-11-07

Some 2025 Aviator vehicles equipped with 28 radio speakers (minor feature code IDBBN) may have previously exhibited at least one of the following error messages in Ford Diagnosis and Repair System (FDRS) while programming the audio digital signal processing module (DSP):<br /><br /> * "Procedure Unsuccessful - ReadDTCs DTCs present: U2101 (Control Module Configuration Incompatible)"<br /> * "Procedure Unsuccessful - ReadDTCs DTCs present: U2100 (Initial Configuration Not Complete)"<br /> * "Procedure Unsuccessful - FlashSoftware Failed to flash RC5T-14C656-BH"<br /> * "ValidateFlashActionDIDsAgainstModule Update was not successful! FAIL - F10A = >>> SHOULD = RC5T-14C656-BH"<br /><br /> For any programming concerns not listed above, continue diagnosis outside this article. Refer to…

FORD · 2025-07-15

Some 2023-2025 F-Super Duty vehicles may display an error during replacement of the SCCM that contains the following message: "Reprogramming has failed, would you like to retry?". If this error is present, the SCCM will not complete PMI and may store diagnostic trouble codes (DTC) U2100 and/or U2101 in the SCCM. This may be due to a concern with the compatibility of the software with a hardware change in the SCCM. To correct the condition, download and run the "SCCM - Steering Column Control Module (SCCM) Configuration" application in the Ford Diagnosis and Repair System (FDRS). Inform customers that although the PMI is incomplete, there is no affect on vehicle performance. Customers can continue to drive the vehicle. To make sure the vehicle correctly receives the latest SCCM software,…

FORD · 2024-05-28

Some 2023 F-150 vehicles equipped with a 3.5L PowerBoost engine may exhibit an illuminated stability-traction control indicator with diagnostic trouble codes (DTCs) U2017:57 and U2101:00 in the ABS module. This may occur immediately after a coordinated module software update to the PCM using the Ford Diagnosis and Repair System (FDRS) scan tool. This may be due to the software level of the ABS module. To correct this condition, perform the Service Procedure below to reprogram the ABS module to the latest software level via the FDRS.

FORD · 2024-03-13

Some 2023 Bronco vehicles may exhibit diagnostic trouble code (DTC) U2101 stored in accessory protocol interface module (APIM) and/or telematics control unit (TCU) after TCU module programming with no additional symptoms present. This may be due to the TCU configuration. To correct the concern, download and run the TCU-Telematics Control Unit (TCU) Module Configuration application using Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14F546 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

FORD · 2023-06-01

Some 2023 F-Super Duty vehicles equipped with SYNC 4 may experience programming errors after a replacement of the body control module (BCM) for various concerns. After programmable module installation (PMI) of the new BCM, diagnostic trouble codes (DTC) U2100:00, U2101:00 and/or U211B:87 may be present. Download and run the Ford Diagnosis and Repair System (FDRS) application titled Trusted Real-Time Operation Network (TRON) Module Authentication, and perform the TRON Diagnosis and Repair and Reset ECU on CAN BUS routines. Once both TRON routines have been completed, re-run the BCM PMI application. Verify that all BCM DTCs have cleared. Service procedures are being updated to improve this process. Monitor OASIS for updates.

FORD · 2023-05-26

Some 2023 F-Super Duty vehicles equipped with SYNC 4 may require a replacement of the body control module (BCM) for various concerns. After programmable module installation (PMI) of the new BCM, diagnostic trouble codes (DTC) U2100:00, U2101:00 and/or U211B:87 may be present. Download and run the Ford Diagnosis and Repair System (FDRS) application titled Trusted Real-Time Operation Network (TRON) Module Authentication, and perform the TRON Diagnosis and Repair and Reset ECU on CAN BUS routines. Once both TRON routines have been completed, re-run the BCM PMI application. Verify that all BCM DTCs have cleared. Service procedures are being updated to improve this process. Monitor OASIS for updates.

FORD, LINCOLN · 2021-03-25

For 2018-2021 EcoSport/Expedition/Navigator, 2019-2021 Ranger/Transit Connect, 2020-2021 Escape/Explorer/SuperDuty/Transit/Aviator/Corsair, 2021 Bronco Sport/F-150/Mustang/Mach-E the Workshop Manual (WSM) diagnostics may direct to replace a module on vehicles that use Ford Diagnosis and Repair System (FDRS). First, an FDRS session must be created on the vehicle prior to removing the faulted module. Once the session is started, run the Programmable Module Installation and replace the module only when instructed by FDRS. Installing a new module prior to starting a scan tool session may result in incomplete module configuration with DTCs U2100, U2101 and/or U2200. Once a session has been started, continue to follow normal WSM procedures to repair the vehicle.

FORD · 2020-08-26

Some 2011-2019 Fiesta vehicles may exhibit various concerns following IPC replacement. Symptoms may include: no crank, 'Contact Hotline message', odometer displaying incorrect English or Metric units and/or diagnostic trouble code (DTC) U2101 in multiple modules. If programmable module installation (PMI) has been performed on the replacement IPC, disconnect the IPC, start a new session using the appropriate Ford scan tool and perform a PMI on the IPC. Do not reconnect the IPC until after the scan tool states it is unable to communicate with the IPC, then allow the PMI process to complete. This will automatically load the correct configuration and address any related DTCs or symptoms.

FORD · 2018-07-12

Some 2011-2018 Fiesta vehicles may exhibit various concerns following IPC replacement. Symptoms may include: no crank, Contact Hotline message, odometer displaying incorrect English or Metric units and/or diagnostic trouble code (DTC) U2101 in multiple modules. If programmable module installation (PMI) has been performed on the replacement IPC, disconnect the IPC, start a new session using the appropriate Ford scan tool and perform a PMI on the IPC. Do not reconnect the IPC until after the scan tool states it is unable to communicate with the IPC, then allow the PMI process to complete. This will automatically load the correct configuration and address any related DTCs or symptoms.

LINCOLN · 2018-03-15

Some 2016 MKC, MKX and MKZ vehicles built on or before 11/28/2015 and equipped with a TCU may exhibit an intermittent battery draw that can be isolated to the TCU, an inoperative MyLincoln Mobile app, a MyLincoln Mobile app deep sleep message, an inaccurate MyLincoln Mobile app oil life message, an incorrect MyLincoln Mobile app fuel level, a MyLincoln Mobile app false low tire warning and/or Diagnostic Trouble Codes U2100 and/or U2101 stored in the TCU. To correct the condition, program the TCU to the latest calibration using IDS version 108.06 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest calibration. For warranty claiming, use causal part 14G229 and applicable labor operations in the SLTS Manual, Section 10.

FORD · 2018-02-14

2011 Fiesta vehicles may display a DTC of U2101 after replacing an RFA module. The DTC U2101 will not cause any vehicle symptoms and can be disregarded. The RFA is not programmable and does not require programmable module installation, as-built configuration or module reprogramming when replaced.

FORD · 2018-01-10

Some 2011-2017 Fiesta vehicles may exhibit various concerns following IPC replacement including odometer displaying incorrect English or Metric units and/or diagnostic trouble code (DTC) U2101 in multiple modules. If Programmable Module Installation (PMI) has been performed on the replacement IPC, disconnect the IPC, start a new Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) session and perform a PMI on the IPC. Do not reconnect the IPC until after the IDS or FJDS states it is unable to communicate with the IPC, then allow the PMI process to complete. This will automatically load the correct configuration and address any related DTCs or symptoms.

FORD, LINCOLN · 2017-11-03

Some 2017-2018 Fusion/MKZ vehicles built on or before 27-Oct-2017 may exhibit an illuminated airbag lamp and/or SYNC 911 assist not operational message being displayed. Connect the IDS and check the RCM and APIM for DTCs. If any of the following RCM DTCs U3000, U2100, U2101, U2300, U0455, B0080, B141B, B141C, B0054, B140C, B140D, B0057, B140E, B140F and/or APIM DTC U0452 is stored, then reprogram the RCM to the latest level using IDS or FJDS 107.04 or higher. After reprograming, perform an as-built configuration of the RCM. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 14B321 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual. Calibration files may also…

FORD, LINCOLN · 2016-10-05

SOME 2017 FUSION/MKZ VEHICLES BUILT ON OR BEFORE 18-AUG-2016 MAY EXHIBIT AN AIR BAG LAMP. CONNECT THE IDS AND CHECK THE RCM FOR DTCS. IF DTC U3000, U2100, U2101, U2300, U0455, U0452, B0080, B141B, B141C, B0054, B140C, B140D, B0057, B140E, AND/OR B140F ARE STORED IN THE RCM, REPROGRAM THE RCM TO THE LATEST LEVEL USING IDS RELEASE 102.03 OR HIGHER. AFTER REPROGRAMING, PERFORM AN AS-BUILT CONFIGURATION OF THE RCM. SELECT NO WHEN ASKED IF YOU WERE SENT HERE BY AN ARTICLE. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. USE THE APPLICABLE LABOR OPERATION IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS MANUAL AND CAUSAL PART 14B321 WHEN CLAIMING THIS REPAIR. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM

LINCOLN · 2015-08-01

2016 MKZ,MKC AND MKX: MY LINCOLN MOBILE APP NOT ABLE TO CONNECT TO VEHICLES EQUIPPED WITH DTC U2100 AND/OR U2101 ON VEHICLES WITH TELEMATICS CONTROL UNIT *CN

FORD · 2014-05-01

FORD: AFTER PERFORMING REPAIRS OR DIAGNOSING TO ANY VEHICLE SYSTEMS, THE FRONT CONTROL DISPLAY INTERFACE MODULE (FCDIM) WILL EXHIBIT DTC U2101 AND CAN BE RESOLVED BY REPROGRAMMING THE FCDIM TO LATEST CALIBRATION. MODEL 2014 FIESTA. *PE