목록의 차량은 조사 단서입니다. 제조사 자료에서 엔진, 생산 기간, 소프트웨어 조건을 확인하세요.
U3000 ← 이 코드는 무엇을 뜻하나요?217 결과
MAZDA · 2023-01-03
Some vehicles may exhibit DTC U3000:04 (Telematics communication unit internal malfunction) stored after the connected service contract has been discontinued (only vehicles in which the customer opted out of CV services are affected - CSP04). This is caused by improper control software of telematics communication unit. To eliminate this concern, the control software of telematics communication unit has been modified.
FORD · 2022-12-20
This article supersedes TSB 22-2402 to update the vehicle model years affected. Some 2021-2022 Mustang Mach-E base model (non-GT) built on or before 25-Jul-2022, 2022-2023 e-Transit vehicles built on or before 17-Sep-2022 may experience an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P1A3C, U3000:16, U3000:64, U3000:04 and/or U3000:45 in the off-board charging controller (OBCC) module and the high voltage (HV) battery will not charge using a level 3 direct current (DC) fast charging station/electrical vehicle supply equipment (EVSE). This may be due to OBCC software. To correct the condition, follow the Service Procedure to reprogram the OBCC.
FORD, LINCOLN · 2022-12-14
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, and 2022 Maverick vehicles may exhibit a hard, stiff, and/or difficult to turn condition due to a lack of power steering assist during engine start-up with various U3000 diagnostic trouble codes (DTCs) and/or U3000:66. To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) tool, select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. After PSCM reset, perform an ignition cycle. Update the PSCM to the latest software level using (FDRS) tool. If DTCs U3000 returns, continue with diagnostics and repair direction using Workshop Manual (WSM), Section 211-02 > Power Steering > Diagnosis and Testing. For claiming, use causal part 3C529 and applicable labor operations in…
CADILLAC · 2022-12-07
This Preliminary information communicates to dealer that a false code U3000 may set in the radio and should be ignored until software is released to correct the false code.
BUICK · 2022-12-02
This technical bulletin provides repair information to correct a customer concern of Service Cluster Message and DTC U3000 Set.
FORD · 2022-12-01
Some 2021-2023 F-150 vehicles may experience a lack of steering assist upon start-up along with a Steering Assist Fault message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTC) U3001:89 and U3000:96 in the power steering control module (PSCM). This may be due to low voltage at the PSCM. Power steering assist will be restored when sufficient voltage is supplied. To clear the DTCs using the Ford Diagnosis and Repair System (FDRS), select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. Once cleared, cycle the ignition to verify normal system operation. If the DTCs return, refer to Workshop Manual Section 211-02 for normal diagnostics. For claiming, use causal part 3504.
BUICK · 2022-11-23
This technical bulletin provides repair information to correct a customer concern of Service Cluster Message and DTC U3000 Set.
MAZDA · 2022-11-16
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA04_12004 or later). Ver. 7000C0A-NA04_12004 and later fixes these software errors (bugs): * Album artwork may not appear when playing music using an USB connected iPhone. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into R position. * The screen freezes and goes to a white screen, then the system reboots. * The steering wheel switches and commander switches cannot control the audio system. * DTC U3000:49 is stored which may be accompanied with following symptoms: - No sound emitting from the speakers. - Audio source selection is unavailable. * The vehicle icon rotates when using the…
MAZDA · 2022-11-01
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA01_12004 or later). Ver. 7000C0A-NA01_12004 fixes these software errors (bugs): * Album artwork may not appear when playing music using an USB connected iPhone. * The center display may turn black when the gear is shifted from reverse position to parking position. * Screen freezes and goes to white screen, then the system reboots. * Steering wheel switches and commander switches cannot control the audio system. * DTC U3000:49 is stored which may be accompanied with following symptoms. - No sound comes out from the speakers. - Audio source selection is unavailable. * When using the navigation with head-up mode, the vehicle icon rotates. * Beep sounds every after…
FORD · 2022-10-25
Some 2021-2022 Mustang Mach-E base model (non-GT) built on or before 25-Jul-2022, 2022 e-Transit vehicles built on or before 17-Sep-2022 may experience an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P1A3C, U3000:16, U3000:64, U3000:04 and/or U3000:45 in the off-board charging controller (OBCC) module and the high voltage (HV) battery will not charge using a level 3 direct current (DC) fast charging station/electrical vehicle supply equipment (EVSE). This may be due to OBCC software. To correct the condition, follow the Service Procedure to reprogram the OBCC.
FORD, LINCOLN · 2022-10-20
Some 2021-2022 Mustang Mach-E/Escape plug-in hybrid electric vehicle (PHEV), 2020-2022 Aviator PHEV, and 2022 Transit battery electric vehicle (BEV) vehicles may experience an illuminated powertrain malfunction (Wrench) indicator and/or malfunction indicator lamp (MIL) with secondary on board diagnostic control module (SOBDM) diagnostic trouble code (DTC) U3000:49. This may be due to an internal SOBDM concern. To correct the concern, replace the SOBDM following Workshop Manual, Section 414-03B Removal and Installation, Secondary On-board Diagnostic Control Module. For claiming use base part # 10B689 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
FORD · 2022-10-19
Some 2022 F-150 Lightning vehicles equipped with Phone-as-a-Key may exhibit a U3000:49 diagnostic trouble code (DTC) stored in the remote function actuator (RFA) module. This may be due to RFA module software. To correct this condition, reprogram the RFA module using the latest software level of the Ford Diagnosis and Repair System (FDRS). If no update is available, continue with the normal Workshop Manual (WSM) diagnostics. For claiming, use causal part 14G617 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
MAZDA · 2022-10-11
If the right-side Blind Spot Monitoring (BSM) control module is replaced for any reason, it is also necessary to replace the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. Other possible symptoms that may be found if the right-side BSM module is replaced alone: * BSM aiming fails * "BSM OFF" indicator ON * Center Display warning message * BSM failsafe (No operation) * DTC U3000:54 stored in memory * DTC U1A4B:54 stored in memory (CX-3, MX-5 only)
BUICK · 2022-08-10
This technical bulletin provides repair information to correct a customer concern of Service Power Steering Message with DTC U3000 Set.
FORD, LINCOLN · 2022-07-22
Some 2021-2022 F-150, Mustang Mach-E and 2022 Expedition/Navigator vehicles may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble codes (DTC) U3000:49, U3000:89, U2107:68, C1001:54 and/or C1001:78. DTC B1578:78 may also set after an image processing module A (IPMA) on-demand self test is performed. This may be due to software in the IPMA. To correct the condition, follow the Service Procedure to reprogram the IPMA to the latest level.
FORD · 2022-07-20
Some 2021-2022 F-150 vehicles equipped with On-Board Scale may exhibit DTC U3000:54 stored in the VDM after replacement and will not clear. A warning message may also be displayed in the center display screen. If programmable module installation (PMI) was not followed or the original VDM will not communicate, the U3000:54 may be stored. If the original VDM communicates, perform a PMI before VDM removal. This DTC does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution that is expected in September 2022. Replacement or reprogramming of the VDM will not resolve this condition. Monitor OASIS for additional information…
FORD · 2022-07-04
Some 2021-2022 Mustang Mach-E, 2022 Transit battery electric vehicles (BEV) may experience an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P1A3C, U3000:16, U3000:64, U3000:04 and/or U3000:45 in the off board charging controller (OBCC) module and the high voltage (HV) battery will not charge using a level 3 direct current (DC) fast charging station/electrical vehicle supply equipment (EVSE). This may be due to OBCC software. To correct the condition, follow the Service Procedure to reprogram the OBCC.
CHEVROLET, GMC · 2022-06-24
This technical bulletin provides repair information to correct a customer concern of a “Service Instrument Cluster” Lamp Illuminated on the DIC with DTC U3000 Set.
CHEVROLET, GMC · 2022-06-07
This Preliminary information communicates an issue with the front view camera setting a DTC U3000 and disabling. Engineering is working on a fix.
CHEVROLET, GMC · 2022-05-20
This Preliminary information communicates an issue with the front view camera setting a DTC U3000 and disabling. Engineering is working on a fix.
CHEVROLET, GMC · 2022-05-18
This Preliminary information communicates an issue with the front view camera setting a DTC U3000 and disabling. Engineering is working on a fix.
CHEVROLET, GMC · 2022-05-05
This Preliminary information communicates an issue with the front view camera setting a DTC U3000 and disabling. Engineering is working on a fix.
FORD · 2022-03-23
This article supersedes TSB 22-2069 to update the Service Procedure. Some 2021 F-150 and Mustang Mach-E vehicles may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble codes (DTC) U3000:49, U3000:89, U2107:68, C1001:54 and/or C1001:78. DTC B1578:78 may also set after an image processing module A (IPMA) on-demand self test is performed. This may be due to software in the IPMA. To correct the condition, follow the Service Procedure to reprogram the IPMA to the latest level.
CADILLAC, CHEVROLET, GMC · 2022-03-22
This technical bulletin provides repair information to correct a customer concern of Short Range Radar (SRR) with DTC U3000 49 Set.
FORD · 2022-03-01
Some 2021 F-150 vehicles built on or before 22-Jul-2021 at Dearborn Truck Plant, 2021 F-150 vehicles built on or before 08-Oct-2021 at Kansas City Assembly Plant and Mustang Mach-E vehicles built on or before 07-Jul-2021 may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble codes (DTC) U3000:49, U3000:89, U2107:68, C1001:54 and/or C1001:78. This may be due to software in the image processing module A (IPMA). The revised IPMA calibration is currently not available.
FORD · 2022-02-24
Some 2021 Mustang Mach-E vehicles may experience an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P1A3C, U3000:16, U3000:64, U3000:04 and/or U3000:45 in the off board charging controller (OBCC) module and the high voltage (HV) battery will not charge using a level 3 DC fast charging station/electrical vehicle supply equipment (EVSE). This may be due to OBCC software. To correct the condition, follow the Service Procedure to reprogram the OBCC.
FORD · 2022-02-10
Some 2021 F-150 vehicles built on or before 17-Mar-2021 may experience a lack of steering assist upon start-up along with a Steering Assist Fault message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTC) U3000:96 and U3001:68 in the power steering control module (PSCM). This may be due to battery voltage below 8 volts when attempting to start the vehicle. Power steering assist will be restored when battery voltage is at or above 12 volts and the DTCs are cleared. Replacement of the PSCM is not necessary. To clear the DTCs using the FDRS, select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. Once cleared, cycle the ignition to verify normal system operation. If the DTCs return, refer to Workshop Manual Section 211-02 for normal…
HONDA · 2022-01-29
ServiceNews Article - There are several possible causes for the SRS DTC U3000-49 (Internal Failure of the SRS Unit) to be stored. If you can duplicate the DTC, the troubleshooting will take you through the step-by-step process in isolating the faulty component. In most situations, the SRS Unit should be last on the list of components to replace. Here is a quick tip for troubleshooting a faulty seat weight sensor.
MAZDA · 2022-01-27
Some vehicle may experience the i-ACTIVSENSE/ALH warning lights on and a system error messages may be found in the center display as well. DTC U3000:04 (FSC) is stored in memory DTC U3000:04 (FSC) - Forward sensing camera (FSC) internal malfunction This may be caused by a hardware failure in an internal device of the FSC that results in the malfunction detection. To eliminate this concern, the production process of the FSC has been modified.
FORD, LINCOLN · 2022-01-14
Some 2019-2020 Edge/Nautilus vehicles built on or before 03-Dec-2020 may exhibit a power liftgate unable to unlatch from both switches after a second unlatch attempt with or without diagnostic trouble code (DTC) U3000:49 stored in the rear gate trunk module (RGTM). If the RGTM is at the latest software level and the condition is still present, refer to the Workshop Manual (WSM) Section 501-03 to perform normal diagnosis.