U0415 · Comunicados do fabricante

FORD · 2026-05-06

Some 2025-2026 Bronco vehicles may exhibit various cruise control, pre-collision and/or front stabilizer bar disconnect related warning messages displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0418:86 stored in the image processing module A (IPMA). DTC U0415:00 may also be stored in the CHCM. <br /><br /> If wheel speed sensor specific DTCs are present in the anti-lock brake (ABS) module and/or warning messages other than those listed above are present, this SSM does not apply. Refer to the Workshop Manual (WSM) for normal diagnostics. <br /><br /> If a vehicle exhibits this condition, carefully inspect the rear wheel speed sensors for correct installation with the rear wheel speed sensor body seated flush against the axle housing. Repair or replace the…

FORD · 2026-04-24

Some 2025-2026 Bronco vehicles may exhibit various cruise control, pre-collision and/or front stabilizer bar disconnect related warning messages displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0418:86 stored in the image processing module A (IPMA) and no wheel speed sensor specific DTCs present in the anti-lock brake (ABS) module. DTC U0415:00 may also be stored in the CHCM. If a vehicle exhibits this condition, carefully inspect the rear wheel speed sensors for correct installation with the rear wheel speed sensor body seated flush against the axle housing. Repair or replace the affected rear wheel speed sensor as needed, clear the DTC, and retest. Refer to Workshop Manual (WSM), Section 206-09. If the condition persists, advise the customer that…

MAZDA · 2026-02-26

Some vehicles may display some (or all) of the following symptoms: • Check engine light on with DTC P061B • Light increase in engine rpms during acceleration • Transmission will not shift past 4th gear • Various U codes (U0401 ABS, U0401, U0415 FSC, U0301, U0316 SBS/MRCC, U0442 TCM) may be set

MAZDA · 2025-12-05

A technician may report that DTC U0415:68 - VCM (Vehicle Control Module) cannot be cleared after replacing the DSC (Dynamic Stability Control) module.

FORD · 2025-12-03

Some 2023-2026 F-Super Duty vehicles built on or before 01-Oct-2025 may exhibit a "Hill Start Assist Unavailable" and/or "Parking Brake Limited Function" message at vehicle start-up with diagnostic trouble codes (DTCs) U0151, U023A, U0159 and/or U0146 stored in the anti-lock brake system (ABS) module. These DTCs and/or U0415 may also be present in various other modules related to "invalid data received from the ABS control module". This may be due to the software in the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 2C219 and labor operations 2219D and 2219D44.

JEEP · 2025-10-25

Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● U0415-00 - Invalid Data Received From Anti-lock Brake System (ABS) Control Module “A”. Customers may also experience the following: ● "Service Transmission" message is displayed on the Instrument Panel Cluster (IPC) This bulletin involves reprogramming the TCM with the latest available software.

JEEP · 2025-09-27

Not applicable to vehicles built for US market. Multiple Systems Repair Bundle Campaign Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U11E3-00 - TCM Lost Communication With ESM On DPT CAN. ● B15A1-00 - Media Port 1 Connection. ● U11C2 - Lost Transmission Message. ● U11E4-00 - CAN Communication Messages Missing. ● U120C - Lost Brake Booster Signal. ● U1216-00 - Lost Communication With DASM. ● U121E-00 - Lost Communication With Steering Wheel Cruise Control Switch. ● U1267-00 - No Valid Data From ESM On CAN-C Or CAN-DPT. ● U12A8 - Lost Communication With Master Cylinder Pressure Sensor. ● U1465-00 - Implausible Driver Shift Request Signal Received. ● U1466-00-…

FORD · 2025-08-26

This article supersedes TSB 22-2214 to update labor times from M-time to AP-time and add a limit. Some of the vehicles listed in the model statement above may exhibit at least one of the following conditions: - "Reverse Brake Assist Unavailable" message displayed in the instrument panel cluster (IPC) with missing active guide lines in the reverse camera display - Diagnostic trouble code (DTC) U0415:86 stored in the IPMA This may be due to a software issue with the anti-lock brake system (ABS) module.

FORD · 2025-08-22

Some 2023-2025 F-Super Duty vehicles may exhibit a "Hill Start Assist Unavailable" and/or "Parking Brake Limited Function" message at vehicle start-up with diagnostic trouble codes (DTCs) U0151, U023A, U0159, and/or U0146 stored in the anti-lock brake system (ABS) module. These DTCs and/or U0415 may also be present in various other modules related to "invalid data received from the ABS control module". This may be due to the software in the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 2C219 and labor operation 2219D and 2219D44.

JEEP · 2025-08-05

Symptoms/Condition: Shifter reports loss communication AND NO OTHER MODULES report the condition. Diagnostic: Please make sure ONLY shifter reports loss communication. If there are other modules reporting loss communication, then follow the existing service procedure Repair Procedure: 1. Verify Complaint - ESM reports a Loss of Communication (LOC) DTC, but no other modules do. - If multiple modules report the same LOC, the ESM is not the cause (its not a gateway module). 2. Read DTCs - Relevant codes: U0101, U0140, U0155, U0129, U11C3, U0402, U0422, U0423, U0415, U145D. - If multiple LOC DTCs are present: a. Check battery health, system voltage, and TCM (including valve body). b. If TCM goes offline, ESM may falsely report LOC DTCs. 3. Check Environmental Data - Look for voltage/system…

FORD · 2025-06-11

Some 2023-2025 F-Super Duty vehicles may exhibit a "Hill Start Assist Unavailable" and/or "Parking Brake Limited Function" message at vehicle start-up with diagnostic trouble codes (DTC) U0151, U023A, U0159, and/or U0146 stored in the anti-lock brake system (ABS) module. These DTCs and/or U0415 may also be present in various other modules related to "invalid data received from the ABS control module". Replacement or reprogramming of the ABS module will not resolve this condition. There is no effect to the parking brake or other vehicle functions. This does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this…

LINCOLN · 2025-06-04

Some 2025 Navigator vehicles may set diagnostic trouble code (DTC) U0415 in the power steering control module (PSCM) when a diagnostic self-test is performed. This may be due to PSCM DTC sensitivity during vehicle key on/start-up. Replacement or reprogramming of the PSCM will not resolve this condition. U0415 should be ignored and no further service action is required if no other DTCs are present in the PSCM, no warning indicators are illuminated while the engine is running, and no symptoms present.

FORD · 2024-07-19

Some 2022-2024 Ford Edge ST vehicles equipped with all wheel drive (AWD), a 2.7L engine, and ACC may exhibit cruise control deactivating with an illuminated anti-lock brake system (ABS) warning light flashing and various brake and driver-assist warning indicators. Diagnostic trouble codes (DTCs) U3000:49 may be stored in the ABS module with U0415 in the power steering control module (PSCM). This may be due to the software in the ABS module.

LINCOLN · 2023-12-08

Some 2024 Nautilus vehicles may set diagnostic trouble code (DTC) U0415:29 in the power steering control module (PSCM) when a diagnostic self-test is performed. This may be due to PSCM DTC sensitivity during vehicle key on/start-up. Replacement or reprogramming of the PSCM will not resolve this condition. U0415:29 should be ignored and no further service action is required if no other DTCs are present in the PSCM, no warning indicators are illuminated while the engine is running, and no symptoms present.

FORD · 2023-03-24

Some 2023 F-Super Duty vehicles may set diagnostic trouble code (DTC) U0415 in the all-wheel drive (AWD) module during a diagnostic self-test. This DTC sets when the AWD module does not detect a valid signal from the anti-lock brake (ABS) module through the controller area network (CAN) within a specified time frame. U0415 should be ignored if: no other DTCs are present in the ABS module or AWD module, the malfunction indicator lamp (MIL) is not illuminated while the engine is running, and no drivability concerns are present. No further service action is required.

FORD, LINCOLN · 2023-03-14

Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles built on or before 23-Mar-2022 may exhibit driver assistance warning messages displayed in the instrument panel cluster (IPC): Pre-collision Assist Not Available, Cruise Control Not Available, Collision Warning Malfunction and/or Adaptive Cruise Control Malfunction. Diagnostic trouble code (DTC) U0415:00 may also be stored in the power steering control module (PSCM), DTC C0051:67 stored in the anti-lock brake system (ABS) module and DTC U0418:86 stored in the image processing module A (IPMA). This may be due to the software in the PSCM. Using the latest version of Ford Diagnosis and Repair System (FDRS) scan tool, update the PSCM to the latest software level. For claiming, use causal part 3C529 and applicable…

FORD, LINCOLN · 2023-01-06

Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles may exhibit any of the following driver assistance warning messages displayed in the instrument panel cluster (IPC): Pre-collision Assist Not Available, Cruise Control Not Available, Collision Warning Malfunction and/or Adaptive Cruise Control Malfunction. Diagnostic trouble code (DTC) U0415:00 may also be stored in the power steering control module (PSCM), DTC C0051:67 stored in the anti-lock brake system (ABS) module and DTC U0418:86 stored in the image processing module A (IPMA). This may be due to the software in the power steering control module (PSCM). To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) scan tool. Update the PSCM to the latest software level.

FORD · 2022-11-18

Some 2021-2022 Bronco vehicles equipped with a 2.7/3.0L engine may experience a loss of the go over any terrain (GOAT) mode and/or differential locking function when two diagonal wheels lose traction simultaneously while the other two wheels maintain traction. Diagnostic trouble code (DTC) U0415 may be set in several modules. The issue should correct itself after the vehicle is driven on flat ground and over 28 MPH for a few minutes. This may be due to the software within the anti-lock brake system module (ABS). To correct this condition, reprogram the ABS module using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use casual part 2C219.

LINCOLN · 2022-09-26

Some 2019 MKC vehicles without lane keep assist may exhibit an AdvanceTrac/hill start assist message(s) and/or illuminated electronic stability control/traction control indicator lamp with diagnostic trouble codes (DTCs) U0420 stored in the anti-lock brake (ABS) module and U0415 stored in the power steering control module (PSCM). This concern may also result in additional DTCs. DTCs U0420 and U0415 may have been set as a result of low system voltage during a vehicle start. The PSCM may have a communication fault with the ABS module when it reacts to low voltage when the key is on. To correct the condition, replace the ABS control module using the service part number KJ7Z-2C219-C. For claiming, use causal part 2C219 and applicable labor operations in Section 02 of the Service Labor Time…

FORD · 2022-06-01

Some 2021 Mustang Mach-E/F-150 vehicles may exhibit a Reverse Brake Assist Unavailable message displayed in the instrument panel cluster (IPC) with missing active guide lines in the reverse camera display and/or diagnostic trouble code (DTC) U0415:86 stored in the IPMA. This may be due to a software issue with the anti-lock brake system (ABS) module. To correct the condition, follow the Service Procedure to reprogram the ABS module.

FORD, LINCOLN · 2022-05-11

Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles may exhibit any of the following driver assistance warning messages displayed in the instrument panel cluster (IPC): Pre-collision Assist Not Available, Cruise Control Not Available, Collision Warning Malfunction and/or Adaptive Cruise Control Malfunction. Diagnostic trouble code (DTC) U0415:00 may also be stored in the power steering control module (PSCM), DTC C0051:67 stored in the anti-lock brake system (ABS) module and DTC U0418:86 stored in the image processing module A (IPMA). This may be due to the software in the power steering control module (PSCM). To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) scan tool. Update the PSCM to the latest software level.

FORD · 2021-11-10

Some 2021 Mustang Mach-E/F-150 vehicles may exhibit a Reverse Brake Assist Unavailable message displayed in the instrument panel cluster (IPC) with missing active guide lines in the reverse camera display. Diagnostic trouble code (DTC) U0415:86 may also be present in the IPMA. This may be due to a network interruption during module programming and/or when a module was disconnected which can cause the steering center find to be reset and various features to become disabled. The steering center find can be relearned by driving the vehicle for approximately 5 minutes, above 18 mph (30 km/h) and with no steering wheel input for a few seconds. When steering center is found, the Reverse Brake Assist Unavailable message should clear. If the active guide lines are missing, perform the IPMA camera…

MAZDA · 2021-07-13

When switching to the maintenance mode, U3000:53 and the related DTCs are stored, but the DTCs will not be cleared automatically after finishing the maintenance mode. It is necessary to clear the DTCs completely after performing the brake system maintenance mode. DTC codes: U3000:53, C0021:52, U0415:68

RAM · 2021-03-16

Flash: Hybrid Control Processor (HCP) Updates This bulletin involves updating the HCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). P1A26-00 - BPCM Hybrid Battery State Of Charge Performance. P0A7E-00 - Hybrid/EV Battery Pack Over Temperature. U1003-00 - ESP Can C Bus Performance. P2534-00 - Ignition Switch Run/Start Position Circuit Low. P0506 - Idle Speed Performance Lower Than Expected. P0507 - Idle Speed Performance Higher Than Expected. One Trip DTC Changed to a Two Trip DTC.P0AC6-00 - Hybrid/Ev Battery Temperature Sensor 2 Circuit Performance. P0ACB-00 - Hybrid/Ev Battery Temperature Sensor 3 Circuit…

RAM · 2021-03-16

Flash: Hybrid Control Processor (HCP) Updates This bulletin involves updating the HCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). P1A26-00 - BPCM Hybrid Battery State Of Charge Performance. P0A7E-00 - Hybrid/EV Battery Pack Over Temperature. U1003-00 - ESP Can C Bus Performance. P2534-00 - Ignition Switch Run/Start Position Circuit Low. P0506 - Idle Speed Performance Lower Than Expected. P0507 - Idle Speed Performance Higher Than Expected. One Trip DTC Changed to a Two Trip DTC.P0AC6-00 - Hybrid/Ev Battery Temperature Sensor 2 Circuit Performance. P0ACB-00 - Hybrid/Ev Battery Temperature Sensor 3 Circuit…

FORD, LINCOLN · 2021-01-12

Some 2020-2021 Explorer/Aviator vehicles built on or before 07-Dec-2020 may falsely store diagnostic trouble codes (DTCs) U0415 and/or U3000:42 in the image processing module B (IPMB). These DTCs may be associated with camera display issues or a Reverse Brake Assist Unavailable fault message. To correct the condition, reprogram the IPMB using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19H405 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

CHRYSLER · 2020-07-02

EPB And ACC Disabled Displayed In Information Center EVIC. DTC?s C2222-68 C10D0-92 and U0415-00.

CHEVROLET, GMC · 2020-05-20

This Preliminary Information communication provides information to the technician that vehicles may have an Antilock Braking System or Malfunction Indicator Lamp illuminated. Also Low Brake Fluid lamp on with the master cylinder fluid level is full or a Service Trailer Brake message on the Driver Information Center. Technician may find codes C0035, C0040, C0045, C0050, C0055, C0267, U0121, U0415 or U0420. Technician will need to inspect the Electronic Brake Control Module connector for water intrusion or corrosion on the terminals. If either is found, replace the EBCM and replace the affected terminals. Also remove the tape from the conduit leading to G400 between the main harness and the ground lug.

CHEVROLET, GMC · 2020-03-20

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Trailer Brake message in the Driver Information Center. Also the vehicle will have a Diagnostic Trouble Code U0415 set. Technician will fill the master cylinder brake fluid reservoir to the maximum level.

LINCOLN · 2020-02-04

2019 MKC - Without Lane Keep Assist AdvanceTrac, Hill Start Assist Message(s) And/Or Stability Control Indicator Lamp Illuminated With DTCs U0420 And U0415 Some 2019 MKC vehicles without lane keep assist may exhibit an advancetrac, hill start assist message(s) and/or the electronic stability control/traction control indicator lamp illuminated with diagnostic trouble codes (DTCs) U0420 stored in the anti-lock brake module (ABS) and U0415 stored in the power steering control module (PSCM). This concern may also result in additional DTCs. DTCs U0420 and U0415 may have been inadvertently set as a result of low system voltage during a vehicle start. To resolve the concern, reprogram the ABS control module using the latest software level of the appropriate Ford diagnostic scan tool. For…