P0390 · Материалы производителя

RAM · 2026-07-22

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle exhibit/set SYMPTOM: one or more of the following Diagnostic Trouble Codes (DTCs): ● P0420 - Catalyst System Efficiency Below Threshold Bank 1. ● P0430 - Catalyst System Efficiency Below Threshold Bank 2. ● P0556 - Brake Booster Pressure Sensor Circuit Performance. ● P0340 - Cam Position Sensor Circuit - Bank 1 Intake. ● P0345 - Cam Position Sensor Circuit - Bank 2 Intake. ● P0365 - Cam Position Sensor Circuit - Bank 1 Exhaust. ● P0390 - Cam Position Sensor Circuit - Bank 2 Exhaust. Customers may experience one or more of the following: ● Vehicle fails emissions inspection testing. ● Fuel odor during frequent stop and re-start driving, during high…

RAM · 2022-05-26

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set: P0556 - Brake Booster Pressure Sensor Circuit Performance. P0340 - Cam Position Sensor Circuit - Bank 1 Intake. P0345 - Cam Position Sensor Circuit - Bank 2 Intake. P0365 - Cam Position Sensor Circuit - Bank 1 Exhaust. P0390 - Cam Position Sensor Circuit - Bank 2 Exhaust. Customer may describe the following:Fuel odor during frequent stop and re-start driving, during high ambient temps. The following software enhancements are also available: OBD calibration turned off DTC U0463 - Fuel…

CHRYSLER · 2022-03-11

Flash: Powertrain Control Module (PCM) Updates This bulletin involves updating the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may notice one or moreof the following Diagnostic Trouble Codes (DTCs) have been set: P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor A. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor A. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor B. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor B.

CHRYSLER · 2022-03-11

Flash: Powertrain Control Module (PCM) Updates This bulletin involves updating the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may notice one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor A. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor A. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor B. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor B.

JEEP · 2020-10-28

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find oneor more of the following Diagnostic Trouble Codes (DTCs).P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0344 - Camshaft Position Sensor Intermittent. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 -…

JEEP · 2020-10-28

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0344 - Camshaft Position Sensor Intermittent. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 -…

DODGE, JEEP · 2020-05-27

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set:P06EF - Engine Restart Performance(3.0L and 3.6L Only). P0556 - Brake Booster Pressure Sensor Circuit Performance. P040B - Exhaust Gas Recirculation Temperature Sensor 1 Circuit Performance(3.6L Only). U1424 - Implausible Engine Torque Signal Received(2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open(3.6L Only). P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation(3.0L and 3.6L Only). The following DTCs…

RAM · 2019-11-01

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0340 - Cam Position Sensor Circuit - Bank 1 Intake. P0345 - Cam Position Sensor Circuit - Bank 2 Intake. P0365 - Cam Position Sensor Circuit - Bank 1 Exhaust. P0390 - Cam Position Sensor Circuit - Bank 2 Exhaust. The following software enhancements are also available:OBD calibration turned offDTC U0463 - Fuel Level Implausiblemessage code and will now be detected withDTC P0463 - Fuel Level Sensor 1 Circuit High. More robust trailer brake module enhancements for…

RAM · 2019-11-01

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0340 - Cam Position Sensor Circuit - Bank 1 Intake. P0345 - Cam Position Sensor Circuit - Bank 2 Intake. P0365 - Cam Position Sensor Circuit - Bank 1 Exhaust. P0390 - Cam Position Sensor Circuit - Bank 2 Exhaust. The following software enhancements are also available:OBD calibration turned offDTC U0463 - Fuel Level Implausiblemessage code and will now be detected withDTC P0463 - Fuel Level Sensor 1 Circuit High. More robust trailer brake module enhancements for…

CHRYSLER · 2019-05-04

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. A customer or technicians may be unable to read data information from the OBDII connector when using a generic scan tool (APAC).Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following DTCs have been set (NAFTA):U0418 - Implausible Data Received From Brake System Control Module 1. U0432 - Invalid Data Received From Multi-Axis Acceleration Sensor Module. P06EF - Engine Restart Performance. P06E9 - Engine Starter Performance. P00FD - Battery -B- State Of Charge Performance. C2222-68 - Improper Powerdown - Event Information. P0607-00 - ECU Internal Performance - ESM. U0402-00 -…

FORD · 2018-12-03

Some 2018 F-150 and 2018-2019 Mustang vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with DTCs P0390 and/or P0394 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.

FORD · 2018-08-02

Some 2018 F-150 vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with DTCs P0390 and/or P0394. These DTCs may be caused by low engine oil level. Before performing any diagnosis or repair, make sure the oil level is between the minimum and maximum marks on the oil level indicator. If the oil level is below the minimum mark, diagnose the low oil level concern first. Refer to the Workshop Manual, Section 303-00. If the oil level is in the normal operating range, inspect C1627. If no concerns are present, replace the bank 2 (LH) exhaust variable camshaft timing (VCT) solenoid. Do not replace camshaft position sensors for these DTCs. For claiming, use causal part 6M280 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.…

DODGE, JEEP · 2017-09-23

Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P0556 - Brake Booster Pressure Sensor Circuit Performance. P040B - Exhaust Gas Recirculation Temperature Sensor 1 Circuit Performance(3.6L Only). U1424 - Implausible Engine Torque Signal Received(2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open(3.6L Only). P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation(3.0L and 3.6L Only). The following DTCs have been changed from a one…

DODGE, JEEP · 2017-08-29

Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P040B - Exhaust Gas Recirculation Temperature Sensor 1 Circuit Performance(2017 MY with a 3.6L Only). U1424 - Implausible Engine Torque Signal Received(2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open(3.6L Only). P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation(3.0L and 3.6L Only). The following DTCs have been changed from a one trip fault to a two trip fault for(3.0L and…

CHRYSLER · 2017-08-09

Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following DiagnosticTrouble Codes (DTCs) have been set:U1400-00 - Implausible TPS Signal Received P1D73 - AGS Performance -(Active Grill Shutter). P0171 - Fuel System 1/1 Lean. P0174 - Fuel System 2/1 Lean. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to atwo trip fault:P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent…

SUBARU · 2015-08-06

"THIS SERVICE INFORMATION BULLETIN ANNOUNCES A DESIGN CHANGE TO THE ENGINE WIRING HARNESS TO PREVENT WATER INTRUSION AND ACCUMULATION FROM OCCURRING INSIDE THE CORRUGATED PLASTIC HARNESS TUBING. IN SOME CASES, THIS ACCUMULATION MAY CAUSE A CHECK ENGINE LIGHT TO ILLUMINATE AND EXHAUST CAMSHAFT POSITION-RELATED DTCS TO BE STORED IN THE ECM MEMORY (E.G. P0390, P0391). THE CHANGE INVOLVES FULL TAPING OF THE HARNESS TUBE AS OPPOSED TO PITCH TAPING (NO TAPE OVERLAP) TO ENHANCE “SEALING” OF THE HARNESS TUBE AND PREVENT WATER INTRUSION WHICH MAY OCCUR DURING ENGINE CLEANING (STEAM CLEANING AND / OR PRESSURE WASHING). UNDER NORMAL DRIVING CONDITIONS, THERE IS NO POSSIBILITY OF THIS CONDITION OCCURRING. COMPARISON PHOTOS OF THE TAPING ARE SHOWN BELOW FOR REFERENCE."

CHRYSLER, DODGE, FIAT, JEEP, RAM · 2015-08-04

Camshaft Position Sensor If replacing a camshaft position sensor for P0340, P0344, P0345, P0349, P0365, P0369, P0390 or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com

SCION · 2014-05-30

TSB: Some 2013 model year FR-S vehicles may exhibit intake and/or exhaust camshaft position sensor related and/or engine misfire DTCs (P0340, P0341, P0345, P0346, P0365, P0366, P0390, P0391, P0301, P0302, P0303, and P0304) due to the camshaft position sensor clearance being out of specification. In addition, some vehicles may also experience rough idle or extended cranking. This bulletin provides inspection and repair procedures to improve this condition.

SCION · 2014-04-16

Some 2013 model year FR-s vehicles may exhibit intake and/or exhaust camshaft position sensor related and/or engine misfire DTCs (P0340, P0341, P0345, P0346, P0365, P0366, P0390, P0391, P0301, P0302, P0303, P0304) due to the camshaft position sensor being out of specification. In addition, some vehicles may also experience rough idle or extended cranking.

SCION · 2014-02-14

Some 2013 model year FR-S vehicles may exhibit intake and/or exhaust camshaft position sensor related and/or engine misfire DTCs (P0340, P0341, P0345, P0346, P0365, P0366, P0390, P0391, P0301, P0302, P0303, and P0304) due to the camshaft position sensor clearance being out of specification. In addition, some vehicles may also experience rough idle or extended cranking. This bulletin provides inspection and repair procedures to improve this condition.

SUBARU · 2014-01-28

"DIFFICULTY STARTING, ROUGH IDLE, CAM POSITION OR MISFIRE DTCS P0340, P0341, P0345, P0346, P0365, P0366, P0390, P0391, P0301, P0302, P0303 OR P0304 - THIS BULLETIN PROVIDES INSPECTION AND REPAIR PROCEDURES FOR INTAKE AND EXHAUST CAMSHAFT POSITION-RELATED AND/OR ENGINE MISFIRE DTCS FOR THE FA AND FB ENGINE-EQUIPPED MODELS LISTED ABOVE."

SCION · 2013-08-30

Some 2013 model year FR-S vehicles may exhibit intake and/or exhaust camshaft position sensor related and/or engine misfire DTCs (P0340, P0341, P0345, P0346, P0365, P0366, P0390, P0391, P0301, P0302, P0303, and P0304) due to the camshaft position sensor clearance being out of specification. In addition, some vehicles may also experience rough idle or extended cranking. This bulletin provides inspection and repair procedures to improve this condition.

SUBARU · 2012-12-03

DTCS P0365, P0366, P0390 AND P0391 MISFIRE DTCS P0301, P0302, P0303 AND P0304

VOLKSWAGEN · 2012-10-19

Tech Tips (2011-2012 3.6L Routan ? Fault Codes P06DD, P000D, or P0390 After Cylinder Head Replacement): This document informs to verify that the oil galley bolts were transferred (see pictures in this document) when the cylinder head was replaced.