U0125 · Материалы производителя

JEEP · 2025-09-27

Not applicable to vehicles built for US market. Multiple Systems Repair Bundle Campaign Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U11E3-00 - TCM Lost Communication With ESM On DPT CAN. ● B15A1-00 - Media Port 1 Connection. ● U11C2 - Lost Transmission Message. ● U11E4-00 - CAN Communication Messages Missing. ● U120C - Lost Brake Booster Signal. ● U1216-00 - Lost Communication With DASM. ● U121E-00 - Lost Communication With Steering Wheel Cruise Control Switch. ● U1267-00 - No Valid Data From ESM On CAN-C Or CAN-DPT. ● U12A8 - Lost Communication With Master Cylinder Pressure Sensor. ● U1465-00 - Implausible Driver Shift Request Signal Received. ● U1466-00-…

DODGE · 2023-10-26

Dynamic Sensor Prior to replacing this part, please ensure all the pre-diagnostic & diagnostic procedures have been completed with emphasis on wiring and connector integrity. If codes C006A-28, U0125-00, or C006A-46 are present, warranty analysis suggests a high likelihood of an intermittent connection at or near the wiring connector, especially if the vehicle is a pursuit variant. Please verify wiring per diagnostic procedures, as well as removal & installation guidance called out in the service manual before replacement.

DODGE · 2022-01-20

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): U0101 - Lost Communication With TCM. U0102 - Lost Communication With Transfer Case Control Module / AWD. U0103 - Lost Communication With Electric Gear Shift Module. U0104 - Lost Communication With Cruise Control Module. U0125 - Lost Communication With Dynamics Sensor. U0128 - Lost Communication With Park Brake Control Module. U0129 - Lost Communication With Brake System Control Module 1. U0140 - Lost Communication With Body Control Module. U0141 - Lost Communication With Ipm…

DODGE · 2022-01-20

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): U0101 - Lost Communication With TCM. U0102 - Lost Communication With Transfer Case Control Module / AWD. U0103 - Lost Communication With Electric Gear Shift Module. U0104 - Lost Communication With Cruise Control Module. U0125 - Lost Communication With Dynamics Sensor. U0128 - Lost Communication With Park Brake Control Module. U0129 - Lost Communication With Brake System Control Module 1. U0140 - Lost Communication With Body Control Module. U0141 - Lost Communication With Ipm…

CHRYSLER · 2022-01-20

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): U0101 - Lost Communication With TCM. U0102 - Lost Communication With Transfer Case Control Module / AWD. U0103 - Lost Communication With Electric Gear Shift Module. U0104 - Lost Communication With Cruise Control Module. U0125 - Lost Communication With Dynamics Sensor. U0128 - Lost Communication With Park Brake Control Module. U0129 - Lost Communication With Brake System Control Module 1. U0140 - Lost Communication With Body Control Module. U0141 - Lost Communication With Ipm…

CHEVROLET, GMC · 2019-12-18

N192285670 - SUB - Certain 2020 model year Chevrolet Equinox and GMC Terrain vehicles may have an electronic brake control module (EBCM) that could set diagnostic trouble codes U0125 or U0151. If this happens, the driver's information center (DIC) will display "Service ESC", "Service Stabilitrak" or "Service Parking Brake". The function of ESC/Stabilitrak/Park Brake will be compromised. It may clear in a subsequent key cycle (requires an EBCM power cycle). Dealers will reprogram the EBCM.

BUICK · 2019-08-13

N192266900 - Service Update. A Service Stabilitrak message may be displayed on the driver information center, setting DTC U0125/U0151. The Electronic Stability Control (ESC) may be disabled during the ignition cycle when the message is displayed but function may return to work properly after vehicle sleep cycle. Dealers are to reprogram the electronic brake control module.

CHEVROLET, GMC · 2018-11-19

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.

CHEVROLET, GMC · 2015-09-21

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.

CHEVROLET, GMC · 2015-06-01

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.

BUICK, CADILLAC, CHEVROLET, GMC · 2015-05-14

This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.

CHEVROLET, GMC · 2015-04-30

This Preliminary Information communication provides information to the technician about vehicles that have may an intermittent Service Traction/Stability, ABS indicator or Service All wheel Drive message on the Driver Information Center. Technician may find Diagnostic Trouble Codes U0125 00 U0074 00 U0073 and or C0045 C0050 symptom 06. Technician will need to inspect the X411 connecter for a wire break inside the wire harness. Also inspect the wire harness insulation within 1 inch of the X411 before and after connecter. Repair any damaged wiring to correct the concern.

BUICK, CADILLAC, CHEVROLET, GMC · 2014-02-10

This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.

CHEVROLET, GMC · 2013-05-16

This Preliminary Information communication provides information to the technician about vehicles that have may an intermittent Service Traction/Stability, ABS indicator or Service All wheel Drive message on the Driver Information Center. Technician may find Diagnostic Trouble Codes U0125 00 U0074 00 U0073 and or C0045 C0050 symptom 06. Technician will need to inspect the X411 connecter for a wire break inside the wire harness. Also inspect the wire harness insulation within 1 inch of the X411 before and after connecter. Repair any damaged wiring to correct the concern.

CHEVROLET, GMC · 2013-03-15

This Preliminary Information communication provides information to the technician about vehicles that have may an intermittent Service Traction/Stability, ABS indicator or Service All wheel Drive message on the Driver Information Center. Technician may find Diagnostic Trouble Codes U0125 00 U0074 00 U0073 and or C0045 C0050 symptom 06. Technician will need to inspect the X411 connecter for a wire break inside the wire harness. Also inspect the wire harness insulation within 1 inch of the X411 before and after connecter. Repair any damaged wiring to correct the concern.

BUICK, CADILLAC, CHEVROLET, GMC · 2012-10-11

This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.