B1032 · 厂商技术资料

MAZDA · 2026-07-02

This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-016/26 05/06/26 DESCRIPTION Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) Customers having this concern should have their vehicle repaired…

MAZDA · 2026-05-07

DESCRIPTION Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) REPAIR PROCEDURE 1. Verify the customer concern. 2. Remove the front seat cushion trim and the front seat back trim for both the driver and passenger seats according to the instructions in…

MAZDA · 2025-01-22

Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side)

MAZDA · 2023-07-10

Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs B1030:13 and/or B1032:13 are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side)

MAZDA · 2023-03-22

Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side), B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side)

MAZDA · 2023-02-09

Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmer's fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side), B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side)

MAZDA · 2022-11-15

Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs "B1030:13" and/or "B1032:13" are stored. This is caused by the seat warmer's fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. - B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) - B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side)