P1326 · 厂商技术资料

HYUNDAI · 2022-04-28

Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

HYUNDAI · 2022-04-28

Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

HYUNDAI · 2022-04-28

Hyundai is conducting a service campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

HYUNDAI · 2022-04-28

Certain vehicles that have completed Service Campaign 966 may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

KIA · 2022-04-21

SUBSEQUENT REPAIR ACTION: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2106Y/Z) - This bulletin provides information related to the Technical Service Bulletin previously published (PI2106) titled “Nu 2.0L GDI - Knock Sensor Detection System ECU Logic Improvement”. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

HYUNDAI · 2022-04-20

Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

HYUNDAI · 2022-04-15

Applicable vehicles with 2.0L T-GDI and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit Abnormal Noise or No Crank/No Start condition. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.

HYUNDAI · 2022-04-15

Certain vehicles with 2.0L T-GDI and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit abnormal noise or no crank/no start condition related to connecting rod bearing wear or damage. This Dealer Best Practice outlines the service procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results, as well as related warranty coverage for the conditions outlined above.

KIA · 2022-03-23

SUBSEQUENT REPAIR ACTION: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2105Y/Z) - This bulletin provides information related to the Technical Service Bulletin previously published (PI2105) titled "Nu 2.0L GDI - Knock Sensor Detection System ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

HYUNDAI · 2022-03-10

Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

HYUNDAI · 2022-03-08

Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

HYUNDAI · 2022-01-03

Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

KIA · 2021-12-23

PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1803Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1803 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

KIA · 2021-12-23

PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

HYUNDAI · 2021-12-21

Hyundai is conducting a service campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

KIA · 2021-11-04

PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1803Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1803 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

KIA · 2021-11-04

PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

HYUNDAI · 2021-11-03

Hyundai has launched a Service Campaign for applicable vehicles with 2.0L Turbo and 2.4L GDI engines that may experience the Check Engine warning lamp illuminated with DTC P1326.

HYUNDAI · 2021-11-03

Applicable vehicles with 2.0L T-GDI and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit Abnormal Noise or No Crank/No Start condition. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.

HYUNDAI · 2021-10-27

Hyundai is conducting a service campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

HYUNDAI · 2021-10-25

Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

KIA · 2021-09-23

TECHNICAL SERVICE BULLETIN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2002Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2002A, PI2002B and SC200**1) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

HYUNDAI · 2021-09-02

Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

HYUNDAI · 2021-09-02

Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

KIA · 2021-06-15

TECHNICAL SERVICE BULLETIN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2002Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in January 2021 (PI2002A and PI2002B, August 2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

HYUNDAI · 2021-05-11

Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

KIA · 2021-04-15

TECHNICAL SERVICE BULLETIN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2002Y/Z) - This bulletin provides information related to the Technical Service Bulletin previously published in January 2021 (PI2002A and PI2002B, August 2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

HYUNDAI · 2021-03-30

Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

HYUNDAI · 2020-12-21

Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results. Consult the Hyundai Warranty Policy & Procedures and the below chart to determine New or Reman engine usage.

HYUNDAI · 2020-12-21

Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.