P2610 · 厂商技术资料

CHRYSLER, DODGE · 2020-08-27

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with updated software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in memory:P0456 - EVAP System Small Leak. P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. In addition, customers with an (LD) pursuit vehicle may experience the following condition:An unpleasant odor in the vehicle under certain extreme ambient conditions(Sales Codes EZH with AHB or AHV only).

JEEP · 2020-08-22

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P2610 - PCM Internal Engine Off Timer Performance. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. U1424 - Implausible Engine Torque Signal Received DTC False Failure. P2097 - Downstream Fuel Trim System 1 Rich DTC Calibration Robustness Improvement. P2099 - Downstream Fuel Trim System 2 Rich DTC Calibration Robustness Improvement. U0402 - Implausible Data Received. B10EA - Blower Motor Control Circuit High. B10E9 - Blower Motor Control Circuit Low. P0456 - EVAP System Small…

JEEP · 2020-08-22

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P2610 - PCM Internal Engine Off Timer Performance. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. U1424 - Implausible Engine Torque Signal Received DTC False Failure. P2097 - Downstream Fuel Trim System 1 Rich DTC Calibration Robustness Improvement. P2099 - Downstream Fuel Trim System 2 Rich DTC Calibration Robustness Improvement. U0402 - Implausible Data Received. B10EA - Blower Motor Control Circuit High. B10E9 - Blower Motor Control Circuit Low. P0456 - EVAP System Small…

MERCEDES-BENZ · 2020-06-18

The check engine indicator light in the instrument cluster may be illuminated with one of the following fault codes: P261029, P02FF85, or P02FF02 stored in the engine control unit (N3/10). The time in instrument cluster is implausible due to an internal reset. If no other complaints exist then check for and perform any available software updates for the following control units: - Motor electronics (N3/10) - Powertrain control unit (N127) - Instrument cluster (A1) If all three control units have the latest software installed and the complaint continues to occur then proceed with replacement of the instrument cluster (A1) Should the complaint re-occur after the instrument cluster has been replaced then open a PTSS case with the following information: - Control units logs for the ME, PTCU,…

MERCEDES-BENZ · 2020-05-19

Check engine indicator light active and fault code P261029/P02FF85/P02FF02 stored in engine control unit

JEEP · 2020-05-16

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs:P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit…

MAZDA · 2020-01-23

Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed.à ̄‚· P2610:00: Instrument cluster internal engine off timer performance problem à ̄‚· P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display “F0-002” during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle…

MERCEDES-BENZ · 2020-01-07

Check engine indicator light active and fault code P261029/P02FF85/P02FF02 stored in engine control unit

MERCEDES-BENZ · 2019-11-19

Model series 253: Time/date and trip computer reset and/or check engine light in instrument cluster with DTC P261029 in ME

SUBARU · 2019-08-05

This bulletin announces availability of a new Engine Control Module (ECM) for the models listed above designed to address DTC P2610: “ECM/PCM ENGINE OFF TIMER PERFORMANCE”. Under certain RARE conditions, an electrostatic surge may influence the ECM’s internal timer used after the engine is turned off and store a DTC P2610 in memory. Hardware in the ECM has been changed to eliminate any impact from electrostatic surges.

SUBARU · 2019-07-30

This bulletin announces availability of a new Engine Control Module (ECM) for the models listed above designed to address DTC P2610: “ECM/PCM ENGINE OFF TIMER PERFORMANCE”. Under certain RARE conditions, an electrostatic surge may influence the ECM’s internal timer used after the engine is turned off and store a DTC P2610 in memory. Hardware in the ECM has been changed to eliminate any impact from electrostatic surges.

MERCEDES-BENZ · 2019-06-20

Model series 253 modification year 18/1: Engine indicator lamp active and fault code P261029 stored in engine control unit

MERCEDES-BENZ · 2019-05-20

Model series 253: Engine indicator lamp active and fault code P261029 stored in engine control unit

MERCEDES-BENZ · 2019-04-02

Model series 253: Engine indicator lamp active and fault code P261029 present in engine control unit

MERCEDES-BENZ · 2019-02-22

Model series 253: Engine indicator lamp active and fault code P261029 present in engine control unit

TOYOTA · 2019-01-16

TSB: Some 2016 - 2018 model year Prius and Tacoma, 2017 - 2018 model year Prius Prime and Sienna, and 2018 model year Camry and Camry Hybrid vehicles may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P261093 (ECM/PCM Engine Off Timer Performance No Operation) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition.

MAZDA · 2019-01-04

Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than…

LEXUS · 2018-12-14

TSB: Some 2016 ? 2017 model year IS200t, IS300, RC200t, and RX350, 2016 ? 2018 model year GS200t, GS300, GS350, and RC300, and 2018 model year IS300, IS350, and RC350 vehicles may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P261093 (ECM/PCM Engine Off Timer Performance No Operation) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module [PCM]) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition.

MAZDA · 2018-05-08

Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more…

LEXUS · 2018-01-23

TSB: Some 2014 - 2017 model year Lexus vehicles may exhibit a MIL "ON" condition with Diagnostic Trouble Code (DTC) P2610 (Engine Off Timer Performance) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module [PCM]) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure below to address this condition.

SCION · 2018-01-02

TSB: Some 2016 model year iM vehicles may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P2610 (Engine Off Timer Performance) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module [PCM]) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure below to address this condition.

TOYOTA · 2017-12-21

TSB: Some 2014 ? 2018 model year Toyota vehicles may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P2610 (Engine Off Timer Performance) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module [PCM]) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure below to address this condition.

MAZDA · 2017-12-18

Some vehicles may experience the CHECK ENGINE LIGHT OIN with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery voltage low input.

LEXUS · 2017-10-23

TSB: Some 2016 model year GS F and 2015 ? 2016 model year RC F vehicles may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P2610 (Engine Off Timer Performance) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition.

DODGE · 2017-09-02

Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software.This bulletin applies to vehicles within the following markets/countries: NAFTA, LATAM, EMEA and APAC. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory:2.4L EngineP0335 - Crankshaft Position Sensor Circuit. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P1607 - PCM Internal Shutdown Timer Rationality - (Powertrain Control Module). P2610 - PCM Internal Engine Off Timer Performance - (Powertrain Control Module). P0456 - EVAP…

DODGE · 2017-09-02

Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set:2.4L Engines (Sales Code ED3 or ED7)P0335 - Crankshaft Position Sensor Circuit. P030X - Cylinder X Misfire Improvements when P0335 (Crankshaft Position Sensor Circuit) is present. P0456 - EVAP System Small Leak. P1607 - PCM Internal Shutdown Timer Slow Rationality. P2610 - PCM Internal Engine Off Timer Performance. Customers may also notice one or more of the following symptoms:When coming to a stop or making a turn, their vehicle would…

SCION · 2017-08-29

TSB: Some 2015 model year iQ vehicles may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P2610 (Engine Off Timer Performance) present. The Engine Control Module/ECM (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure below to address this condition.

CHRYSLER, DODGE · 2017-08-23

Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming of the Powertrain Control Module (PCM) with the latest software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs: P000B - Bank 1 Camshaft 2 Position Slow Response. P0016 - Crankshaft/Camshaft Timing Misalignment - Bank 1 Sensor 1. P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0441 - EVAP Purge System Performance. P0455 - EVAP System Large Leak. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. Customers may also notice the following condition(s): Brief…

CHRYSLER, DODGE · 2017-08-18

Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DiagnosticTrouble Codes (DTCs) have been set:P2066 - Fuel Level Sensor 2 Performance (Sales Codes ERB with AHB or AHV only). P0335 - Crankshaft Position Sensor Circuit. P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. In addition to the above DTCs, this software release also includes:Enhancements to the disable misfire monitor when P0335 is present. Add a global disable to small leak monitor when the fuel level is above88%. Update small leak diagnostic to…

TOYOTA · 2017-08-18

TSB: Some 2014 ? 2016 model year Highlander HV, 2015 Tacoma, 2015 ? 2016 Venza, 2015 ? 2017 4Runner, Avalon, Camry, and 2016 ? 2017 Avalon HV and Camry HV vehicles may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P2610 (ECM/PCM Engine Off Timer Performance) present. The Engine Control Module (ECM) SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure below to address this condition.