P061B · 原廠技術資料

RAM · 2023-01-12

Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: **P0299 - Turbocharger Underboost.** P026B-00 - Injection Timing Performance. P061B-00 - Internal Control Module Torque Calculation Performance. P1451-00 - Diesel Particulate Filter System Performance. P0755-00 - Shift Solenoid ?B? (DG7 Trans Sales Code). P0765-00 - Shift Solenoid ?D?(DG7 Only). P0401-00 - EGR System Performance Customers may also experience the following: **Service Exhaust System message in the Electronic Vehicle Information Center (EVIC) with no MIL.** Improvements to cold temperature engine rpm fluctuation. Reduce…

MAZDA · 2022-11-22

Some customers may complain that the CHECK ENGINE light turns ON after a cold start, then exhibits lack of power from the engine with DTC P061B:00 stored in memory. This is caused by improper control software of the PCM. To eliminate this concern, the PCM control software has been modified.

RAM · 2022-10-25

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set: P0299-00 - Turbocharger Underboost. P026B-00 - Injection Timing Performance. P061B-00 - Internal Control Module Torque Calculation Performance. P1451-00 - Diesel Particulate Filter System Performance. P0755-00 - Shift Solenoid "B"(DG7 Trans Sales Code). P0765-00 - Shift Solenoid "D"(DG7 Only). P0401-00 - EGR System Performance. The following improvements are also included in this update:Improvements to cold temperature engine rpm…

MAZDA · 2022-08-03

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). - DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Condition Condition Description A When cranking is interrupted (likely occurs when the brake pedal is released during cranking) B When accelerating from 1300-1600 rpm with wide open throttle Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

JEEP · 2022-05-13

Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). P061B-00 - Internal Control Module Torque Calculation Performance. P061B-00 DTC may set after driving on snow/ice in 2WD and Traction Control System (TCS) turned off. P06A3-00 - Sensor Reference Voltage "D" Circuit/Open. P0697-00 - Sensor Reference Voltage 3 Circuit. Other software enhancement included with this update:On Board Fuel Consumption Monitoring Updates (China Only).…

JEEP · 2022-05-13

Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). U0293-00 - Lost Communication With Hybrid Control Module. P0732-00 - Gear 2 Shift Incorrect Ratio. P061B-00 - Internal Control Module Torque Calculation Performance. Other software enhancement::2?1 downshift improvement. Additional module flashes are required for this update to be effective, the following modules are all to be updated along with this PCM update:Hybrid Control Processor (HCP), Auxiliary Hybrid Control Processor (AHCP) also known as the Power Invertor Module…

JEEP · 2022-03-12

Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). P061B-00 - Internal Control Module Torque Calculation Performance.P061B-00 DTC may set after driving on snow/ice in 2WD and Traction Control System (TCS) turned off. P06A3-00 - Sensor Reference Voltage "D" Circuit/Open. P0697-00 - Sensor Reference Voltage 3 Circuit. Other software enhancement included with this update:On Board Fuel Consumption Monitoring Updates (China Only).…

FORD · 2022-01-07

Some 2020-2022 Police Interceptor Utility hybrid vehicles may exhibit multiple warning messages, various drivability concerns and/or an illuminated malfunction indicator lamp (MIL) with DTC P061B. This may be due to incorrectly installed or usage of additional police equipment with the vehicle not running. Refer to the Police Interceptor Utility and Hybrid Utility Modifiers Guide available on the Professional Technician System (PTS) website Service Tips tab for guidelines. Equipment should only use the rear power access point provided and not the 12V cranking/auxiliary batteries. The vehicle will go to sleep after the ignition key is removed and is not designed to power equipment when the vehicle is not running. The Police Engine Idle feature can be used, if equipped, to allow the vehicle…

FORD · 2021-12-15

Some 2020-2022 Police Interceptor Utility hybrid vehicles may exhibit multiple warning messages, various drivability concerns and/or an illuminated malfunction indicator lamp (MIL) with DTC P061B. This may be due to incorrectly installed or usage of additional police equipment with the vehicle not running. Refer to the Police Interceptor Utility and Hybrid Utility Modifiers Guide available on the Professional Technician System (PTS) website Service Tips tab for guidelines. Equipment should only use the rear power access point provided and not the 12V cranking/auxiliary batteries. The vehicle will go to sleep after the ignition key is removed and is not designed to power equipment when the vehicle is not running. If auxiliary police equipment needs to be powered for an extended time after…

ACURA · 2021-11-23

Service Bulletin - The MIL comes on with DTC P061B (PCM Internal Malfunction) is stored.

ACURA · 2021-10-26

Service Bulletin - The MIL comes on with DTC P061B (PCM Internal Malfunction) is stored.

HONDA · 2021-10-26

Service Bulletin - The MIL comes on with DTC P061B (PCM Internal Malfunction) is stored.

HONDA · 2021-10-06

Service Bulletin - The MIL comes on with DTC P061B (PCM Internal Malfunction) is stored.

HONDA · 2021-09-07

Service Bulletin - The MIL comes on with DTC P061B (PCM Internal Malfunction) is stored.

ACURA · 2021-09-03

Service Bulletin - The MIL comes on with DTC P061B (PCM Internal Malfunction) is stored.

JEEP · 2021-08-26

Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTC). U0293-00 - Lost Communication With Hybrid Control Module. P0732-00 - Gear 2 Shift Incorrect Ratio. P061B-00 - Internal Control Module Torque Calculation Performance. Other software enhancement::2?1 downshift improvement. Additional module flashes are required for this update to be effective, the following modules are all to be updated along withthis PCM update:Hybrid Control Processor (HCP), Auxiliary Hybrid Control Processor (AHCP) also known as the Power Invertor Module (PIM).…

JEEP · 2021-08-26

Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTC). P061B-00 - Internal Control Module Torque Calculation Performance.P061B-00 DTC may set after driving on snow/ice in 2WD and Traction Control System (TCS) turned off. P06A3-00 - Sensor Reference Voltage "D" Circuit/Open. P0697-00 - Sensor Reference Voltage 3 Circuit. Additional module flashes are required for this update to be effective, the following modules are all to be updated…

NISSAN · 2021-08-26

MIL ON WITH DTC P060A, P060C, AND/OR P061B STORED IN THE ECM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

RAM · 2021-08-12

When The PTO Is Engaged, The Engine RPM Will Surge And Cannot Increase above 1100 RPM. Diagnostic Trouble Codes (DTCs) P061B ? Internal Control Module Torque Performance, And/Or P064B ? PTO Control Module, Set.

RAM · 2021-08-12

When The PTO Is Engaged, The Engine RPM Will Surge And Cannot Increase above 1100 RPM. Diagnostic Trouble Codes (DTCs) P061B ? Internal Control Module Torque Performance, And/Or P064B ? PTO Control Module, Set.

ACURA · 2021-08-06

Service Bulletin - The MIL comes on with DTC P061B (PCM Internal Malfunction) is stored.

RAM · 2021-07-27

When The PTO Is Engaged, The Engine RPM Will Surge And Cannot Increase above 1100 RPM. Diagnostic Trouble Codes (DTCs) P061B ? Internal Control Module Torque Performance, And/Or P064B ? PTO Control Module, Set.

RAM · 2021-05-14

When The PTO Is Engaged, Engine RPM Will Not Exceed 1100 RPM And The Engine Surges. Diagnostic Trouble Codes (DTCs) P061B ? Internal Control Module Torque Performance, And/Or P064B ? PTO Control Module, Set.

MAZDA · 2021-04-02

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

MERCEDES-BENZ · 2021-03-02

When accelerating at low speeds (slow roll at < 9 mph, 2nd gear), the engine limp-home mode may be triggered which in turn limits the amount of power available. When a fault occurs, the fault message ESP off or a fault message from the driver assistance systems is displayed. The quick test shows that fault code P061B62 is stored Note: It is possible to continue driving slowly. The fault is reset after an ignition cycle and normal driving is possible again.

MERCEDES-BENZ · 2021-01-08

When accelerating at low speeds (slow roll at less than 9 mph, 2nd gear), the engine limp-home mode may be triggered which in turn limits the amount of power available. When a fault occurs, the fault message ESP off or a fault message from the driver assistance systems is displayed. The quick test shows that fault code P061B62 is stored Note: It is possible to continue driving slowly. The fault is reset after an ignition cycle and normal driving is possible again.

RAM · 2020-09-15

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P1D73-00 - AGS Performance. P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B…

RAM · 2020-09-15

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module (ECM) / Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1D73-00 - AGS Performance. P061B - Internal Control Module Torque Calculation Performance. P064B-00 - PTO Control Module. The customer may also notice the following:Power Take Off (PTO) intermittently turns off with no DTCs. In addition the following software enhancements are included:System Improvement for PTO operation. wiTECH Mass Air Flow (MAF) data parameter improvement. Enabling wiTECH Particulate…

ACURA · 2020-03-27

Service Bulletin - The Malfunction Indicator Lamp (MIL) may illuminate and set DTC P061B (PCM internal malfunction torque calculation).

RAM · 2020-03-04

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B - Internal Control Module…