P0810 · Manufacturer communications

JEEP · 2025-07-19

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle mustexhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P04B5 - Fuel Fill Door Stuck Open. ● P1D83 - Implausible Engine Oil Temperature Signal Received.** ● P2450 - Fuel Tank Isolation Valve Stuck Open. ● P0032 - O2 Sensor 1/1 Heater Circuit High. ● P2097 - Downstream Fuel Trim System 1 Rich. ● P0171 - Fuel System 1/1 Lean. ● P0300 - Multiple Cylinder Misfire. ● P06E4 - Control Module Wake-Up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault.…

JEEP · 2025-05-24

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P2450 - Fuel Tank Isolation Valve Stuck Open.** ● P0032 - O2 Sensor 1/1 Heater Circuit High. ● P2097 - Downstream Fuel Trim System 1 Rich. ● P0171 - Fuel System 1/1 Lean. ● P0300 - Multiple Cylinder Misfire. ● P06E4 - Control Module Wake-Up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. Customers may also experience one or more of the following: ● **""Service Hybrid System"" message…

JEEP · 2025-01-12

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0810-00 - Clutch Position Control Error. This bulletin involves reprogramming the TCM with the latest available software."

JEEP · 2025-01-11

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0810-00 - Clutch Position Control Error. ● P16F0-00 - SPI Comm Hardware Fault. Customers may also comment on one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning indicator is on. NOTE: Require key cycle to recover. ● Shifts rough occasionally when coming down to a stop. ● Shifts rough occasionally when accelerating. ● Shifts rough when transitioning from EV to Hybrid operation on low SoC. ● Shifts rough when engines starts. ● On part throttle accelerations…

JEEP · 2025-01-11

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0810 - Clutch Position Control Error. Customers may also experience one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and in EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning light on. NOTE: A key cycle will recover these symptoms. The following software enhancement is available: ● Modified the P0810 - Clutch Position Control Error set parameters. This bulletin involves reprogramming the TCM with the latest available software."

JEEP · 2025-01-11

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P06E4 - Control Module Wake-up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. Customers may experience one or more of the following: ● Vehicle loses propulsion capability. ● 'Shift To Park' notification on. ● 'Service Transmission' warning light on. ● Requires key cycle to recover. ● Shifts rough occasionally. ● Harsh shifts when tipping in during a coast down. ● Shifts roughly during coast…

JEEP · 2025-01-11

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0810 - Clutch Position Control Error. Customers may also experience one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and in EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning light on. NOTE: A key cycle will recover these symptoms. The following software enhancement is available: ● Modified the P0810 - Clutch Position Control Error set parameters This bulletin involves reprogramming the TCM with the latest available software. "

JEEP · 2025-01-11

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0810 - Clutch Position Control Error. Customers may also experience one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and in EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning light on. NOTE: A key cycle will recover these symptoms. The following software enhancement is available: ● Modified the P0810 - Clutch Position Control Error set parameters This bulletin involves reprogramming the TCM with the latest available software. "

JEEP · 2025-01-11

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1614-00 - ECU Reset/Recovery Occurred. ● P0810-00 - Clutch Position Control Error. Customers may also comment on one or more of the following: ● Customer may not continue with rock cycle maneuver due to the wrong message ""Shift To P then Desired Gear"" displayed on the Instrument Panel Cluster (IPC). ● K0 Adaptation routine runs when vehicle stationary and EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning indicator is on. NOTE: Requires key cycle to recover. This bulletin involves reprogramming the TCM with the latest available software."

JEEP · 2024-10-04

"Flash: Transmission Control Module (TCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P1614-00 - ECU Reset/Recovery Occurred.** ● P0810-00 - Clutch Position Control Error. Customers may also comment on one or more of the following: ● **Customer may not continue with rock cycle maneuver due to the wrong message ""Shift To P then Desired Gear"" displayed on the Instrument Panel Cluster (IPC).** ● K0 Adaptation routine runs when vehicle stationary and EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning indicator is on. NOTE: Requires key cycle to recover. This bulletin involves reprogramming the TCM with the latest available…

JEEP · 2024-06-20

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P06E4 - Control Module Wake-up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. Customers may experience one or more of the following: ● Vehicle loses propulsion capability. ● 'Shift To Park' notification on. ● 'Service Transmission' warning light on. ● Requires key cycle to recover. ● Shifts rough occasionally. ● Harsh shifts when tipping in during a coast down. ● Shifts roughly during coast…

JEEP · 2024-06-20

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 Sensor 1/1 Heater Circuit High. ● P2097 - Downstream Fuel Trim System 1 Rich. ● P0171 - Fuel System 1/1 Lean. ● P0300 - Multiple Cylinder Misfire. ● P06E4 - Control Module Wake-Up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. Customers may also experience one or more of the following: ● Vehicle misfires. ● Low speed engine stall at idle. ● Difficulty shifting out of 4LO. ● Idle…

JEEP · 2024-06-08

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P06E4 - Control Module Wake-up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. Customers may experience one or more of the following: ● **Vehicle loses propulsion capability. ● 'Shift To Park' notification on. ● 'Service Transmission' warning light on. ● Requires key cycle to recover.** ● Shifts rough occasionally. ● Harsh shifts when tipping in during a coast down. ● Shifts roughly during…

JEEP · 2024-06-08

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0810-00 - Clutch Position Control Error. Customers may also comment on one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning indicator is on. NOTE: Requires key cycle to recover. This bulletin involves reprogramming the TCM with the latest available software."

JEEP · 2024-06-08

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0032 - O2 Sensor 1/1 Heater Circuit High. ● P2097 - Downstream Fuel Trim System 1 Rich. ● P0171 - Fuel System 1/1 Lean. ● P0300 - Multiple Cylinder Misfire.** ● P06E4 - Control Module Wake-Up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. Customers may also experience one or more of the following: ● **Vehicle misfires. ● Low speed engine stall at idle.** ● Difficulty shifting out of 4LO. ●…

JEEP · 2024-06-08

"Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P06E4 - Control Module Wake-up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. Customers may also experience the following: ● Transmission torque calculation issues. This bulletin involves reprogramming the Powertrain Control Module (PCM), Transmission Control Module (TCM) and the AHCP also known as Power Inverter Module (PIM), with the latest…

JEEP · 2024-05-23

"Flash: Transmission Control Module (TCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC):** ● P0810 - Clutch Position Control Error. Customers may also experience one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and in EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning light on. NOTE: A key cycle will recover these symptoms. **The following software enhancement is available: ● Modified the P0810 - Clutch Position Control Error set parameters.** **This bulletin involves reprogramming the TCM with the latest available software.** NOTE: **Please be sure that the 04B recall is completed prior to performing this TSB.…

JEEP · 2024-05-23

"Flash: Transmission Control Module (TCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC):** ● P0810 - Clutch Position Control Error. Customers may also experience one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and in EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning light on. NOTE: A key cycle will recover these symptoms. **The following software enhancement is available: ● Modified the P0810 - Clutch Position Control Error set parameters.** **This bulletin involves reprogramming the TCM with the latest available software.** NOTE: **Please be sure that the 04B recall is completed prior to performing this TSB.…

JEEP · 2024-05-23

"Flash: Transmission Control Module (TCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC):** ● P0810 - Clutch Position Control Error. Customers may also experience one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and in EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning light on. NOTE: A key cycle will recover these symptoms. **The following software enhancement is available: ● Modified the P0810 - Clutch Position Control Error set parameters.** **This bulletin involves reprogramming the TCM with the latest available software.** NOTE: **Please be sure that the 04B recall is completed prior to performing this TSB.…

JEEP · 2024-05-10

"Flash: Transmission Control Module (TCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0810-00 - Clutch Position Control Error. ● P16F0-00 - SPI Comm Hardware Fault. Customers may also comment on one or more of the following: ● K0 Adaptation routine runs when vehicle stationary and EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning indicator is on. NOTE: Require key cycle to recover. ● Shifts rough occasionally when coming down to a stop. ● Shifts rough occasionally when accelerating. ● Shifts rough when transitioning from EV to Hybrid operation on low SoC. ● Shifts rough when engines starts. ● On part throttle accelerations…

JEEP · 2024-05-10

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0810-00 - Clutch Position Control Error. This bulletin involves reprogramming the TCM with the latest available software. NOTE: Please be sure that the 04B recall is completed prior to performing this TSB. This TCM software update is covered by the 04B recall if still incomplete."

JEEP · 2024-05-09

"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P06E4 - Control Module Wake-up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. **Customers may experience one or more of the following: ● Shifts rough occasionally. ● Harsh shifts when tipping in during a coast down. ● Shifts roughly during coast down.** This bulletin involves reprogramming the TCM, Powertrain Control (PCM) and the Auxiliary Hybrid Control Processor (AHCP) also known as…

JEEP · 2024-05-09

"Flash: Powertrain Control Module (PCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P06E4 - Control Module Wake-up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. **Customers may also experience one or more of the following: ● Difficulty shifting out of 4LO. ● Idle creep while in 4LO with transmission in neutral.** This bulletin involves reprogramming the PCM, Transmission Control Module (TCM) and the Auxiliary Hybrid Control Processor (AHCP) also known as Power Inverter…

JEEP · 2024-05-09

"Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P06E4 - Control Module Wake-up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. **Customers may also experience the following: ● Transmission torque calculation issues.** This bulletin involves reprogramming the Powertrain Control Module (PCM), Transmission Control Module (TCM) and the AHCP also known as Power Inverter Module (PIM), with the…

JEEP · 2024-05-02

"Flash: Transmission Control Module (TCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P06E4 - Control Module Wake-up Circuit Performance. ● B12B4 - Charge Status Indicator Module Internal. ● P061B - Internal Control Module Torque Calculation Performance. ● P0810 - Clutch Position Control Error. ● P2885 - Engine Disconnect Clutch Engagement Fault. This bulletin involves reprogramming the TCM, Powertrain Control Module (PCM) and the Auxiliary Hybrid Control Processor (AHCP) also known as Power Inverter Module (PIM), with the latest available software."

AUDI · 2023-10-09

This bulletin provides information for when there is a Gearbox Malfunction warning stored in the TCM; DTCs P176F00, P176E00, P175E00, P175D00, P189900, P060700, P081000.

PORSCHE · 2023-03-23

Technical information on fault memory entry P081000, in the transmission electronics control unit

JEEP · 2017-10-17

Customer Satisfaction Notification T52 The vehicle speed on about 24,000 of the above vehicles maybe limited if certain conditions are met. This can occur if the vehicle is brought to a full stop and the gear shifter is immediately moved from ?DRIVE? to ?PARK? and then the key position is changed from ?RUN? to ?ACC?. This action will cause the transmission to be limited to one gear and a maximum speed of 30 ? 45 mph and will illuminate the Malfunction Indicator Lamp (MIL) on the instrument cluster and will set P0810 fault code. Reprogram the transmission control module.

JEEP · 2017-09-17

Customer Satisfaction Notification T52 Reprogram Transmission ControlModule The vehicle speed on about 24,000 of the above vehicles maybe limited if certain conditions are met. This can occur if the vehicle is brought to a full stop and the gear shifter is immediately moved from ?DRIVE? to ?PARK? and then the key position is changed from ?RUN? to ?ACC?. This action will cause the transmission to be limited to one gear and a maximum speed of 30 ? 45 mph and will illuminate the Malfunction Indicator Lamp (MIL) on the instrument cluster and will set P0810 fault code. Reprogram the transmission control module.

JEEP · 2017-07-19

Transmission, Valve Body If you have a 2017 Cherokee equipped with a 3.2L engine that has set P0810-00 DTC please ensure TCM is updated to the latest level.