C10EA · Communications du constructeur

CHRYSLER · 2026-09-02

ACTUATOR Park Brake Do NOT replace actuator before checking for latest ABS software referencing TSB 08-010-26 and TSB 08-066-26. This update will eliminate the false occurrence of the DTCs below: C10EA-00 - Left Park Brake Actuator C10EB-00 - Right Park Brake Actuator C10EC-00 - Park Brake Actuator Correlation

JEEP · 2026-08-26

Headlamp And Dash Wiring Not Secure Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C10D0 - Electronic Park Brake System Failure. ● C10EA - 01 Left Park Brake Actuator - General Electrical Failure. ● C10D0 - 4B Electronic Park Brake Module - Over Temperature. ● C10D0 - 92 Electronic Park Brake Module-Performance or Incorrect Operation. ● C10D0 - 9A Electronic Park Brake Module-Component or System Operating Conditions. ● C2222 - 68 Improper Power Down-Event Information. ● U2006 - 64 EPB Status - Signal Plausibility Failure. NOTE: The above DTCs will only occur when there has been wire damage. Repair the damage following published repair methods. Submit repair…

CHRYSLER · 2026-02-14

Flash: Anti-Lock Brakes (ABS) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C151D-00 - Tire Pressure Sensor Location Undetermined. ● C10EA-00 - Left Park Brake Actuator. ● C10EB-00 - Right Park Brake Actuator. ● C10EC-00 - Park Brake Actuator Correlation. Customers may also comment on one or more of the following: ● The vehicle will not shift out of Park. ● Electronic Parking Brake (EPB) is not responding and not allowing the driver to release EPB. ● The Service TPM System message may display on the cluster after a tire rotation. NOTE: The vehicle will not automatically relearn tire locations and the process will have to be manually performed by a…

CHRYSLER · 2026-01-23

Flash: Anti-Lock Brakes (ABS) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **C151D-00 - Tire Pressure Sensor Location Undetermined NOTE: DTC sets in the Radio Frequency Hub Module (RFHM).** ● C10EA-00 - Left Park Brake Actuator. ● C10EB-00 - Right Park Brake Actuator. ● C10EC-00 - Park Brake Actuator Correlation. Customers may also experience one or more of the following: ● Electronic Parking Brake (EPB) is not responding and not allowing the driver to release EPB. ● **The Service TPM System message may display on the cluster after a tire rotation. NOTE: The vehicle will not automatically relearn tire locations and the process will have to be manually…

CHRYSLER · 2026-01-14

Flash: Anti-Lock Brakes (ABS) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C10EA-00 - Left Park Brake Actuator. ● C10EB-00 - Right Park Brake Actuator. ● C10EC-00 - Park Brake Actuator Correlation. Customers may also experience one or more of the following: ● Electronic Parking Brake (EPB) is not responding and not allowing the driver to release EPB. This bulletin involves reprogramming the ABS module with the latest available software.

JEEP · 2025-07-01

MP EPB SERVICE BRAKE MESSAGE ON THE CLUSTER AND LED LIGHT ON If any of the following DTCs come as ACTIVE: C10ED-00 Electronic Park Brake Switch LED- C10CD-01 Electronic Park Brake Switch-General Electrical Failure 1. Confirm customer's concern 2. If the DTCs come as STORED, clear them prior to performing any service steps. If the DTCs come as ACTIVE 3. Check that the battery connectors are properly seated as well as the ground connector. 4. Try disconnecting the battery for 5min to reset the module. 5. If the issue with the EPB is still present and there are ACTIVE DTCs, check for any loose connection at the Park Brake Switch or Brake System Module BEFORE replacing the Switch. If after disconnecting the switch and the module, any DTC goes from ACTIVE to STORE, clear them and do not…