P0152 · Communications du constructeur

JEEP · 2026-04-17

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). ● P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst…

JEEP · 2026-04-16

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst…

JEEP · 2026-04-16

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst…

JEEP · 2026-04-16

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst…

JEEP · 2026-02-17

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P08A6 - Gear Lever Position Sensor System – Multiple Sensor Correlation (Manual Transmission Only). ● P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. ● P0300 - Multiple Cylinder Misfire. ● P152E - Engine Hood Switch 2 Circuit High. ● P0032 - O2 Sensor 1/1 Heater Circuit High. ● P0038 - O2 Sensor 1/2 Heater Circuit High. ● P0052 - O2 Sensor 2/1 Heater Circuit High. ● P0058 - O2 Sensor 2/2 Heater Circuit High. ● P0132 - O2 Sensor 1/1 Circuit High. ● P0138 - O2 Sensor 1/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2…

JEEP · 2026-01-29

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P08A6 – Gear Lever Position Sensor System – Multiple Sensor Correlation (Manual Transmission Only). ● P152F – Engine Hood Switch 2 / Engine Hood Switch 1 Correlation.** ● P0300 - Multiple Cylinder Misfire. ● P152E - Engine Hood Switch 2 Circuit High. ● P0032 - O2 Sensor 1/1 Heater Circuit High. ● P0038 - O2 Sensor 1/2 Heater Circuit High ● P0052 - O2 Sensor 2/1 Heater Circuit High ● P0058 - O2 Sensor 2/2 Heater Circuit High. ● P0132 - O2 Sensor 1/1 Circuit High. ● P0138 - O2 Sensor 1/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High…

JEEP · 2026-01-24

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. **(Manual Transmission Only)** ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on the following: ● "Service Transmission” message on…

JEEP · 2025-07-18

Flash: Powertrain Control Module (PCM) Updates ustomers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P2504 - Charging System Output High. ● P0563 - Battery/System Voltage High. Customers may also experience one or more of the following: ● **Vehicle goes in limp mode within 1.6 km (1 mi) of driving while in 4LO, DTC P08A6 active and "Clutch Too Hot" message followed by "Service Transmission” message in the Instrument Panel Cluster (IPC).** ● The engine runs rough…

JEEP · 2025-07-09

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation.** ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 circuit high. ● P0152 - O2 Sensor 2/1 circuit high. ● P2504 - Charging system output high. ● P0563 - Battery/system voltage high. Customers may also experience the following: ● **"Service Transmission” message on in the Instrument Panel Cluster (IPC).** ● The engine runs rough. This bulletin involves reprogramming the PCM with the latest available software.

JEEP · 2025-07-09

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation.** ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● "Service Transmission”…

JEEP · 2025-03-01

Flash: Powertrain Control Module (PCM) Updates "Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection…

JEEP · 2024-09-05

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection…

JEEP · 2024-08-02

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High.** ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip…

JEEP · 2024-06-20

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P2504 - Charging System Output High. ● P0563 - Battery/system Voltage High (eTorque). Customers may also comment on the following: ● Customer finds Check Engine Light on and vehicle runs rough. This bulletin involves reprogramming the PCM with the latest available software."

JEEP · 2024-05-21

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0158 - O2 Sensor 2/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on due to Clutch Slip Detection with the transfer case in neutral. ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other Software Enhancements: ● Improvements to address vehicle no starts after replacing…

JEEP · 2024-05-03

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - closed loop fueling not achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 circuit high. ● P0152 - O2 Sensor 2/1 circuit high. ● P2504 - Charging system output high. ● P0563 - Battery/system voltage high. Customers may also experience the following: ● The engine runs rough. This bulletin involves reprogramming the PCM with the latest available software."

JEEP · 2024-05-03

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - closed loop fueling not achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 circuit high. ● P0152 - O2 Sensor 2/1 circuit high. ● P2504 - Charging system output high. ● P0563 - Battery/system voltage high. Customers may also experience the following: ● The engine runs rough. This bulletin involves reprogramming the PCM with the latest available software."

JEEP · 2024-05-02

"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0158 - O2 Sensor 2/2 Circuit High. ● P0152 - O2 Sensor 2/1 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. This bulletin involves reprogramming the PCM with the latest available software."

RAM · 2023-09-20

Malfunction Indicator Lamp (MIL) on, P0052, P0152, O2 Sensor High, P0113 Intake Air Sensor (IAT)

JEEP · 2022-12-01

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon furtherinvestigation the technician may find one or more of the following DTCs: P0300 - Multiple Cylinder Misfire. P152E - Engine Hood Switch 2 Circuit High. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. P0032 - O2 Sensor 1/1 Heater Circuit High. P0038 - O2 Sensor 1/2 Heater Circuit High. P0052 - O2 Sensor 2/1 Heater Circuit High. P0058 - O2 Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High. P2100 - Electronic Throttle Control Motor Circuit. In…

JEEP · 2022-12-01

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: P0300 - Multiple Cylinder Misfire. P0032 - O2-Sensor 1/1 Heater Circuit High. P0038 - O2-Sensor 1/2 Heater Circuit High. P0052 - O2-Sensor 2/1 Heater Circuit High. P0058 - O2-Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High. P2100 - Electronic Throttle Control Motor Circuit. P2107 - Electronic Throttle Control Module Processor.

JEEP · 2022-10-19

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTC: P152E - Engine Hood Switch 2 Circuit High. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. P0032 - O2 Sensor 1/1 Heater Circuit High. P0038 - O2 Sensor 1/2 Heater Circuit High. P0052 - O2 Sensor 2/1 Heater Circuit High. P0058 - O2 Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High. P2100 - Electronic Throttle Control Motor Circuit. P0300 - Multiple Cylinder Misfire. In addition,…

JEEP · 2022-10-11

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following (Diagnostic trouble Codes (DTCs): P0032 - O2-Sensor 1/1 Heater Circuit High. P0038 - O2-Sensor 1/2 Heater Circuit High. P0052 - O2-Sensor 2/1 Heater Circuit High. P0058 - O2-Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High. P2100 - Electronic Throttle Control Motor Circuit. P2107 - Electronic Throttle Control Module Processor.

JEEP · 2022-07-15

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following (Diagnostic trouble Codes (DTCs): P0032 - O2-Sensor 1/1 Heater Circuit High. P0038 - O2-Sensor 1/2 Heater Circuit High. P0052 - O2-Sensor 2/1 Heater Circuit High. P0058 - O2-Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High. P2100 - Electronic Throttle Control Motor Circuit.P2107 - Electronic Throttle Control Module Processor.

FORD · 2021-07-19

Some 2020 F-Super Duty vehicles equipped with a 6.2L or 7.3L engine, 10R140 transmission, and built on or before 05-Jun-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0132, P0135, P0138, P0141, P0152, P0155, P0158 and/or P0161 stored in the powertrain control module (PCM). This may be due to water intrusion into heated oxygen sensor (HO2S) connectors C141, C142, C1571 and/or C1572 on the transmission harness where it connects to the engine exhaust sensors. To correct the condition, follow the Service Procedure steps to replace the transmission harness and the affected heated oxygen sensors (HO2S) and/or the catalyst monitor sensor.

FORD · 2020-10-30

Some 2020 F-Super Duty vehicles equipped with the 6.2L or 7.3L engine built on or before 05-Jun-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0132, P0135, P0138, P0141, P0152, P0155, P0158 and/or P0161 stored in the powertrain control module (PCM). This may be due to water intrusion into heated oxygen sensor (HO2S) connectors C141, C142, C1571 and/or C1572 on the transmission harness where it connects to the engine exhaust sensors. To correct the condition, follow the Service Procedure steps to replace the transmission harness and the affected heated oxygen sensors (HO2S) and/or the catalyst monitor sensor.

CADILLAC, CHEVROLET, GMC · 2019-05-07

This Preliminary information communicates Check Engine Light on and vehicle runs rough. This condidtion will occur within the first 5 minutes after the vehicle is started. his condition may be caused by a software anomaly that allows all four DTC's P0132, P0137, P0152, P0157 to set. All 4 DTCs must be in history for this PI to apply.

INFINITI · 2015-12-01

IF YOU CONFIRM: The MIL is ON with one or more of the following DTCs stored: Bank 1 - P2096, P2097 --- POST CAT FUEL TRIM SYS B1 - P0130, P0131, P0132 --- A/F SENSOR1 (B1) - P0031, P0032 --- A/F SEN1 HTR (B1) - P014C, P014D, P015A, P015B --- Air fuel ratio (A/F) sensor 1 (bank 1) Bank 2 - P2098, P2099 --- POST CAT FUEL TRIM SYS B2 - P0150, P0151, P0152 --- A/F SENSOR1 (B2) - P0051, P0052 --- A/F SEN1 HTR (B2) - P014E, P014F, P015C, P015D --- Air fuel ratio (A/F) sensor 1 (bank 2) ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm ECM reprogramming applies. 2. If reprogramming applies, reprogram the ECM. 3. Replace only the A/F sensors related to the stored DTCs. - If stored DTCs are for only one bank, replace only one A/F sensor for that bank. - If stored DTCs are for both…

LAND ROVER · 2015-10-15

"ISSUE: THE CUSTOMER MAY OBSERVE A MIL IN THE INSTRUMENT CLUSTER RELATING TO THE ENGINE SYSTEM (CHECK ENGINE LIGHT) AND ONE OR MORE CODES STORED IN THE PCM RELATING TO HEATED OXYGEN SENSOR (HO2S) IN THE EXHAUST SYSTEM. THE CODE WILL REFER TO A FAULT WITH THE PRE, OR MID, OR POST CATALYST HEATED OXYGEN SENSOR: P0030, P0031, P00D1, P0130, P0131, P0132, P0133, P0134, P0135, P014C, P2195, P2196, P2231, P2237, P2243, P2245, P2251, P2297, P2626, P2A00, P0050, P0051, P00D3, P0150, P0151, P0152, P0153, P0154, P0155, P2197, P2198, P2234, P2240, P2247, P2254, P0037, P0038, P0054, P0136, P0137, P0138, P0139, P013A, P013E, P0140, P0141, P2270, P2271, P0056, P0057, P0060, P013C, P014A, P0156, P0157, P0158, P0159, P0160, P0161, P2272, P2273, P0042, P0043, P0044, P0055, P0142, P0143, P0144, P0147,…

CHRYSLER · 2006-04-06

DTC'S P2152, P0152, P0154, P0151, P0089, P0091 AND P0092 ARE BEING INCORRECTLY REPORTED FOR P2149, P0132, P0131, P0087, AND P0088. *TT