P061B · Communications du constructeur

RAM · 2020-02-26

PEDAL, Accelerator (APPS) Before replacing accelerator pedal for P061B, make sure all PCM software service bulletins and recalls are up to date, if applicable. Before replacing accelerator pedal for other DTCs, be sure to follow fault code diagnostic procedures in Service Library and be sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and acceleartor pedal should not be replaced for this fault if driving style is confirmed with the customer.

LAND ROVER · 2019-10-28

The Malfunction Indicator Lamp (MIL) is illuminated on the Instrument Panel Cluster (IPC), with reduced performance experienced while driving. Further investigation has found that Diagnostic Trouble Code(s) (DTC) P061B-22 is stored in the Powertrain Control Module (PCM).

MAZDA · 2019-08-12

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

MAZDA · 2019-05-13

Some vehicles may display some (or all) of the following symptoms: Check engine light on wit DTC P061B Surging on acceleration Transmission will not shift past 4th gear Various U codes (U0401 ABS, U0401, U0415 FSC, U0301, U0316 SBS/MRCC, U0442 TCM) may be set

MAZDA · 2019-05-02

Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem This concern may be caused by improper PCM control logic. The engine torque calculation error may increase in high temperatures at high elevations. To eliminate this concern, the PCM software has been modified.

FORD · 2019-03-25

Some 2015-2018 Transit vehicles built on or before 24-Jul-2018 may exhibit various drivability concerns including difficulty starting, misfires and/or an illuminated MIL with diagnostic trouble codes (DTCs) P00BD, P1247, P1548, P061B, P2195, P2198, P2196, P2197, P0171, P0172, P0174, P0175, P0131 and/or P162F stored in the powertrain control module (PCM). This may be due to undesired water entry into the engine compartment directly over powertrain components. To resolve this condition, install updated water management hardware and/or a revised air cleaner cover.

MAZDA · 2019-03-22

Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem.This concern may be caused by improper PCM control logic. The engine torque calculation error may increase in high temperatures at high elevations. To eliminate this concern, the PCM software has been modified.

MAZDA · 2019-02-28

Some vehicles may display some (or all) of the following symptoms: Check engine light on wit DTC P061B, Surging on acceleration, Transmission will not shift past 4th gear, Various U codes (U0401 ABS, U0401, U0415 FSC, U0301, U0316 SBS/MRCC, U0442 TCM) may be set.

FORD · 2018-11-21

Some 2018 EcoSport vehicles equipped with a 1.5L Duratorq-TDCi engine may exhibit an illuminated MIL with DTC P061B. The 2018 Powertrain Controls/Emission Diagnosis (PC/ED) Diesel Manual, Section 4 is incorrect and a powertrain control module (PCM) replacement may not be necessary for this DTC. The PC/ED is in the process of being updated. Do not replace the PCM at this time. Engineering is investigating, monitor OASIS for updates.

FORD · 2018-10-23

Some 2015-2018 Transit vehicles built on or before 24-Jul-2018 may exhibit various drivability concerns including difficulty starting, misfires and/or an illuminated MIL with diagnostic trouble codes (DTCs) P00BD, P1247, P1548, P061B, P2195, P2198, P2196, P2197, P0171, P0172, P0174, P0175, P0131 and/or P162F stored in the powertrain control module (PCM). This may be due to undesired water entry into the engine compartment directly over powertrain components. Follow the Service Procedure steps to correct the condition.

MAZDA · 2018-10-23

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 and U0401:00 stored in the PCM memory when engine cranking is interrupted and on A/T vehicles, DTC U0442:00 is also stored. This concern most likely occurs when the brake pedal is released during engine cranking. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. DTC U0401:00 - Signal error from PCM DTC U0442:00 - [TCM] Invalid data received from PCM. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

MAZDA · 2018-10-22

Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. This concern may be caused by improper PCM control logic. The engine torque calculation error may increase in high temperatures at high elevations. To eliminate this concern, the PCM software has been modified.

MAZDA · 2018-08-24

Some vehicles may experience a check engine light on and/or failsafe with DTC P061B:00 stored in the PCM. This condition will likely occur as a result of one of the following causes: Engine cranking was interrupted by releasing the brake pedal. Start button was double pressed while the engine was still cranking. A countermeasure to correct mis-detection is currently being prepared.

MAZDA · 2018-08-22

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in the PCM memory when engine cranking is interrupted. This concern most likely occurs when the brake pedal is released during engine cranking. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

FORD · 2018-06-20

Some 2018 F-150 vehicles equipped with a 3.0L diesel engine may have DTC P061B set in the powertrain control module (PCM) after scan tool requested engine speed control. This may include engine speed output state control in data logger, key on engine running (KOER) self-test, or a manual diesel particulate filter (DPF) regeneration where engine speed is increased during the regeneration. Disregard this DTC. Engineering is aware of this concern. Monitor OASIS for updates.

MAZDA · 2018-02-28

Some vehicles may experience a check engine light on and/or failsafe with DTC P061B:00 stored in the PCM. This condition will likely occur as a result of one of the following causes: Engine cranking was interrupted by releasing the brake pedal. Start button was double pressed while the engine was still cranking. A countermeasure to correct mis-detection is currently being prepared.

FIAT, JEEP · 2017-09-14

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P0887 - TCM Power Control Circuit High. P061B - Internal Control Module Torque Calculation Performance. P072F - Stuck In Fourth Gear. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance(2015 BU Only). P1CC9 - Unable to Engage Gear(2015 BU Only). P1D98 - Incorrect Gear Ratio Clutch B or D Defective(2015 BU Only). U0401 - Implausible Data Received From ECM-PCM(2015 BU Only). In addition, customers may notice the following condition(s):Harsh 1-2…

CHRYSLER, JEEP · 2017-09-09

Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) withthe latest available software.A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination and/or one of the following conditions. Uponfurther investigation, a technician may find one or more of the following DTCs stored in the TCM memory.2015 KL VehiclesP1634-00 - TCM Internal Watchdog Performance(Sales Codes ED6 or ED8 Only).U1412- Implausible Vehicle Speed Signal Received. U0001- Can C Bus. P0887-00- TCM Power Control Circuit High. P061B-00- Internal Control Module Torque Calculation Performance. U0401-00- Implausible Data Received From ECM/PCM. P1DAD-00- Input Shaft-Output Shaft Direction Correlation. P0711-00- Transmission…

CHRYSLER · 2017-08-05

Flash: Hybrid Control Processor (HCP) and the Auxiliary Hybrid Control Processer (AHCP) This bulletin involves a combination reprogramming of the HCP and the AHCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following DTCs have been set:P0A79-00 - Drive Motor B Inverter Performance. The software has been updated to better address this DTC. P0A78-00 - Drive A Inverter Performance. U0415-00 - Implausible Data Received From ABS. P0A3F-00 - Drive Motor A Position Sensor 1 Circuit. P061B-00 - Internal Control Module Torque Calculation Performance. P26C3-00 - Internal Control Module Electronic Shifter Performance.

MAZDA · 2017-07-12

Some 2012-2016 Mazda3s, 2013-2015 CX-5s and 2014-2015 Mazda6s may experience the Check Engine Light ON with DTC P0101 and/or P061B and/or driveability problem after reprogramming the PCM using IDS versions 105.02 to 105.04. If the PCM is reprogrammed with any software number included in the attached file and the throttle valve has too much carbon build up, the engine air amount calculation by the problem software may not be accurate. Perform the following Repair Procedure to correct this issue. NOTE Current version of IDS is 106.02.

CHRYSLER · 2017-06-17

Flash: Hybrid Control Processor (HCP) and the Auxiliary Hybrid Control Processer (AHCP) This bulletin involves a combination reprogramming of the HCP and the AHCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0A79-00 - Drive Motor B Inverter Performance. U0415-00 - Implausible Data Received From ABS. P0A3F-00 - Drive Motor A Position Sensor 1 Circuit. P061B-00 - Internal Control Module Torque Calculation Performance. P26C3-00 - Internal Control Module Electronic Shifter Performance.

FORD · 2017-02-15

SOME 2015 TRANSIT VEHICLES BUILT ON OR BEFORE 30-MAR-2015 MAY EXHIBIT VARIOUS DRIVABILITY CONCERNS INCLUDING DIFFICULTY STARTING, MISFIRES AND/OR AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODE (DTC) P00BD, P1247, P1548, P061B, P2195, P2198, P2196, P2197, P0171, P0172, P0174, P0175, P0131 AND/OR P162F STORED IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY. THIS MAY BE DUE TO UNDESIRED WATER ENTRY INTO THE ENGINE COMPARTMENT DIRECTLY OVER POWERTRAIN COMPONENTS. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

MAZDA · 2017-01-13

Check engine light (with DTCs P0101, P061B, P2122, P2138) may illuminate after PCM reprogramming due to a mislogic detection in the PCM calibration, available in the current IDs version 103.03. Please uninstall IDS and install version 103.00 to prevent this situation and "do not update ids until further notice"

JEEP · 2016-11-11

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one of the following Diagnostic Trouble Code (DTCs) stored in the TCM memory: P061B-00 - Internal Control Module Torque Calculation Performance. P072F-00 - Stuck In Gear 4.The following enhancements are included in the software update: Transmission shift quality enhancement in conjunction with Powertrain Control Module (PCM) reprogram. 7-8 gear increase shift at higher speed. 8-9 gear shift will happen on a downhill only. Coast down bump on 7-6, 6-5, 5-4, 5-3 downshift improvements. Cold 1-2, 2-3…

FIAT, JEEP · 2016-09-21

Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the TCM memory: P061B - Internal Control Module Torque Calculation Performance. P072F - Stuck In Gear 4. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (2015 BU only). P0887 - TCM Power Control Circuit High (2015 BU only). P1CC9 - Unable to Engage Gear (2015 BU only). P1D98 - Incorrect Gear Ratio Clutch B or D Defective (2015 BU only). U0401 - Implausible Data Received From ECM-PCM (2015 BU only).In addition, customers may experience…

JEEP · 2016-08-06

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory: · P061B-00 - Internal Control Module Torque Calculation Performance. · P072F-00 - Stuck In Gear 4. The following enhancements are included in the software update: · **7-8 gear increase shift at higher speed. · 8-9 gear shift will happen on a downhill only.** · Coast down bump on 7-6, 6-5, 5-4, 5-3 downshift improvements. · Cold 1-2, 2-3 upshift improvements. · 1-2, 2-3 upshift flare control improvements. · Power-on upshift…

JEEP · 2016-08-06

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory: · P061B-00 - Internal Control Module Torque Calculation Performance. · P072F-00 - Stuck In Gear 4. The following enhancements are included in the software update: · **7-8 gear increase shift at higher speed. · 8-9 gear shift will happen on a downhill only.** · Coast down bump on 7-6, 6-5, 5-4, 5-3 downshift improvements. · Cold 1-2, 2-3 upshift improvements. · 1-2, 2-3 upshift flare control improvements. · Power-on upshift…

JEEP · 2016-06-04

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · **P061B-00 - Internal Control Module Torque Calculation Performance. · P072F-00 - Stuck In Gear 4.** · P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. · P1DAD - Input Shaft-Output Shaft Direction Correlation. · P1CC9 - Unable to Engage Gear. · P1D98 - Incorrect Gear Ratio Clutch B or D Defective. · U1424 - Implausible Engine Torque Signal Received. In addition to correcting the DTCs listed this…

JEEP · 2016-06-04

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. **Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory: · P061B-00 - Internal Control Module Torque Calculation Performance. · P072F-00 - Stuck In Gear 4. The following enhancements are included in the software update: · Coast down bump on 7-6, 6-5, 5-4, 5-3 downshift improvements. · Cold 1-2, 2-3 upshift improvements. · 1-2, 2-3 upshift flare control improvements. · Power-on upshift improvements. · Lift Foot Upshift 2-3, 4-5, 8-9 improvements.** · Improve transmission shift…

JEEP · 2016-06-04

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · **P061B-00 - Internal Control Module Torque Calculation Performance. · P072F-00 - Stuck In Gear 4.** · P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. · P1DAD - Input Shaft-Output Shaft Direction Correlation. · P1CC9 - Unable to Engage Gear. · P1D98 - Incorrect Gear Ratio Clutch B or D Defective. · U1424 - Implausible Engine Torque Signal Received. In addition to correcting the DTCs listed this…