P1404 · Communications du constructeur

MERCEDES-BENZ · 2026-02-03

Complaint Check engine light illuminate, or previously on One of the below Exhaust Flap fault codes stored in PTCU N127: P13C273 P13C278 P140473 Cause Various Remedy Model year 2024 254 and 167 with engine M254 -Update software of N127 PTCU. New software: 254- A2549022611 167- A2549022811 -Clear fault codes and check operation of the exhaust flap. Models with M256, or models with M254 after SW update -Check exhaust flap for free movement via actuation. -Remove flap actuator and check movement of flap in exhaust pipe. Replace exhaust pipe section if flap is binding. -Replace flap actuator if above checks are ok. If fault code returns after performing the above steps, open a TIPS case with the powertrain team. Note: Codes P13C273 and P13C278- Right side flap Code P140473- Left side flap

RAM · 2026-01-27

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1404 - EGR Close Position Performance. Customers may also comment on one or more of the following: ● Engine tugging. ● Unstable idle. This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.

RAM · 2025-04-03

"Heavy Duty Exhaust Gas Recirculation (EGR) Value Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P1404 - EGR Position Sensor Rationality Closed This bulletin involves replacing the EGR valve."

RAM · 2024-07-24

"Heavy Duty Exhaust Gas Recirculation (EGR) Valve Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1404 - EGR Position Sensor Rationality Closed This bulletin involves replacing the EGR valve."

RAM · 2023-06-03

Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P1404 - EGR Close Position Performance. ? P0456 - EVAP System Small Leak. NOTE: If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. In addition, the customer may notice one or more of the following conditions: ? **Power Take Off (PTO) disable to high engine oil temperature (DD DP Only).** ? Abrupt gear engagement when transitioning from Park to Drive/Reverse gear state in Power Takeoff (PTO) Mode. ? Vehicle hesitation or surge at low vehicle speeds. ? Engine…

RAM · 2023-05-26

Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P1404 - EGR Position Sensor Rationality Closed. ? P2457 - Exhaust Gas Recirculation Cooling System Performance. NOTE: P1404 - EGR Position Sensor Rationality Closed DTC can be erroneously set when P2457 -Exhaust Gas Recirculation Cooling System Performance DTC is set. In addition, the customer may notice one or more of the following conditions: ? **Power Take Off (PTO) disable to high engine oil temperature (DD DP with DF3 Only).** ? In PTO mode, transmission gear engagement is abrupt and idle speed is high when transitioning From Park To…

JEEP · 2022-05-11

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire. If DTC P0300 is present either alone or along with other DTCs listed within thisbulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right.If just the software flash was done without the right intake camshaft being replacedthe DTC…

RAM · 2022-04-28

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the correct software. This vehiclemay have been programmed with incorrect software. The customer may experience Active Noise Control (ANC) system not working. Upon further investigation the technician may find the followingDTCs have been set: P1404 - EGR Position Sensor Rationality Closed. B154F-64 - Lost Crankshaft Pulse Signal-Signal Plausibility Failure B154F-24 - Lost Crankshaft Pulse Signal-Signal Stuck High. P1404 - EGR Position Sensor Rationality Closed DTC can be erroneously set when other DTCs are set.In addition, customers may experience one or more of the following concerns: In Power Take-Off (PTO) mode, transmission gear engagement is abruptand idle speed is high when transitioning…

RAM · 2022-04-28

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DiagnosticTrouble Code (DTC) has been set: P1404 - EGR Position Sensor Rationality Closed. In addition, customers may experience one or more of the following concerns: In Power Take-Off (PTO) mode, transmission gear engagement is abrupt and idle speedis high when transitioning From Park To Drive/Reverse Gear.

RAM · 2022-04-28

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set: P1404 - EGR Position Sensor Rationality Closed. P2457 - Exhaust Gas Recirculation Cooling System Performance. P1404 - EGR Position Sensor Rationality Closed DTC can be erroneously set when P2457 - Exhaust Gas Recirculation Cooling System Performance DTC is set.In addition, customers may experience one or more of the following concerns: In Power Take-Off (PTO) mode, transmission gear engagement is abruptand idle speed is high when transitioning From Park To Drive/Reverse Gear.

JEEP · 2022-03-09

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within thisbulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replacedthe DTC…

JEEP · 2022-03-08

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within thisbulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replacedthe DTC…

JEEP · 2022-03-08

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within this bulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replacedthe DTC…

JEEP · 2021-03-06

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within this bulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake…

JEEP · 2021-03-06

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within this bulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake…

JEEP · 2020-09-30

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following Diagnostic Trouble Codes (DTCs).P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before…

JEEP · 2020-08-28

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs.P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the…

JEEP · 2020-08-28

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs.P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the…

JEEP · 2020-07-11

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs.P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the…

JEEP · 2020-07-11

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs.P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the…

JEEP · 2019-11-19

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs.P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT)to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the…

JEEP · 2019-11-19

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs.P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT)to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the…

FCA · 2018-04-17

Cooled EGR Assembly This Tech Tip applies to Ram DJ, D2, DD trucks for 2014 and 2015 model years equipped with the 6.4 ESA and 6.4 ESB HEMI Heavy Duty engines. Please contact engineering prior to replacing any components if the vehicle has a P1404, P0404, P0405, or P0406 DTC code. Engineering would like to collect freeze frame data on units with these DTC codes. Please contact Russ Craig on cell (248) 420-5675. If no response in 15 minutes, proceed with repair.

RAM · 2017-06-24

Flash: 6.4L Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. This bulletin fixes all vehicles listed and also contains an optional software path for situations where the customer is specifically complaining of a drone noise, shudder, pulsation, or vibration under light throttle applications, while vehicle is operating in Multi Displacement System/Economics (MDS/ECO)mode (optional software available for D2&DJ vehicles).There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?MDS NOISE?. The other file is the standard software that does not contain improvements for the drone/shudder concern. If…

RAM · 2017-06-24

Flash: 6.4L Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. This bulletin fixes all vehicles listed and also contains an optional software path for situations where the customer is specifically complaining of a drone noise, shudder, pulsation, or vibration under light throttle applications, while vehicle is operating in Multi Displacement System/Economics (MDS/ECO)mode (optional software available for D2&DJ vehicles).There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage MDS NOISE. The other file is the standard software that does not contain improvements for the drone/shudder concern. If for…

CHEVROLET, PONTIAC · 2007-03-01

LNJ SERVICE ENGINE SOON (SES) LIGHT ILLUMINATED, MULTIPLE POWERTRAIN CONTROL MODULE (PCM) DIAGNOSTIC TROUBLE CODE (DTC) P1404 AND/OR P0404. *TT UPDATED 04-27-07. *KB

CHEVROLET, PONTIAC · 2007-03-01

SERVICE ENGINE SOON (SES) LIGHT ILLUMINATED, MULTIPLE POWERTRAIN CONTROL MODULE (PCM) DIAGNOSTIC TROUBLE CODE (DTC) P1404 AND/OR P0404. 06-06-04-002 NOT YET RECEIVED. *TT UPDATED 04-27-07. *KB

BUICK, CHEVROLET, PONTIAC, SATURN · 2007-03-01

SERVICE ENGINE SOON (SES) LIGHT ILLUMINATED, MULTIPLE POWERTRAIN CONTROL MODULE (PCM) DIAGNOSTIC TROUBLE CODE (DTC) P1404 AND/OR P0404. 06-06-04-003 NOT YET RECEIVED. *TT UPDATED 04-27-07. *KB

BUICK, CHEVROLET, OLDSMOBILE, PONTIAC · 2002-09-01

INTERMITTENT MALFUNCTION INDICATOR LAMP (MIL) AND POWER TRAIN CONTROL MODULE (PCM) DIAGNOSTIC TROUBLE CODE (DTC) P1404. *TT

CHEVROLET, FORD, GMC, OLDSMOBILE · 1998-09-01

SUBJECT REGARDING OBD II DIAGNOSTIC TROUBLE CODE (DTC) P1404 (REFLASH VCM). *YC