U0212 · Communications du constructeur

JEEP · 2025-09-27

Not applicable to vehicles built for US market. Multiple Systems Repair Bundle Campaign Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U11E3-00 - TCM Lost Communication With ESM On DPT CAN. ● B15A1-00 - Media Port 1 Connection. ● U11C2 - Lost Transmission Message. ● U11E4-00 - CAN Communication Messages Missing. ● U120C - Lost Brake Booster Signal. ● U1216-00 - Lost Communication With DASM. ● U121E-00 - Lost Communication With Steering Wheel Cruise Control Switch. ● U1267-00 - No Valid Data From ESM On CAN-C Or CAN-DPT. ● U12A8 - Lost Communication With Master Cylinder Pressure Sensor. ● U1465-00 - Implausible Driver Shift Request Signal Received. ● U1466-00-…

CHRYSLER · 2024-11-19

SWITCH Multifunction Before replacing the steering column control module (SCCM) due to DTC U0212 active, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps at BCM. 2.- If failure still present, make sure all the switches' and airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from wipers is requested, if turn signal, blindspot and lane assistant work. 5.- Do a hard reset to BCM and evaluate…

ISUZU · 2022-06-17

Dealers, upfitters or bodybuilders may notice various warning lights on the dash illuminating and certain DTCs without an apparent cause during the initial installation and connection of telematics, GPS, and/or other aftermarket devices to the FMS system on certain 2022MY vehicles equipped with RPO I4H, DTCs that may occur are P1381, P1382, U2105, U1001, U0140, U0101, U0100, U0212, U0219, and U0028. These vehicles were configured with an incorrect module setup during the FMS installation at the port, which causes these lights and codes to set. Follow the service procedure below to validate that this incorrect configuration is the cause of these lights and codes and to reconfigure the Controller Area Network (CAN) Bus Interface.

CADILLAC, CHEVROLET, GMC · 2021-08-06

This informational bulletin provides information for dealers/technicians on the false setting of DTC U0212.

CADILLAC, CHEVROLET, GMC · 2020-12-07

This informational bulletin provides information for dealers/technicians on the false setting of DTC U0212.

CADILLAC · 2020-05-26

This informational bulletin provides information for dealers/technicians on the false setting of DTC U0212.

AUDI · 2014-03-31

Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635,…