P00C6 · メーカー技術情報

JAGUAR · 2015-04-08

"SITUATION: THE ENGINE MALFUNCTION INDICATOR LAMP (MIL) MAY BE ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTC) P00C6 AND P228D-00 OR P228C-77 STORED IN THE ENGINE CONTROL MODULE (ECM). ADDITIONALLY, THE ENGINE MAY EXPERIENCE ROUGH RUNNING, HARD STARTING, A ROUGH IDLE, OR MISFIRES AND ONE OR MORE MISFIRE DTCS (P0300, P0301, P0302, P0303, P0304, AND/OR P1315) STORED IN THE ECM. CAUSE: THIS MAY BE CAUSED BY AN INTERNAL FAULT WITH THE METERING VALVE IN THE HIGH PRESSURE FUEL PUMP."

BUICK, CADILLAC, CHEVROLET, GMC · 2014-12-17

This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.

CHEVROLET, GMC · 2014-08-19

This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.

BUICK, CADILLAC, CHEVROLET, GMC · 2014-08-18

This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.

CHEVROLET, GMC · 2014-08-01

GM: ENGINE WILL CRANK BUT WILL NOT START. DTC P00C6 MAY BE SET. LOW FUEL RAIL PRESSURE. ALSO INCLUDES CHEVROLET CORVETTE, GMC YUKON XL AND SIERRA. MODEL YEAR 2015. *JS UPDATED 05/19/2014 *JS UPDATED 11/12/14. *PE

BUICK, CADILLAC, CHEVROLET · 2014-06-27

This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.

CHEVROLET, GMC · 2014-04-30

This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicles with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. If the vehicle is a crank no start, perform PIE0295.

CHEVROLET, GMC · 2014-03-31

This Preliminary Information communication provides information to the technician how to diagnose and repair vehicles with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. Technician will need to use Global Diagnostic System 2 to actuate the cam phaser solenoid 4 or 5 times then try starting the vehicle. Then disable the ignition and fuel system. After the ignition and fuel system are disabled try to start the engine. Technician can now unplug the camshaft actuator to perform the following. Install a 20A fused jumper wire between the terminal 2 and 12V. Tickle/tap the low reference terminal 1 to ground on the cam actuator magnet, while cranking the engine over. When the engine starts and runs the cam actuator or oil…

CHEVROLET, GMC · 2014-03-03

This Preliminary Information communication provides information to the technician how to diagnose and repair vehicles with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. Technician will need to use Global Diagnostic System 2 to actuate the cam phaser solenoid 4 or 5 times then try starting the vehicle. Then disable the ignition and fuel system. After the ignition and fuel system are disabled try to start the engine. Technician can now unplug the camshaft actuator to perform the following. Install a 20A fused jumper wire between the terminal 2 and 12V. Tickle/tap the low reference terminal 1 to ground on the cam actuator magnet, while cranking the engine over. When the engine starts and runs the cam actuator or oil…

CHEVROLET, GMC · 2013-11-22

This Preliminary Information communication provides information to the technician how to diagnose and repair vehicles with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. Technician will need to use Global Diagnostic System 2 to actuate the cam phaser solenoid 4 or 5 times then try starting the vehicle. Then disable the ignition and fuel system. After the ignition and fuel system are disabled try to start the engine. Technician can now unplug the camshaft actuator to perform the following. Install a 20A fused jumper wire between the terminal 2 and 12V. Tickle/tap the low reference terminal 1 to ground on the cam actuator magnet, while cranking the engine over. This may have to be performed more than once.

CHEVROLET, GMC · 2013-06-14

This Preliminary Information communication provides information to the technician how to diagnose and repair vehicles with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. Technician will need to use Global Diagnostic System 2 to actuate the cam phaser solenoid 4 or 5 times then try starting the vehicle. Then disable the ignition and fuel system. After the ignition and fuel system are disabled try to start the engine. Technician can now unplug the camshaft actuator to perform the following. Install a 20A fused jumper wire between the terminal 2 and 12V. Tickle/tap the low reference terminal 1 to ground on the cam actuator magnet, while cranking the engine over. This may have to be performed more than once.