Skip to content

P061A · Manufacturer communications

A listed vehicle is a research lead. Confirm the engine, production range and software in the manufacturer's information.

P061A ← What does this code mean?

69 Results

18-034-19 REV. A ↗

JEEP · 2019-12-04

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs:P061A - Level 2 Torque Performance. P0507 - Idle Speed Performance Higher Than Expected. P0456 - EVAP System Small Leak. Customers may also describe the following condition:Excessive fan noise when the A/C is on MAX output. Other enhancements included in this update:Electric vacuum pump (EVP) update. Fan noise reduction.

TSB 18-2326 ↗

FORD · 2018-10-23

Some 2018 F-150 vehicles equipped with a 3.0L diesel engine built on or before 10-Oct-2018 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P06EA, P0315a, P20EE, P0401, P2201, P0106, P0191 and/or P061A stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.

TIN1813003 ↗

MITSUBISHI · 2018-10-03

This is a Technical Information Notice sent to dealers. It informs dealers that a new Engine ECU software update (Software Part Number 1860D11603) was made available on June 7, 2018 that addresses both MFI Diagnostic Trouble Codes (DTCs) P0068 and P061A. Dealers are to perform the Engine ECU reprogramming procedure outlined in TSB-18-13-001 and TSB-18-13-002, on any new or used affected vehicles in the inventory or that visit the dealership service department. Dealers are recommended to reprogram the Engine ECU when an affected vehicle is brought in to have SR-18-007 (FCM-ECU Reprogramming) and/or SR-18-008 (ASC Hydraulic Unit ECU Reprogramming) completed.

TSB-18-13-002 ↗

MITSUBISHI · 2018-06-07

This is a Technical Service Bulletin sent to dealers. It instructs dealers to reprogram the engine ECU with updated software to correct the issue, on certain vehicles, of MIL illumination with DTC P061A. During turbocharged driving, DTC P061A (Torque Monitoring) may set when the current monitor does not recognize turbocharged operation. When DTC P061A is detected, the vehicle goes into fail-safe mode and vehicle speed is restricted to a maximum of 25 mph (40 km/h). Depending on vehicle and/or driving conditions, DTC P1574, C1707, C121C, C1777, or C2339 may also be detected. The new ECU software optimizes the Torque Monitoring to be able to recognize turbocharged operation.

TIN-18-13-002 ↗

MITSUBISHI · 2018-06-07

This is a Technical Information Notice sent to dealers, informing them that an update will be available to address MFI DTCs P0068 and P061A that have been improperly set. Dealers are asked to check the software part number as described in TSB-18-13-001 and TSB 18-13-002 when reprogramming the Engine ECU.

SSM 47097 ↗

FORD · 2018-02-21

Some 2017-2018 F-150 vehicles built on or before 29-Sep-2017 may exhibit a no crank/no start, auto-start-stop inoperative, illuminated malfunction indicator lamp (MIL) and or powertrain malfunction indicator lamp, transmission shift issues, DTC P061A, U0140, U0401, U0101, U0074 and/or U0037 being set in the PCM, TCM, IPC, FCIM, ABS and/or PSCM. This may be due to the 15525 transmission wire harness not being properly secured. Visually inspect the harness for possible damage and proper routing at the rear of the engine down to the transmission. Repair as necessary. If no damage is found, proceed with normal diagnostics.

18-023-16 REV. C ↗

CHRYSLER, DODGE · 2016-06-21

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 -…

18-023-16 REV.C ↗

CHRYSLER, DODGE · 2016-06-21

FLASH: 2.4L POWERTRAIN DIAGNOSTIC AND SYSTEM IMPROVEMENTS. BULLETIN INVOLVES REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH THE LATEST AVAILABLE SOFTWARE. A SMALL NUMBER OF CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION OR ONE OR MORE OF THE FOLLOWING CONDITIONS. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTCS) SET IN THE PCM, MEMORY:2015 UF VEHICLES WITH (SALES CODES ED6, ED8)· P050D - COLD START ROUGH IDLE. P0335 - CRANKSHAFT POSITION SENSOR CIRCUIT. P1607 - PCM INTERNAL SHUTDOWN TIMER RATIONALITY. P0133 - O2 SENSOR 1/1 SLOW RESPONSE. P0456 - EVAP SYSTEM SMALL LEAK.· P0480 - COOLING FAN 1 CONTROL CIRCUIT/OPEN. U0402 - IMPLAUSIBLE DATA RECEIVED FROM TCM. P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED.P1D73 - AGS…

18-023-16 ↗

CHRYSLER, DODGE · 2016-06-02

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - EVAP System Small Leak. · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak…

18-023-16 REV. B ↗

CHRYSLER, DODGE · 2016-06-02

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 -…

1802316REVA ↗

CHRYSLER, DODGE · 2016-05-18

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · **P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak.** · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum…

18-023-16 REV. A ↗

CHRYSLER, DODGE · 2016-05-18

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · **P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak.** · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum…

18-009-15 REV G ↗

DODGE · 2015-12-18

Flash: 1.4L Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2016 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. 2015 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1046 - Cylinder 1 Oil Supply Solenoid…

18-010-15 REV. D ↗

FIAT · 2015-10-08

Flash: 1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? Cranks fast, as if no compression. ? P1524 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled (2014 Vehicles only). ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream (2014 Vehicles only). ? P0141 - Oxygen Sensor 1/2 Heater Performance (2015 Vehicles only). ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent.…

18-010-15 REV-D ↗

FIAT · 2015-10-08

Flash: 1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? Cranks fast, as if no compression. ? P1524 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled (2014 Vehicles only). ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream (2014 Vehicles only). ? P0141 - Oxygen Sensor 1/2 Heater Performance (2015 Vehicles only). ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent.…

18-009-15 REV-F ↗

DODGE · 2015-09-19

Flash: 1.4L Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2016 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. 2015 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1046 - Cylinder 1 Oil Supply Solenoid…

18-009-15 REV-E ↗

DODGE · 2015-09-01

Flash: 1.4L Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2014 Dart ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream. ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? DTC P061A - Level 2…

18-009-15 REV-D ↗

DODGE · 2015-08-27

Flash: 1.4L Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2014 Dart ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream. ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? DTC P061A - Level 2…

18-010-15 REV-C ↗

FIAT · 2015-08-27

Flash:1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P0141 Oxygen Sensor 1/2 Heater Performance (software has been updated to better address this DTC, for EAB engines). ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P061A Internal Control Module Torque Performance (2014 Vehicles only). ? Improved reverse lamp…

18-009-15 REV-C ↗

DODGE · 2015-08-04

Flash: 1.4L MIL Illumination. Includes Various Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1…

18-010-15 REVB ↗

FIAT · 2015-07-30

Flash:1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Codes (DTCs): ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P0141 Oxygen Sensor 1/2 Heater Performance. ? P061A Internal Control Module Torque Performance (2014 Vehicles only). ? Improved reverse lamp activation time (2015 auto trans only). ? Improved cold weather starting, below -4 °F (-20 °C).

18-009-15 REVB ↗

DODGE · 2015-07-23

Flash: MIL Illumination. Includes Various Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response (2015 only). ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? DTC P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant…

18-010-15 REVA ↗

FIAT · 2015-04-13

Flash:1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Codes (DTCs): ? P0141 Oxygen Sensor 1/2 Heater Performance. ? P061A Internal Control Module Torque Performance (2014 Vehicles only). ? Improved reverse lamp activation time (2015 auto trans only). ? Improved cold weather starting, below -4 °F (-20 °C).

18-009-15 REV. A ↗

DODGE · 2015-03-24

Flash: MIL Illumination. Includes Various Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response (2015 only). ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? DTC P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using…

18-010-15 ↗

FIAT · 2015-01-23

Flash:1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Codes (DTCs): ? P0141 Oxygen Sensor 1/2 Heater Performance. ? P061A Internal Control Module Torque Performance (2014 Vehicles only). ? Improved reverse lamp activation time (2015 auto trans only).

18-069-14 ↗

FIAT · 2014-11-26

Flash: MIL Illumination, P0141 Oxygen Sensor 1/2 Heater Performance, P061A Internal Control Module Torque Performance This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P0141 Oxygen Sensor 1/2 Heater Performance and/or P061A Internal Control Module Torque Performance.

18-062-14 ↗

RAM · 2014-11-14

Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L Turbo Diesel. These improvements are separated into the following categories.Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTCs). These DTCs Are Currently Set As A One Trip Fault And Should Be A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeded Learning Limit.These DTCs Are Currently Set As A Two Trip Fault And Should Have Been A One Trip Fault: U12A4 - LOST COMMUNICATION WITH AMMONIA…

18-062-14 ↗

RAM · 2014-11-14

Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L Turbo Diesel. These improvements are separated into the following categories.Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTCs). These DTCs Are Currently Set As A One Trip Fault And Should Be A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeded Learning Limit.These DTCs Are Currently Set As A Two Trip Fault And Should Have Been A One Trip Fault: U12A4 - LOST COMMUNICATION WITH AMMONIA…

18-032-14 REV. A ↗

DODGE · 2014-08-19

Flash: MIL Illumination. Includes Various Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A customer may experience one of more of the following conditions: Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. DTC P061A- Level 2 torque performance set Engine difficult to restart after cold or warm soak periods. Condition occurs in conjunction with the P061A DTC listed above. Applies to vehicles built with 1234YF refrigerant sales code XFC.

18-032-14 ↗

DODGE · 2014-05-10

Flash: MIL Illumination. Includes Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P061A- Level 2 torque performanceCustomers may also experience any of the following symptoms: Engine difficult to restart after cold or warm soak periods. (This condition occurs in conjunction with the P061A DTC listed above). (Applies to vehicles built with 1234YF refrigerant (sales code XFC)).Updating the PCM software will correct the conditions listed above.