P0AA1 · メーカー技術情報

DODGE · 2026-08-07

Powertrain Modules Software Update Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. ● P1614-00 - ECU Reset/Recovery Occurred. ● B1A8A-00 - Multi-Module VIN Handshake Failure. ● P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. ● P1E25-00 - EV Battery Failure Level 2. ● P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. ● P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open. ● P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE-00 – Hybrid/EV Wakeup Control 2…

JEEP · 2026-07-17

Not applicable to vehicles built for US market. Engine Will Not Start If Fault Code P0AA1-09 Is Present Customers may experience the following: ● The engine will not start with display of the message "Electric drive system fault" in the Instrument Panel Cluster (IPC) - if fault code P0AA1-09 is present.

MERCEDES-BENZ, MERCEDES-MAYBACH · 2026-05-20

Complaint 48V battery (A66) part numbers A 000 982 78 24, A 000 982 57 30, A 000 982 88 31, A 000 982 50 32, A 000 982 87 32) may trigger a fault message ("48 V Service Required" with fault codes P0ADA91, P0ADE91, P0AA100, P0ADD00 or P0AA000) in the instrument cluster. This fault message may prevent the 48 V battery contactors from opening automatically if the 12 V power supply is interrupted. In this case, the 48 V on-board electrical system, including connected components, remain energized. Cause The contactors of the 48 V battery do not open, resulting in residual voltage (> 3V) even when the 12 V battery is disconnected. Remedy When working on the 48 V on-board electrical system or connected components, ensure the component being repaired is de-energized in the 48 V system after…

DODGE · 2026-03-14

RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. ● P1614-00 - ECU Reset/Recovery Occurred. ● B1A8A-00 - Multi-Module VIN Handshake Failure. ● P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. ● P1E25-00 - EV Battery Failure Level 2. ● P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. ● P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open. ● P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action…

JEEP · 2026-02-13

Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0607-00 - ECU Internal Performance. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High.** ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failed. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0D0F-00 - Hybrid/ EV Battery Negative Contactor “A” Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck…

JEEP · 2026-02-12

Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0607-00 - ECU Internal Performance. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High.** ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failed. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0D0F-00 - Hybrid/ EV Battery Negative Contactor “A” Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck…

JEEP · 2026-02-12

Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0607-00 - ECU Internal Performance. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High.** ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failed. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0D0F-00 - Hybrid/ EV Battery Negative Contactor “A” Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck…

JEEP · 2026-02-12

Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0607-00 - ECU Internal Performance. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High.** ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failed. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0D0F-00 - Hybrid/ EV Battery Negative Contactor “A” Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck…

JEEP · 2026-02-12

Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0607-00 - ECU Internal Performance. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed.** ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failed. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. **Customers may also experience the following: ● Vehicle…

JEEP · 2026-02-06

Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation SYMPTOM: the technician must find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● P0B28-00 - Hybrid/EV Battery "B" Voltage Unstable. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0607-00 - ECU Internal Performance. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failied. ● P0BBE-00 - Hybrid/EV Battery…

JEEP · 2026-02-06

Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation SYMPTOM: the technician must find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● P0B28-00 Hybrid/EV Battery "B" Voltage Unstable. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0607-00 - ECU Internal Performance. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failied. ● P0BBE-00 - Hybrid/EV Battery…

JEEP · 2026-02-04

Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0B28-00 - Hybrid/EV Battery “B” Voltage Unstable. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failed. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0607-00 - ECU Internal Performance. Customers may also comment on the following: ● Vehicle does not start. NOTE: The…

JEEP · 2026-02-04

Flash: Battery Pack Control Module (BPCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0B28-00 - Hybrid/EV Battery “B” Voltage Unstable. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failed. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0607-00 - ECU Internal Performance.** **Customers may also comment on the following: ● Vehicle does not start.…

JEEP · 2026-01-31

Flash: Battery Pack Control Module (BPCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● **P0B28-00 - Hybrid/EV Battery “B” Voltage Unstable. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0AA1 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0C78 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6 - Hybrid/EV Battery Charging Current High. ● P0B24 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E - Hybrid/EV Battery State Of Health Failed.** ● P1A21-00 - HV Battery Contactor Control Sequence Incorrect. ● P0B3E-00 - Hybrid/EV Battery Voltage Sense 1 Circuit High. ● P0607-00 - ECU Internal Performance. ● P1E1B-00 - Hybrid/EV…

JEEP · 2026-01-31

Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● **P0B28-00 - Hybrid/EV Battery "B" Voltage Unstable.** ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0607-00 - ECU Internal Performance. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failied. ● P0BBE-00 - Hybrid/EV Battery Pack…

JEEP · 2026-01-31

Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● **P0B28-00 Hybrid/EV Battery "B" Voltage Unstable.** ● P0DAB-00 - Hybrid/EV Cell Balancing Performance. ● P0607-00 - ECU Internal Performance. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. ● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. ● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failied. ● P0BBE-00 - Hybrid/EV Battery Pack…

JEEP · 2025-12-18

Flash: Battery Pack Control Module (BPCM) Updates 6B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● **P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. ● P1614-00 - ECU Reset/Recovery Occurred. ● B1A8A-00 - Multi-Module VIN Handshake Failure. ● P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. ● P1E25-00 - EV Battery Failure Level 2. ● P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. ● P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open.** ● P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE-00 – Hybrid/EV…

JEEP · 2025-12-18

RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P1E25-00 - EV Battery Failure Level 2. ● P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. ● P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open.** ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00…

DODGE · 2025-12-18

Flash: Battery Pack Control Module (BPCM) Updates 6B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● **P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. ● P1614-00 - ECU Reset/Recovery Occurred. ● B1A8A-00 - Multi-Module VIN Handshake Failure. ● P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. ● P1E25-00 - EV Battery Failure Level 2. ● P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. ● P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open.** ● P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE-00 – Hybrid/EV…

DODGE · 2025-12-18

Flash: Battery Pack Control Module (BPCM) Updates 11B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P1E25 - EV Battery Failure Level 2 ● P0D10 - Battery Charging System Negative Contactor "A" - Actuator Stuck Open ● P0D09 - Battery Charging System Positive Contactor "A" - Actuator Stuck Open** ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA - Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 - Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1…

JEEP · 2025-12-18

Flash: Battery Pack Control Module (BPCM) Updates 11B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P1E25 - EV Battery Failure Level 2 ● P0D10 - Battery Charging System Negative Contactor "A" - Actuator Stuck Open ● P0D09 - Battery Charging System Positive Contactor "A" - Actuator Stuck Open** ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA - Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 - Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1…

JEEP · 2025-07-10

Flash: Battery Pack Control Module (BPCM) Updates 6A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5…

JEEP · 2025-07-10

RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery…

DODGE · 2025-07-10

RSU With Additional Sleep Cycles for HV Battery Integrity Check -Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5…

DODGE · 2025-07-10

Flash: Battery Pack Control Module (BPCM) Updates 6A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5…

DODGE · 2025-07-10

Flash: Battery Pack Control Module (BPCM) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance.…

JEEP · 2025-07-10

Flash: Battery Pack Control Module (BPCM) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA - Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 - Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5…

FORD · 2025-06-09

This article supersedes TSB 24-2163 to update the Service Procedure and change labor operation from actual to fixed time. Some of the vehicles listed in the Model statement above may exhibit an illuminated powertrain malfunction (wrench) indicator and/or "Stop Safely Now" message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F and/or P0C78 stored in the battery energy control module (BECM). The vehicle may also exhibit a low/discharged 12v battery. This may be due to the high voltage battery junction box.

JEEP · 2025-05-07

RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery…

DODGE · 2025-04-30

"RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery…